openwrt/target/linux/generic/hack-6.6/765-mxl-gpy-control-LED-reg-from-DT.patch

From 94b90966095f3fa625897e8f53d215882f6e19b3 Mon Sep 17 00:00:00 2001
From: David Bauer <mail@david-bauer.net>
Date: Sat, 11 Mar 2023 17:00:01 +0100
Subject: [PATCH] mxl-gpy: control LED reg from DT

Add dynamic configuration for the LED control registers on MXL PHYs.

This patch has been tested with MaxLinear GPY211C. It is unlikely to be
accepted upstream, as upstream plans on integrating their own framework
for handling these LEDs.

For the time being, use this hack to configure PHY driven device-LEDs to
show the correct state.

A possible alternative might be to expose the LEDs using the kernel LED
framework and bind it to the netdevice. This might also be upstreamable,
although it is a considerable extra amount of work.

Signed-off-by: David Bauer <mail@david-bauer.net>
---
 drivers/net/phy/mxl-gpy.c | 37 ++++++++++++++++++++++++++++++++++++-
 1 file changed, 36 insertions(+), 1 deletion(-)

--- a/drivers/net/phy/mxl-gpy.c
+++ b/drivers/net/phy/mxl-gpy.c
@@ -10,6 +10,7 @@
 #include <linux/bitfield.h>
 #include <linux/hwmon.h>
 #include <linux/mutex.h>
+#include <linux/of.h>
 #include <linux/phy.h>
 #include <linux/polynomial.h>
 #include <linux/property.h>
@@ -38,6 +39,7 @@
 #define PHY_MIISTAT		0x18	/* MII state */
 #define PHY_IMASK		0x19	/* interrupt mask */
 #define PHY_ISTAT		0x1A	/* interrupt status */
+#define PHY_LED			0x1B	/* LED control */
 #define PHY_FWV			0x1E	/* firmware version */
 
 #define PHY_MIISTAT_SPD_MASK	GENMASK(2, 0)
@@ -61,10 +63,15 @@
 				 PHY_IMASK_ADSC | \
 				 PHY_IMASK_ANC)
 
+#define PHY_LED_NUM_LEDS	4
+
 #define PHY_FWV_REL_MASK	BIT(15)
 #define PHY_FWV_MAJOR_MASK	GENMASK(11, 8)
 #define PHY_FWV_MINOR_MASK	GENMASK(7, 0)
 
+/* LED */
+#define VSPEC1_LED(x)		(0x1 + x)
+
 #define PHY_PMA_MGBT_POLARITY	0x82
 #define PHY_MDI_MDI_X_MASK	GENMASK(1, 0)
 #define PHY_MDI_MDI_X_NORMAL	0x3
@@ -270,10 +277,39 @@ out:
 	return ret;
 }
 
+static int gpy_led_write(struct phy_device *phydev)
+{
+	struct device_node *node = phydev->mdio.dev.of_node;
+	u32 led_regs[PHY_LED_NUM_LEDS];
+	int i, ret;
+	u16 val = 0xff00;
+
+	if (!IS_ENABLED(CONFIG_OF_MDIO))
+		return 0;
+
+	if (of_property_read_u32_array(node, "mxl,led-config", led_regs, PHY_LED_NUM_LEDS))
+		return 0;
+
+	if (of_property_read_bool(node, "mxl,led-drive-vdd"))
+		val &= 0x0fff;
+
+	/* Enable LED function handling on all ports*/
+	phy_write(phydev, PHY_LED, val);
+
+	/* Write LED register values */
+	for (i = 0; i < PHY_LED_NUM_LEDS; i++) {
+		ret = phy_write_mmd(phydev, MDIO_MMD_VEND1, VSPEC1_LED(i), (u16)led_regs[i]);
+		if (ret < 0)
+			return ret;
+	}
+
+	return 0;
+}
+
 static int gpy_config_init(struct phy_device *phydev)
 {
 	/* Nothing to configure. Configuration Requirement Placeholder */
-	return 0;
+	return gpy_led_write(phydev);
 }
 
 static int gpy_probe(struct phy_device *phydev)