ExternalVendorCode/openwrt
1
0
Fork 0
mirror of https://github.com/openwrt/openwrt.git synced 2024-12-27 09:12:39 +00:00
Code Issues Actions 4 Packages Projects Releases Wiki Activity
4eba86820f
openwrt/target/linux/ipq40xx/image/Makefile

220 lines
6.8 KiB
Makefile
Raw Normal View History

ipq40xx: add target Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Mathias Kresin <dev@kresin.me> Signed-off-by: John Crispin <john@phrozen.org>
2018-02-21 19:40:50 +00:00
include $(TOPDIR)/rules.mk
include $(INCLUDE_DIR)/image.mk
define Device/Default
PROFILES := Default
KERNEL_DEPENDS = $$(wildcard $(DTS_DIR)/$$(DEVICE_DTS).dts)
KERNEL_INITRAMFS_PREFIX := $$(IMG_PREFIX)-$(1)-initramfs
KERNEL_PREFIX := $$(IMAGE_PREFIX)
KERNEL_LOADADDR := 0x80208000
SUPPORTED_DEVICES := $(subst _,$(comma),$(1))
IMAGE/sysupgrade.bin = sysupgrade-tar | append-metadata
IMAGE/sysupgrade.bin/squashfs :=
endef
define Device/FitImage
KERNEL_SUFFIX := -fit-uImage.itb
KERNEL = kernel-bin | gzip | fit gzip $$(DTS_DIR)/$$(DEVICE_DTS).dtb
KERNEL_NAME := Image
endef
define Device/FitImageLzma
KERNEL_SUFFIX := -fit-uImage.itb
KERNEL = kernel-bin | lzma | fit lzma $$(DTS_DIR)/$$(DEVICE_DTS).dtb
KERNEL_NAME := Image
endef
define Device/UbiFit
KERNEL_IN_UBI := 1
IMAGES := nand-factory.ubi nand-sysupgrade.bin
IMAGE/nand-factory.ubi := append-ubi
IMAGE/nand-sysupgrade.bin := sysupgrade-tar | append-metadata
endef
ipq40xx: add support for Netgear EX6100v2/EX6150v2 Specifications: SOC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core RAM: 256 MB Winbond W632GU6KB12J FLASH: 16 MiB Macronix MX25L12805D ETH: Qualcomm QCA8072 WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n/ac 2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11n/ac 1x1 (EX6100) 2x2 (EX6150) INPUT: Power, WPS, reset button AP / Range-extender toggle LED: Power, Router, Extender (dual), WPS, Left-/Right-arrow SERIAL: Header next to QCA8072 chip. VCC, TX, RX, GND (Square hole is VCC) WARNING: The serial port needs a TTL/RS-232 v3.3 level converter! The Serial setting is 115200-8-N-1. Tested and working: - Ethernet - 2.4 GHz WiFi (Correct MAC-address) - 5 GHz WiFi (Correct MAC-address) - Factory installation from WebIF - Factory installation from tftp - OpenWRT sysupgrade (Preserving and non-preserving) - LEDs - Buttons Not Working: - AP/Extender toggle-switch Untested: - Support on EX6100v2. They share the same GPL-Code and vendor-images. The 6100v2 seems to lack one 5GHz stream and differs in the 5GHz board-blob. I only own a EX6150v2, therefore i am only able to verify functionality on this device. Install via Web-Interface: Upload the factory image to the device to the Netgear Web-Interface. The device might asks you to confirm the update a second time due to detecting the OpenWRT firmware as older. The device will automatically reboot after the image is written to flash. Install via TFTP: Connect to the devices serial. Hit Enter-Key in bootloader to stop autobooting. Command "fw_recovery" will start a tftp server, waiting for a DNI image to be pushed. Assign your computer the IP-address 192.168.1.10/24. Push image with tftp -4 -v -m binary 192.168.1.1 -c put <OPENWRT_FACTORY> Device will erase factory-partition first, then writes the pushed image to flash and reboots. Parts of this commit are based on Thomas Hebb's work on the openwrt-devel mailinglist. See https://lists.openwrt.org/pipermail/openwrt-devel/2018-January/043418.html Signed-off-by: David Bauer <mail@david-bauer.net>
2018-03-28 22:32:38 +00:00
define Device/DniImage
KERNEL_SUFFIX := -fit-uImage.itb
KERNEL = kernel-bin | gzip | fit gzip $$(DTS_DIR)/$$(DEVICE_DTS).dtb
KERNEL_NAME := Image
NETGEAR_BOARD_ID :=
NETGEAR_HW_ID :=
IMAGES := factory.img sysupgrade.bin
build: consolidate fake uImage header build commands Merge the two existing functions and use a parameter for the type header field. It updates the syntax of the former mpc85xx fake ramdisk header command to be compatible with mkimage from u-boot 2018.03 and fixes the build error spotted by the build bot. Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-04-20 04:30:46 +00:00
IMAGE/factory.img := append-kernel | pad-offset 64k 64 | append-uImage-fakehdr filesystem | pad-to $$$$(KERNEL_SIZE) | append-rootfs | pad-rootfs | netgear-dni
IMAGE/sysupgrade.bin := append-kernel | pad-offset 64k 64 | append-uImage-fakehdr filesystem | pad-to $$$$(KERNEL_SIZE) | append-rootfs | pad-rootfs | append-metadata
ipq40xx: add support for Netgear EX6100v2/EX6150v2 Specifications: SOC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core RAM: 256 MB Winbond W632GU6KB12J FLASH: 16 MiB Macronix MX25L12805D ETH: Qualcomm QCA8072 WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n/ac 2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11n/ac 1x1 (EX6100) 2x2 (EX6150) INPUT: Power, WPS, reset button AP / Range-extender toggle LED: Power, Router, Extender (dual), WPS, Left-/Right-arrow SERIAL: Header next to QCA8072 chip. VCC, TX, RX, GND (Square hole is VCC) WARNING: The serial port needs a TTL/RS-232 v3.3 level converter! The Serial setting is 115200-8-N-1. Tested and working: - Ethernet - 2.4 GHz WiFi (Correct MAC-address) - 5 GHz WiFi (Correct MAC-address) - Factory installation from WebIF - Factory installation from tftp - OpenWRT sysupgrade (Preserving and non-preserving) - LEDs - Buttons Not Working: - AP/Extender toggle-switch Untested: - Support on EX6100v2. They share the same GPL-Code and vendor-images. The 6100v2 seems to lack one 5GHz stream and differs in the 5GHz board-blob. I only own a EX6150v2, therefore i am only able to verify