openwrt/target/linux/ath79/image/Makefile

88 lines
2.1 KiB
Makefile
Raw Normal View History

include $(TOPDIR)/rules.mk
include $(INCLUDE_DIR)/image.mk
KERNEL_LOADADDR = 0x80060000
DEVICE_VARS += LOADER_FLASH_OFFS LOADER_TYPE
DEVICE_VARS += NETGEAR_BOARD_ID NETGEAR_HW_ID
DEVICE_VARS += RAS_BOARD RAS_ROOTFS_SIZE RAS_VERSION
define Build/combined-image
sh $(TOPDIR)/scripts/combined-image.sh \
"$(IMAGE_KERNEL)" \
"$@" \
"$@.new"
@mv $@.new $@
endef
define Build/loader-common
rm -rf $@.src
$(MAKE) -C lzma-loader \
PKG_BUILD_DIR="$@.src" \
TARGET_DIR="$(dir $@)" LOADER_NAME="$(notdir $@)" \
$(1) compile loader.$(LOADER_TYPE)
mv "$@.$(LOADER_TYPE)" "$@"
rm -rf $@.src
endef
define Build/loader-kernel
$(call Build/loader-common,LOADER_DATA="$@")
endef
define Build/loader-okli-compile
$(call Build/loader-common,FLASH_OFFS=$(LOADER_FLASH_OFFS) FLASH_MAX=0)
endef
# Arguments: <output name> <kernel offset>
define Build/loader-okli
dd if=$(KDIR)/loader-$(word 1,$(1)).$(LOADER_TYPE) bs=$(word 2,$(1)) conv=sync of="$@.new"
cat "$@" >> "$@.new"
mv "$@.new" "$@"
endef
ath79: add support for PISEN WMB001N Specifications: - SoC: AR9341 - RAM: 64M - Flash: 16M - Ethernet: 1 * FE port - WiFi: ar934x-wmac - Sound: WM8918 DAC 1 * 3.5mm headphone jack 2 * RCA connectors for speakers 1 * SPDIF out - USB: 1 * USB2.0 port Flash instruction: Upload generated factory image via vendor's web interface. Notes: A. Audio stuff: 1. Since AR934x, all pins for peripheral blocks can be mapped to any available GPIOs. We currently don't have a PCM/I2S driver for AR934x so pinmux for i2s and SPDIF are bound to i2c gpio node. This should be moved into I2S node when a PCM/I2S driver is available. 2. The i2c-gpio node is for WM8918. DT binding for it can't be added currently due to a missing clock from I2S PLL. B. Factory image: Image contains a image header and a tar.gz archive. 1. Header: A 288 byte header that has nothing to do with appended tarball. Format: 0x0-0x7 and 0x18-0x1F: magic values 0x20: Model number string 0xFC: Action string. It's either "update" or "backup" 0x11C: A 1 byte checksum. It's XOR result of 0x8-0x11B Firmware doesn't care about the rest of the header as long as checksum result is correct. The same header is used for backup and update routines so the magic values and model number can be obtained by generating a backup bin and grab values from it. 2. Tarball: It contains two files named uImage and rootfs, which will be flashed into corresponding mtd partition. Writing a special utility that can only output a fixed binary blob is overkill so factory image header is placed under image/bin instead. C. LED The wifi led has "Wi-Fi" marked on the case but vendor's firmware used it as system status indicator. I did the same in this device support patch. D. Firmware Factory u-boot is built without 'savenv' support so it's impossible to change kernel offset. A 2MB kernel partition won't be enough in the future. OKLI loader is used here to migrate this problem: 1. add OKLI image magic support into uImage parser. 2. build an OKLI loader, compress it with lzma and add a normal uImage header. 3. flash the loader to where the original kernel supposed to be. 4. create a uImage firmware using OKLI loader. 5. flash the created firmware to where rootfs supposed to be. By doing so, u-boot will start OKLI loader, which will then load the actual kernel at 0x20000. The kernel partition is 2MB, which is too much for our loader. To save this space, "mtd-concat" is used here: 1. create a 64K (1 erase block) partition for OKLI loader and create another partition with the left space. 2. concatenate rootfs and this partition into a virtual flash. 3. use the virtual flash for firmware partition. Currently OKLI loader is flashed with factory image only. sysupgrade won't replace it. Since it only has one function and it works for several years, its unlikely to have some bugs that requires a replacement. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-08-04 14:13:45 +00:00
define Build/append-loader-okli
cat "$(KDIR)/loader-$(word 1,$(1)).$(LOADER_TYPE)" >> "$@"
endef
define Build/relocate-kernel
rm -rf $@.relocate
$(CP) ../../generic/image/relocate $@.relocate
$(MAKE) -j1 -C $@.relocate KERNEL_ADDR=$(KERNEL_LOADADDR) CROSS_COMPILE=$(TARGET_CROSS)
( \
dd if=$@.relocate/loader.bin bs=32 conv=sync && \
perl -e '@s = stat("$@"); print pack("N", @s[7])' && \
cat "$@" \
) > "$@.new"
mv "$@.new" "$@"
rm -rf $@.relocate
endef
define Device/Default
DEVICE_DTS_DIR := ../dts
DEVICE_DTS = $$(SOC)_$(1)
PROFILES = Default
MTDPARTS :=
BLOCKSIZE := 64k
KERNEL := kernel-bin | append-dtb | lzma | uImage lzma
KERNEL_INITRAMFS := kernel-bin | append-dtb | lzma | uImage lzma
COMPILE :=
IMAGES := sysupgrade.bin
IMAGE/sysupgrade.bin = append-kernel | pad-to $$$$(BLOCKSIZE) | \
append-rootfs | pad-rootfs | append-metadata | check-size
endef
include $(SUBTARGET).mk
ifeq ($(SUBTARGET),generic)
include generic-tp-link.mk
include generic-ubnt.mk
endif
ifeq ($(SUBTARGET),tiny)
include tiny-netgear.mk
include tiny-tp-link.mk
endif
$(eval $(call BuildImage))