functionality on this device. Install via Web-Interface: Upload the factory image to the device to the Netgear Web-Interface. The device might asks you to confirm the update a second time due to detecting the OpenWRT firmware as older. The device will automatically reboot after the image is written to flash. Install via TFTP: Connect to the devices serial. Hit Enter-Key in bootloader to stop autobooting. Command "fw_recovery" will start a tftp server, waiting for a DNI image to be pushed. Assign your computer the IP-address 192.168.1.10/24. Push image with tftp -4 -v -m binary 192.168.1.1 -c put <OPENWRT_FACTORY> Device will erase factory-partition first, then writes the pushed image to flash and reboots. Parts of this commit are based on Thomas Hebb's work on the openwrt-devel mailinglist. See https://lists.openwrt.org/pipermail/openwrt-devel/2018-January/043418.html Signed-off-by: David Bauer <mail@david-bauer.net>
2018-03-28 22:32:38 +00:00
endef
DEVICE_VARS += NETGEAR_BOARD_ID NETGEAR_HW_ID
ipq40xx: add support for ASUS RT-AC58U/RT-ACRH13 This patch adds support for ASUS RT-AC58U/RT-ACRH13. hardware highlights: SOC: IPQ4018 / QCA Dakota CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7 DRAM: 128 MiB DDR3L-1066 @ 537 MHz (1074?) NT5CC64M16GP-DI NOR: 2 MiB Macronix MX25L1606E (for boot, QSEE) NAND: 128 MiB Winbond W25NO1GVZE1G (cal + kernel + root, UBI) ETH: Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN) USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC) WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2 INPUT: one Reset and one WPS button LEDS: Status, WAN, WIFI1/2, USB and LAN (one blue LED for each) Serial: WARNING: The serial port needs a TTL/RS-232 3V3 level converter! The Serial setting is 115200-8-N-1. The board has an unpopulated 1x4 0.1" header. The pinout (VDD, RX, GND, TX) is printed on the PCB right next to the connector. U-Boot Note: The ethernet driver isn't always reliable and can sometime time out... Don't worry, just retry. Access via the serial console is required. As well as a working TFTP-server setup and the initramfs image. (If not provided, it has to be built from the OpenWrt source. Make sure to enable LZMA as the compression for the INITRAMFS!) To install the image permanently, you have to do the following steps in the listed order. 1. Open up the router. There are four phillips screws hiding behind the four plastic feets on the underside. 2. Connect the serial cable (See notes above) 3. Connect your router via one of the four LAN-ports (yellow) to a PC which can set the IP-Address and ssh and scp from. If possible set your PC's IPv4 Address to 192.168.1.70 (As this is the IP-Address the Router's bootloader expects for the tftp server) 4. power up the router and enter the u-boot choose option 1 to upload the initramfs image. And follow through the ipv4 setup. Wait for your router's status LED to stop blinking rapidly and glow just blue. (The LAN LED should also be glowing blue). 3. Connect to the OpenWrt running in RAM The default IPv4-Address of your router will be 192.168.1.1. 1. Copy over the openwrt-sysupgrade.bin image to your router's temporary directory # scp openwrt-sysupgrade.bin root@192.168.1.1:/tmp 2. ssh from your PC into your router as root. # ssh root@192.168.1.1 The default OpenWrt-Image won't ask for a password. Simply hit the Enter-Key. Once connected...: run the following commands on your temporary installation 3. delete the "jffs2" ubi partition to make room for your new root partition # ubirmvol /dev/ubi0 --name=jffs2 4. install OpenWrt on the NAND Flash. # sysupgrade -v /tmp/openwrt-sysupgrade.bin - This will will automatically reboot the router - Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-03-07 08:13:10 +00:00
ipq40xx: add support for 8devices Jalapeno This patch adds support for 8devices Jalapeno. Specification: QCA IPQ4018, Quad core ARM v7 Cortex A7 717MHz 256 MB of DDR3 RAM 8 MB of SPI NOR flash 128 MB of Winbond SPI NAND flash WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2 requires special BDF in QCA4019/hw1.0/board-2.bin with: bus=ahb,bmi-chip-id=0,bmi-board-id=16,variant=8devices-Jalapeno WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2 requires special BDF in QCA4019/hw1.0/board-2.bin with: bus=ahb,bmi-chip-id=0,bmi-board-id=17,variant=8devices-Jalapeno ETH: Qualcomm Atheros QCA8072 Gigabit Switch (1 x LAN, 1 x WAN) phy@mdio3: Label: eth0 gmac0 phy@mdio4: Label: eth1 gmac1 Installation instructions: Since boards ship with old version of LEDE installation is simple. Just use sysupgrade -n -F sysupgrade.bin Syuspgrade needs to be forced since OpenWRT uses DT detection in recent releases. If you get error that FIT configuration is not found during boot it is due to older U-boot used on your board. That is because 8devices used custom FIT configuration partition name as they internally had v1 and v2 boards. Only v2 boards are sold so now they are shipping boards with never U-boot using generic config@1 FIT partition name. Also for old uboot it is possible to force loading config@1 by changing uboot environment: setenv boot5 'bootm 0x84000000#config@1’ saveenv Signed-off-by: Robert Marko <robimarko@gmail.com>
2018-04-11 09:14:36 +00:00
define Device/8dev_jalapeno
$(call Device/FitImage)
$(call Device/UbiFit)
DEVICE_DTS := qcom-ipq4018-jalapeno
BLOCKSIZE := 128k
PAGESIZE := 2048
DEVICE_TITLE := 8devices Jalapeno
endef
TARGET_DEVICES += 8dev_jalapeno
ipq40xx: add support for ASUS RT-AC58U/RT-ACRH13 This patch adds support for ASUS RT-AC58U/RT-ACRH13. hardware highlights: SOC: IPQ4018 / QCA Dakota CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7 DRAM: 128 MiB DDR3L-1066 @ 537 MHz (1074?) NT5CC64M16GP-DI NOR: 2 MiB Macronix MX25L1606E (for boot, QSEE) NAND: 128 MiB Winbond W25NO1GVZE1G (cal + kernel + root, UBI) ETH: Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN) USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC) WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2 INPUT: one Reset and one WPS button LEDS: Status, WAN, WIFI1/2, USB and LAN (one blue LED for each) Serial: WARNING: The serial port needs a TTL/RS-232 3V3 level converter! The Serial setting is 115200-8-N-1. The board has an unpopulated 1x4 0.1" header. The pinout (VDD, RX, GND, TX) is printed on the PCB right next to the connector. U-Boot Note: The ethernet driver isn't always reliable and can sometime time out... Don't worry, just retry. Access via the serial console is required. As well as a working TFTP-server setup and the initramfs image. (If not provided, it has to be built from the OpenWrt source. Make sure to enable LZMA as the compression for the INITRAMFS!) To install the image permanently, you have to do the following steps in the listed order. 1. Open up the router. There are four phillips screws hiding behind the four plastic feets on the underside. 2. Connect the serial cable (See notes above) 3. Connect your router via one of the four LAN-ports (yellow) to a PC which can set the IP-Address and ssh and scp from. If possible set your PC's IPv4 Address to 192.168.1.70 (As this is the IP-Address the Router's bootloader expects for the tftp server) 4. power up the router and enter the u-boot choose option 1 to upload the initramfs image. And follow through the ipv4 setup. Wait for your router's status LED to stop blinking rapidly and glow just blue. (The LAN LED should also be glowing blue). 3. Connect to the OpenWrt running in RAM The default IPv4-Address of your router will be 192.168.1.1. 1. Copy over the openwrt-sysupgrade.bin image to your router's temporary directory # scp openwrt-sysupgrade.bin root@192.168.1.1:/tmp 2. ssh from your PC into your router as root. # ssh root@192.168.1.1 The default OpenWrt-Image won't ask for a password. Simply hit the Enter-Key. Once connected...: run the following commands on your temporary installation 3. delete the "jffs2" ubi partition to make room for your new root partition # ubirmvol /dev/ubi0 --name=jffs2 4. install OpenWrt on the NAND Flash. # sysupgrade -v /tmp/openwrt-sysupgrade.bin - This will will automatically reboot the router - Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-03-07 08:13:10 +00:00
define Device/asus_rt-ac58u
$(call Device/FitImageLzma)
DEVICE_DTS := qcom-ipq4018-rt-ac58u
BLOCKSIZE := 128k
PAGESIZE := 2048
DTB_SIZE := 65536
DEVICE_TITLE := Asus RT-AC58U
IMAGE_SIZE := 20439364
FILESYSTEMS := squashfs
# Someone - in their infinite wisdom - decided to put the firmware
# version in front of the image name \03\00\00\04 => Version 3.0.0.4
# Since u-boot works with strings we either need another fixup step
# to add a version... or we are very careful not to add '\0' into that
# string and call it a day.... Yeah, we do the latter!
UIMAGE_NAME:=$(shell echo -e '\03\01\01\01RT-AC58U')
IMAGES := sysupgrade.bin
ipq40xx: use upstream board-2.bin The BDFs for all boards were upstreamed to the ath10k-firmware repository and are now part of ath10k-firmware 2018-04-19. Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
2018-04-19 07:12:22 +00:00
DEVICE_PACKAGES := kmod-usb-ledtrig-usbport
ipq40xx: add support for ASUS RT-AC58U/RT-ACRH13 This patch adds support for ASUS RT-AC58U/RT-ACRH13. hardware highlights: SOC: IPQ4018 / QCA Dakota CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7 DRAM: 128 MiB DDR3L-1066 @ 537 MHz (1074?) NT5CC64M16GP-DI NOR: 2 MiB Macronix MX25L1606E (for boot, QSEE) NAND: 128 MiB Winbond W25NO1GVZE1G (cal + kernel + root, UBI) ETH: Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN) USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC) WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2 INPUT: one Reset and one WPS button LEDS: Status, WAN, WIFI1/2, USB and LAN (one blue LED for each) Serial: WARNING: The serial port needs a TTL/RS-232 3V3 level converter! The Serial setting is 115200-8-N-1. The board has an unpopulated 1x4 0.1" header. The pinout (VDD, RX, GND, TX) is printed on the PCB right next to the connector. U-Boot Note: The ethernet driver isn't always reliable and can sometime time out... Don't worry, just retry. Access via the serial console is required. As well as a working TFTP-server setup and the initramfs image. (If not provided, it has to be built from the OpenWrt source. Make sure to enable LZMA as the compression for the INITRAMFS!) To install the image permanently, you have to do the following steps in the listed order. 1. Open up the router. There are four phillips screws hiding behind the four plastic feets on the underside. 2. Connect the serial cable (See notes above) 3. Connect your router via one of the four LAN-ports (yellow) to a PC which can set the IP-Address and ssh and scp from. If possible set your PC's IPv4 Address to 192.168.1.70 (As this is the IP-Address the Router's bootloader expects for the tftp server) 4. power up the router and enter the u-boot choose option 1 to upload the initramfs image. And follow through the ipv4 setup. Wait for your router's status LED to stop blinking rapidly and glow just blue. (The LAN LED should also be glowing blue). 3. Connect to the OpenWrt running in RAM The default IPv4-Address of your router will be 192.168.1.1. 1. Copy over the openwrt-sysupgrade.bin image to your router's temporary directory # scp openwrt-sysupgrade.bin root@192.168.1.1:/tmp 2. ssh from your PC into your router as root. # ssh root@192.168.1.1 The default OpenWrt-Image won't ask for a password. Simply hit the Enter-Key. Once connected...: run the following commands on your temporary installation 3. delete the "jffs2" ubi partition to make room for your new root partition # ubirmvol /dev/ubi0 --name=jffs2 4. install OpenWrt on the NAND Flash. # sysupgrade -v /tmp/openwrt-sysupgrade.bin - This will will automatically reboot the router - Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-03-07 08:13:10 +00:00
endef
TARGET_DEVICES += asus_rt-ac58u
ipq40xx: add target Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Mathias Kresin <dev@kresin.me> Signed-off-by: John Crispin <john@phrozen.org>
2018-02-21 19:40:50 +00:00
define Device/avm_fritzbox-4040
$(call Device/FitImageLzma)
ipq40xx: Adjust SoC name of AVM Fritz!Box 4040 The AVM Fritz!Box 4040 uses an IPQ4018 as SoC and not an IPQ4019. The DTS must be adjusted to reflect this. Signed-off-by: Sven Eckelmann <sven@narfation.org>
2018-03-19 19:53:09 +00:00
DEVICE_DTS := qcom-ipq4018-fritz4040
ipq40xx: add target Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Mathias Kresin <dev@kresin.me> Signed-off-by: John Crispin <john@phrozen.org>
2018-02-21 19:40:50 +00:00
BOARD_NAME := fritz4040
DEVICE_TITLE := AVM Fritz!Box 4040
IMAGE_SIZE := 29753344
ipq40xx: copy Fritz4040 UBoot to STAGING_DIR_IMAGE Copy U-Boot to STAGING_DIR_IMAGE (and append it to the EVA-image from there) to fix image generation using the image-builder. Also remove the bootloader from DEVICE_PACKAGES and instead use the BUILD_DEVICES directive from within the U-Boot makefile. This fixes eva-image generation using the OpenWRT image-builder. Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit 634c733065256979835ca3d7218ae8203a693683)
2019-01-04 20:17:20 +00:00
UBOOT_PATH := $(STAGING_DIR_IMAGE)/uboot-fritz4040.bin
ipq40xx: add eva-image for FRITZ!Box 4040 This commit adds an EVA flashable image for the FRITZ!Box 4040. The image contains the U-Boot with OpenWRT appended to it. This way we remove the need to use UART for initial flashing. Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit 70e6ea319d3bfdfdb34be540dc7d89aa175b5587)
2018-05-15 23:57:16 +00:00
UBOOT_PARTITION_SIZE := 524288
IMAGES = eva.bin sysupgrade.bin
IMAGE/eva.bin := append-uboot | pad-to $$$$(UBOOT_PARTITION_SIZE) | append-kernel | append-rootfs | pad-rootfs
ipq40xx: add target Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Mathias Kresin <dev@kresin.me> Signed-off-by: John Crispin <john@phrozen.org>
2018-02-21 19:40:50 +00:00
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
ipq40xx: copy Fritz4040 UBoot to STAGING_DIR_IMAGE Copy U-Boot to STAGING_DIR_IMAGE (and append it to the EVA-image from there) to fix image generation using the image-builder. Also remove the bootloader from DEVICE_PACKAGES and instead use the BUILD_DEVICES directive from within the U-Boot makefile. This fixes eva-image generation using the OpenWRT image-builder. Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit 634c733065256979835ca3d7218ae8203a693683)
2019-01-04 20:17:20 +00:00
DEVICE_PACKAGES := fritz-tffs fritz-caldata
ipq40xx: add target Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Mathias Kresin <dev@kresin.me> Signed-off-by: John Crispin <john@phrozen.org>
2018-02-21 19:40:50 +00:00
endef
TARGET_DEVICES += avm_fritzbox-4040
ipq40xx: add support for Compex WPJ428 * QCA IPQ4028 * 256 MB of RAM * 32 MB of SPI NOR flash (mx25l25635e) * 128 MB of SPI NAND flash (gd5f1gq4ucy1g) * 2T2R 2.4 GHz - QCA4019 hw1.0 (SoC) - uses AP-DK03 BDF from QCA4019/hw1.0/board-2.bin * 2T2R 5 GHz - QCA4019 hw1.0 (SoC) - uses AP-DK03 BDF from QCA4019/hw1.0/board-2.bin * 2 fully software controllable GPIO-LEDs * 2 additional GPIO-LEDs which also affect the SIM card detection * 1x button (reset) * 1x GPIO buzzer * 1x USB (xHCI) * 1x NGFF (USB-only with Dual-SIM support, untested) * TTL pins are on board (R124 is next to GND, then follows: RX, TX, VCC) * 2x gigabit ethernet - phy@mdio4: + Manual: Ethernet port 0 + gmac0 (ethaddr) in original firmware + 802.3af POE (HV version) + 24v passive POE (LV version) - phy@mdio3: + Manual: Ethernet port 1 + gmac1 (eth1addr) in original firmware * DC Jack connector + 24-56V (HV version) + 12-24V (LV version) The SPI NAND flash isn't supported at the moment. The bootloader has to be updated before OpenWrt is installed to fix a reboot problem. The nor-ipq40xx-single.img from https://downloads.compex.com.sg/?dir=uploads/QSDK/QCA-Reference/WPJ428/b170123-IPQ40xx-Reference-Firmware has to be downloaded and the transfered in u-boot via TFTP set ipaddr 192.168.1.11 set serverip 192.168.1.10 ping ${serverip} tftpboot 0x84000000 nor-ipq40xx-single.img imgaddr=0x84000000 && source $imgaddr:script The sysupgrade image can be installed directly on flash using u-boot: sf probe tftpboot 0x84000000 openwrt-ipq40xx-compex_wpj428-squashfs-sysupgrade.bin sf erase 0x00180000 +$filesize sf write 0x84000000 0x00180000 $filesize bootipq The initramfs image can be started using tftpboot 0x82000000 openwrt-ipq40xx-compex_wpj428-initramfs-fit-uImage.itb set fdt_high 0x83000000 bootm 0x82000000 The used SIM card slot can be changed using # slot 1 (also enables orange LED) echo 1 > /sys/class/gpio/gpio3/value # slot 2 echo 0 > /sys/class/gpio/gpio3/value It can be checked whether a SIM card is inserted in the current slot and the red LED is subsequently on via: echo 2 > /sys/class/gpio/export cat /sys/class/gpio/gpio2/value Signed-off-by: Sven Eckelmann <sven@narfation.org>
2018-03-02 10:56:53 +00:00
define Device/compex_wpj428
$(call Device/FitImage)
DEVICE_DTS := qcom-ipq4028-wpj428
DEVICE_DTS_CONFIG := config@4
BLOCKSIZE := 64k
DEVICE_TITLE := Compex WPJ428
IMAGE_SIZE := 31232k
KERNEL_SIZE := 4096k
IMAGES = sysupgrade.bin
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
ipq40xx: unbundle firmware and board file Don't select the firmware with the board file, it prevents an easy use of the -ct ath10k firmware. Select the firmware within the default packages instead. Remove the per device selection of the firmware now that it the firmware is selected by default. Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-04-12 18:48:35 +00:00
DEVICE_PACKAGES := kmod-gpio-beeper
ipq40xx: add support for Compex WPJ428 * QCA IPQ4028 * 256 MB of RAM * 32 MB of SPI NOR flash (mx25l25635e) * 128 MB of SPI NAND flash (gd5f1gq4ucy1g) * 2T2R 2.4 GHz - QCA4019 hw1.0 (SoC) - uses AP-DK03 BDF from QCA4019/hw1.0/board-2.bin * 2T2R 5 GHz - QCA4019 hw1.0 (SoC) - uses AP-DK03 BDF from QCA4019/hw1.0/board-2.bin * 2 fully software controllable GPIO-LEDs * 2 additional GPIO-LEDs which also affect the SIM card detection * 1x button (reset) * 1x GPIO buzzer * 1x USB (xHCI) * 1x NGFF (USB-only with Dual-SIM support, untested) * TTL pins are on board (R124 is next to GND, then follows: RX, TX, VCC) * 2x gigabit ethernet - phy@mdio4: + Manual: Ethernet port 0 + gmac0 (ethaddr) in original firmware + 802.3af POE (HV version) + 24v passive POE (LV version) - phy@mdio3: + Manual: Ethernet port 1 + gmac1 (eth1addr) in original firmware * DC Jack connector + 24-56V (HV version) + 12-24V (LV version) The SPI NAND flash isn't supported at the moment. The bootloader has to be updated before OpenWrt is installed to fix a reboot problem. The nor-ipq40xx-single.img from https://downloads.compex.com.sg/?dir=uploads/QSDK/QCA-Reference/WPJ428/b170123-IPQ40xx-Reference-Firmware has to be downloaded and the transfered in u-boot via TFTP set ipaddr 192.168.1.11 set serverip 192.168.1.10 ping ${serverip} tftpboot 0x84000000 nor-ipq40xx-single.img imgaddr=0x84000000 && source $imgaddr:script The sysupgrade image can be installed directly on flash using u-boot: sf probe tftpboot 0x84000000 openwrt-ipq40xx-compex_wpj428-squashfs-sysupgrade.bin sf erase 0x00180000 +$filesize sf write 0x84000000 0x00180000 $filesize bootipq The initramfs image can be started using tftpboot 0x82000000 openwrt-ipq40xx-compex_wpj428-initramfs-fit-uImage.itb set fdt_high 0x83000000 bootm 0x82000000 The used SIM card slot can be changed using # slot 1 (also enables orange LED) echo 1 > /sys/class/gpio/gpio3/value # slot 2 echo 0 > /sys/class/gpio/gpio3/value It can be checked whether a SIM card is inserted in the current slot and the red LED is subsequently on via: echo 2 > /sys/class/gpio/export cat /sys/class/gpio/gpio2/value Signed-off-by: Sven Eckelmann <sven@narfation.org>
2018-03-02 10:56:53 +00:00
endef
TARGET_DEVICES += compex_wpj428
ipq40xx: add target Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Mathias Kresin <dev@kresin.me> Signed-off-by: John Crispin <john@phrozen.org>
2018-02-21 19:40:50 +00:00
define Device/glinet_gl-b1300
ipq40xx: fix GL.iNet GL-B1300 support Rename the dts file to match the used SoC type and drop the unnecessary KERNEL_INSTALL from the image build code. Remove the fixed rootfs and kernel partitions and create an image with rootfs appended after kernel. Setup a switch portmap matching the hardware and a default network/switch configuration to make make the second lan port working. Use eth0 as lan to have it consistent accross the target. Use the power LED to indicate the boot status. Sort the SoC entries within the dts by address and use dtc labels whenever possible. Signed-off-by: Mathias Kresin <dev@kresin.me> Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-02-17 08:07:54 +00:00
$(call Device/FitImage)
ipq40xx: add target Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Mathias Kresin <dev@kresin.me> Signed-off-by: John Crispin <john@phrozen.org>
2018-02-21 19:40:50 +00:00
DEVICE_TITLE := GL.iNet GL-B1300
BOARD_NAME := gl-b1300
ipq40xx: fix GL.iNet GL-B1300 support Rename the dts file to match the used SoC type and drop the unnecessary KERNEL_INSTALL from the image build code. Remove the fixed rootfs and kernel partitions and create an image with rootfs appended after kernel. Setup a switch portmap matching the hardware and a default network/switch configuration to make make the second lan port working. Use eth0 as lan to have it consistent accross the target. Use the power LED to indicate the boot status. Sort the SoC entries within the dts by address and use dtc labels whenever possible. Signed-off-by: Mathias Kresin <dev@kresin.me> Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-02-17 08:07:54 +00:00
DEVICE_DTS := qcom-ipq4029-gl-b1300
ipq40xx: add target Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Mathias Kresin <dev@kresin.me> Signed-off-by: John Crispin <john@phrozen.org>
2018-02-21 19:40:50 +00:00
KERNEL_SIZE := 4096k
IMAGE_SIZE := 26624k
IMAGES := sysupgrade.bin
ipq40xx: fix GL.iNet GL-B1300 support Rename the dts file to match the used SoC type and drop the unnecessary KERNEL_INSTALL from the image build code. Remove the fixed rootfs and kernel partitions and create an image with rootfs appended after kernel. Setup a switch portmap matching the hardware and a default network/switch configuration to make make the second lan port working. Use eth0 as lan to have it consistent accross the target. Use the power LED to indicate the boot status. Sort the SoC entries within the dts by address and use dtc labels whenever possible. Signed-off-by: Mathias Kresin <dev@kresin.me> Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-02-17 08:07:54 +00:00
IMAGE/sysupgrade.bin := append-kernel |append-rootfs | pad-rootfs | append-metadata
ipq40xx: add target Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Mathias Kresin <dev@kresin.me> Signed-off-by: John Crispin <john@phrozen.org>
2018-02-21 19:40:50 +00:00
endef
TARGET_DEVICES += glinet_gl-b1300
ipq40xx: add Cisco Meraki MR33 Support This patch adds support for Cisco Meraki MR33 hardware highlights: SOC: IPQ4029 Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7 DRAM: 256 MiB DDR3L-1600 @ 627 MHz Micron MT41K128M16JT-125IT NAND: 128 MiB SLC NAND Spansion S34ML01G200TFV00 (106 MiB usable) ETH: Qualcomm Atheros AR8035 Gigabit PHY (1 x LAN/WAN) + PoE WLAN1: QCA9887 (168c:0050) PCIe 1x1:1 802.11abgn ac Dualband VHT80 WLAN2: Qualcomm Atheros QCA4029 2.4GHz 802.11bgn 2:2x2 WLAN3: Qualcomm Atheros QCA4029 5GHz 802.11a/n/ac 2:2x2 VHT80 LEDS: 1 x Programmable RGB+White Status LED (driven by Ti LP5562 on i2c-1) 1 x Orange LED Fault Indicator (shared with LP5562) 2 x LAN Activity / Speed LEDs (On the RJ45 Port) BUTTON: one Reset button MISC: Bluetooth LE Ti cc2650 PG2.3 4x4mm - BL_CONFIG at 0x0001FFD8 AT24C64 8KiB EEPROM Kensington Lock Serial: WARNING: The serial port needs a TTL/RS-232 3V3 level converter! The Serial setting is 115200-8-N-1. The board has a populated 1x4 0.1" header with half-height/low profile pins. The pinout is: VCC (little white arrow), RX, TX, GND. Flashing needs a serial adaptor, as well as patched ubootwrite utility (needs Little-Endian support). And a modified u-boot (enabled Ethernet). Meraki's original u-boot source can be found in: <https://github.com/riptidewave93/meraki-uboot/tree/mr33-20170427> Add images to do an installation via bootloader: 0. open up the MR33 and connect the serial console. 1. start the 2nd stage bootloader transfer from client pc: # ubootwrite.py --write=mr33-uboot.bin (The ubootwrite tool will interrupt the boot-process and hence it needs to listen for cues. If the connection is bad (due to the low-profile pins), the tool can fail multiple times and in weird ways. If you are not sure, just use a terminal program and see what the device is doing there. 2. power on the MR33 (with ethernet + serial cables attached) Warning: Make sure you do this in a private LAN that has no connection to the internet. - let it upload the u-boot this can take 250-300 seconds - 3. use a tftp client (in binary mode!) on your PC to upload the sysupgrade.bin (the u-boot is listening on 192.168.1.1) # tftp 192.168.1.1 binary put openwrt-ipq40xx-meraki_mr33-squashfs-sysupgrade.bin 4. wait for it to reboot 5. connect to your MR33 via ssh on 192.168.1.1 For more detailed instructions, please take a look at the: "Flashing Instructions for the MR33" PDF. This can be found on the wiki: <https://openwrt.org/toh/meraki/mr33> (A link to the mr33-uboot.bin + the modified ubootwrite is also there) Thanks to Jerome C. for sending an MR33 to Chris. Signed-off-by: Chris Blake <chrisrblake93@gmail.com> Signed-off-by: Mathias Kresin <dev@kresin.me> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-03-10 09:59:18 +00:00
define Device/meraki_mr33
$(call Device/FitImage)
DEVICE_DTS := qcom-ipq4029-mr33
BLOCKSIZE := 131072
PAGESIZE := 2048
DEVICE_TITLE := Cisco Meraki MR33
IMAGES = sysupgrade.bin
ipq40xx: use upstream board-2.bin The BDFs for all boards were upstreamed to the ath10k-firmware repository and are now part of ath10k-firmware 2018-04-19. Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
2018-04-19 07:12:22 +00:00
DEVICE_PACKAGES := -swconfig ath10k-firmware-qca9887
ipq40xx: add Cisco Meraki MR33 Support This patch adds support for Cisco Meraki MR33 hardware highlights: SOC: IPQ4029 Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7 DRAM: 256 MiB DDR3L-1600 @ 627 MHz Micron MT41K128M16JT-125IT NAND: 128 MiB SLC NAND Spansion S34ML01G200TFV00 (106 MiB usable) ETH: Qualcomm Atheros AR8035 Gigabit PHY (1 x LAN/WAN) + PoE WLAN1: QCA9887 (168c:0050) PCIe 1x1:1 802.11abgn ac Dualband VHT80 WLAN2: Qualcomm Atheros QCA4029 2.4GHz 802.11bgn 2:2x2 WLAN3: Qualcomm Atheros QCA4029 5GHz 802.11a/n/ac 2:2x2 VHT80 LEDS: 1 x Programmable RGB+White Status LED (driven by Ti LP5562 on i2c-1) 1 x Orange LED Fault Indicator (shared with LP5562) 2 x LAN Activity / Speed LEDs (On the RJ45 Port) BUTTON: one Reset button MISC: Bluetooth LE Ti cc2650 PG2.3 4x4mm - BL_CONFIG at 0x0001FFD8 AT24C64 8KiB EEPROM Kensington Lock Serial: WARNING: The serial port needs a TTL/RS-232 3V3 level converter! The Serial setting is 115200-8-N-1. The board has a populated 1x4 0.1" header with half-height/low profile pins. The pinout is: VCC (little white arrow), RX, TX, GND. Flashing needs a serial adaptor, as well as patched ubootwrite utility (needs Little-Endian support). And a modified u-boot (enabled Ethernet). Meraki's original u-boot source can be found in: <https://github.com/riptidewave93/meraki-uboot/tree/mr33-20170427> Add images to do an installation via bootloader: 0. open up the MR33 and connect the serial console. 1. start the 2nd stage bootloader transfer from client pc: # ubootwrite.py --write=mr33-uboot.bin (The ubootwrite tool will interrupt the boot-process and hence it needs to listen for cues. If the connection is bad (due to the low-profile pins), the tool can fail multiple times and in weird ways. If you are not sure, just use a terminal program and see what the device is doing there. 2. power on the MR33 (with ethernet + serial cables attached) Warning: Make sure you do this in a private LAN that has no connection to the internet. - let it upload the u-boot this can take 250-300 seconds - 3. use a tftp client (in binary mode!) on your PC to upload the sysupgrade.bin (the u-boot is listening on 192.168.1.1) # tftp 192.168.1.1 binary put openwrt-ipq40xx-meraki_mr33-squashfs-sysupgrade.bin 4. wait for it to reboot 5. connect to your MR33 via ssh on 192.168.1.1 For more detailed instructions, please take a look at the: "Flashing Instructions for the MR33" PDF. This can be found on the wiki: <https://openwrt.org/toh/meraki/mr33> (A link to the mr33-uboot.bin + the modified ubootwrite is also there) Thanks to Jerome C. for sending an MR33 to Chris. Signed-off-by: Chris Blake <chrisrblake93@gmail.com> Signed-off-by: Mathias Kresin <dev@kresin.me> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-03-10 09:59:18 +00:00
endef
TARGET_DEVICES += meraki_mr33
ipq40xx: add support for Netgear EX6100v2/EX6150v2 Specifications: SOC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core RAM: 256 MB Winbond W632GU6KB12J FLASH: 16 MiB Macronix MX25L12805D ETH: Qualcomm QCA8072 WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n/ac 2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11n/ac 1x1 (EX6100) 2x2 (EX6150) INPUT: Power, WPS, reset button AP / Range-extender toggle LED: Power, Router, Extender (dual), WPS, Left-/Right-arrow SERIAL: Header next to QCA8072 chip. VCC, TX, RX, GND (Square hole is VCC) WARNING: The serial port needs a TTL/RS-232 v3.3 level converter! The Serial setting is 115200-8-N-1. Tested and working: - Ethernet - 2.4 GHz WiFi (Correct MAC-address) - 5 GHz WiFi (Correct MAC-address) - Factory installation from WebIF - Factory installation from tftp - OpenWRT sysupgrade (Preserving and non-preserving) - LEDs - Buttons Not Working: - AP/Extender toggle-switch Untested: - Support on EX6100v2. They share the same GPL-Code and vendor-images. The 6100v2 seems to lack one 5GHz stream and differs in the 5GHz board-blob. I only own a EX6150v2, therefore i am only able to verify functionality on this device. Install via Web-Interface: Upload the factory image to the device to the Netgear Web-Interface. The device might asks you to confirm the update a second time due to detecting the OpenWRT firmware as older. The device will automatically reboot after the image is written to flash. Install via TFTP: Connect to the devices serial. Hit Enter-Key in bootloader to stop autobooting. Command "fw_recovery" will start a tftp server, waiting for a DNI image to be pushed. Assign your computer the IP-address 192.168.1.10/24. Push image with tftp -4 -v -m binary 192.168.1.1 -c put <OPENWRT_FACTORY> Device will erase factory-partition first, then writes the pushed image to flash and reboots. Parts of this commit are based on Thomas Hebb's work on the openwrt-devel mailinglist. See https://lists.openwrt.org/pipermail/openwrt-devel/2018-January/043418.html Signed-off-by: David Bauer <mail@david-bauer.net>
2018-03-28 22:32:38 +00:00
define Device/netgear_ex61x0v2
$(call Device/DniImage)
KERNEL_SIZE := 3080192
DEVICE_DTS_CONFIG := config@4
NETGEAR_BOARD_ID := EX6150v2series
NETGEAR_HW_ID := 29765285+16+0+128+2x2
endef
define Device/netgear_ex6100v2
$(call Device/netgear_ex61x0v2)
DEVICE_DTS := qcom-ipq4018-ex6100v2
DEVICE_TITLE := Netgear EX6100v2
endef
TARGET_DEVICES += netgear_ex6100v2
define Device/netgear_ex6150v2
$(call Device/netgear_ex61x0v2)
DEVICE_DTS := qcom-ipq4018-ex6150v2
DEVICE_TITLE := Netgear EX6150v2
endef
TARGET_DEVICES += netgear_ex6150v2
ipq40xx: add target Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Mathias Kresin <dev@kresin.me> Signed-off-by: John Crispin <john@phrozen.org>
2018-02-21 19:40:50 +00:00
define Device/openmesh_a42
$(call Device/FitImageLzma)
ipq40xx: OpenMesh A42 overhaul Sort the soc entries in the dts by address and use dtc labels whenever possible. Adjust the DTS files, the OpenMesh A42 is actually an IPQ4018 and not an IPQ4019. Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-03-10 08:55:18 +00:00
DEVICE_DTS := qcom-ipq4018-a42
ipq40xx: Provide prefered DTS config name for A42 The OpenMesh A42 will use the default config entry in the FIT when no other on is found but prefers the config@om.a42. This only becomes relevant when a Multi-FIT image is prepared for this device. Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
2018-03-19 11:36:13 +00:00
DEVICE_DTS_CONFIG := config@om.a42
ipq40xx: add target Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Mathias Kresin <dev@kresin.me> Signed-off-by: John Crispin <john@phrozen.org>
2018-02-21 19:40:50 +00:00
BLOCKSIZE := 64k
DEVICE_TITLE := OpenMesh A42
KERNEL = kernel-bin | lzma | fit lzma $$(DTS_DIR)/$$(DEVICE_DTS).dtb | pad-to $$(BLOCKSIZE)
IMAGE_SIZE := 15616k
IMAGES = factory.bin sysupgrade.bin
IMAGE/factory.bin := append-rootfs | pad-rootfs | openmesh-image ce_type=A42
IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-rootfs | sysupgrade-tar rootfs=$$$$@ | append-metadata
ipq40xx: unbundle firmware and board file Don't select the firmware with the board file, it prevents an easy use of the -ct ath10k firmware. Select the firmware within the default packages instead. Remove the per device selection of the firmware now that it the firmware is selected by default. Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-04-12 18:48:35 +00:00
DEVICE_PACKAGES := uboot-envtools
ipq40xx: add target Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Mathias Kresin <dev@kresin.me> Signed-off-by: John Crispin <john@phrozen.org>
2018-02-21 19:40:50 +00:00
endef
TARGET_DEVICES += openmesh_a42
ipq40xx: add support for OpenMesh A62 * QCA IPQ4019 * 256 MB of RAM * 32 MB of SPI NOR flash (s25fl256s1) - 2x 15 MB available; but one of the 15 MB regions is the recovery image * 2T2R 2.4 GHz - QCA4019 hw1.0 (SoC) - requires special BDF in QCA4019/hw1.0/board-2.bin with bus=ahb,bmi-chip-id=0,bmi-board-id=20,variant=OM-A62 * 2T2R 5 GHz (channel 36-64) - QCA9888 hw2.0 (PCI) - requires special BDF in QCA9888/hw2.0/board-2.bin bus=pci,bmi-chip-id=0,bmi-board-id=16,variant=OM-A62 * 2T2R 5 GHz (channel 100-165) - QCA4019 hw1.0 (SoC) - requires special BDF in QCA4019/hw1.0/board-2.bin with bus=ahb,bmi-chip-id=0,bmi-board-id=21,variant=OM-A62 * multi-color LED (controlled via red/green/blue GPIOs) * 1x button (reset; kmod-input-gpio-keys compatible) * external watchdog - triggered GPIO * 1x USB (xHCI) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * 2x gigabit ethernet - phy@mdio3: + Label: Ethernet 1 + gmac0 (ethaddr) in original firmware + 802.3at POE+ - phy@mdio4: + Label: Ethernet 2 + gmac1 (eth1addr) in original firmware + 18-24V passive POE (mode B) * powered only via POE The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the factory image to the u-boot when the device boots up. The initramfs image can be started using setenv bootargs 'loglevel=8 earlycon=msm_serial_dm,0x78af000 console=ttyMSM0,115200 mtdparts=spi0.0:256k(0:SBL1),128k(0:MIBIB),384k(0:QSEE),64k(0:CDT),64k(0:DDRPARAMS),64k(0:APPSBLENV),512k(0:APPSBL),64k(0:ART),64k(0:custom),64k(0:KEYS),15552k(inactive),15552k(inactive2)' tftpboot 0x84000000 openwrt-ipq40xx-openmesh_a62-initramfs-fit-uImage.itb set fdt_high 0x85000000 bootm 0x84000000 Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
2017-08-09 11:52:07 +00:00
define Device/openmesh_a62
$(call Device/FitImageLzma)
DEVICE_DTS := qcom-ipq4019-a62
DEVICE_DTS_CONFIG := config@om.a62
BLOCKSIZE := 64k
DEVICE_TITLE := OpenMesh A62
KERNEL = kernel-bin | lzma | fit lzma $$(DTS_DIR)/$$(DEVICE_DTS).dtb | pad-to $$(BLOCKSIZE)
IMAGE_SIZE := 15552k
IMAGES = factory.bin sysupgrade.bin
IMAGE/factory.bin := append-rootfs | pad-rootfs | openmesh-image ce_type=A62
IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-rootfs | sysupgrade-tar rootfs=$$$$@ | append-metadata
DEVICE_PACKAGES := ath10k-firmware-qca9888 uboot-envtools
endef
TARGET_DEVICES += openmesh_a62
ipq40xx: add target Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Mathias Kresin <dev@kresin.me> Signed-off-by: John Crispin <john@phrozen.org>
2018-02-21 19:40:50 +00:00
define Device/qcom_ap-dk01.1-c1
DEVICE_TITLE := QCA AP-DK01.1-C1
BOARD_NAME := ap-dk01.1-c1
DEVICE_DTS := qcom-ipq4019-ap.dk01.1-c1
KERNEL_INSTALL := 1
KERNEL_SIZE := 4096k
IMAGE_SIZE := 26624k
$(call Device/FitImage)
IMAGES := sysupgrade.bin
IMAGE/sysupgrade.bin := append-kernel | pad-to $$$${KERNEL_SIZE} | append-rootfs | pad-rootfs | append-metadata
endef
TARGET_DEVICES += qcom_ap-dk01.1-c1
define Device/qcom_ap-dk04.1-c1
$(call Device/FitImage)
$(call Device/UbiFit)
DEVICE_DTS := qcom-ipq4019-ap.dk04.1-c1
KERNEL_INSTALL := 1
KERNEL_SIZE := 4048k
BLOCKSIZE := 128k
PAGESIZE := 2048
BOARD_NAME := ap-dk04.1-c1
DEVICE_TITLE := QCA AP-DK04.1-C1
endef
TARGET_DEVICES += qcom_ap-dk04.1-c1
ipq40xx: add support for ZyXEL WRE6606 Specifications: SOC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core RAM: 128 MB Nanya NT5CC64M16GP-DI FLASH: 16 MiB Macronix MX25L12845EMI-12G ETH: Qualcomm QCA8072 WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n 2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11n/ac W2 2x2 INPUT: WPS, Mode-toggle-switch LED: Power, WLAN 2.4GHz, WLAN 5GHz, LAN, WPS (LAN not controllable by software) (WLAN each green / red) SERIAL: Header next to eth-phy. VCC, TX, GND, RX (Square hole is VCC) The Serial setting is 115200-8-N-1. Tested and working: - Ethernet (Correct MAC-address) - 2.4 GHz WiFi (Correct MAC-address) - 5 GHz WiFi (Correct MAC-address) - Factory installation from tftp - OpenWRT sysupgrade - LEDs - WPS Button Not Working: - Mode-toggle-switch Install via TFTP: Connect to the devices serial. Hit Enter-Key in bootloader to stop autobooting. Command `tftpboot` will pull an initramfs image named `C0A86302.img` from a tftp server at `192.168.99.08/24`. After successfull transfer, boot the image with `bootm`. To persistently write the firmware, flash an openwrt sysupgrade image from inside the initramfs, for example transfer via `scp <sysupgrade> root@192.168.1.1:/tmp` and flash on the device with `sysupgrade -n /tmp/<sysupgrade>`. append-cmdline patch taken from chunkeeys work on the NBG6617. Signed-off-by: Magnus Frühling <skorpy@frankfurt.ccc.de> Co-authored-by: David Bauer <mail@david-bauer.net> Co-authored-by: Christian Lamparter <chunkeey@googlemail.com> (cherry picked from commit 4b280ad91a6b155ac71c417aaa7bb5f4e328712f)
2018-06-11 21:10:43 +00:00
define Device/zyxel_wre6606
$(call Device/FitImage)
DEVICE_TITLE := ZyXEL WRE6606
DEVICE_DTS_CONFIG := config@4
DEVICE_DTS := qcom-ipq4018-wre6606
DEVICE_PACKAGES := ipq-wifi-zyxel_wre6606
IMAGES := sysupgrade.bin
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
endef
TARGET_DEVICES += zyxel_wre6606
ipq40xx: add target Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Mathias Kresin <dev@kresin.me> Signed-off-by: John Crispin <john@phrozen.org>
2018-02-21 19:40:50 +00:00
$(eval $(call BuildImage))
Reference in New Issue Copy Permalink