openwrt/target/linux/ath79/dts/ar9344_qxwlan_e750g-v8-8m.dts

60 lines
1.0 KiB
Plaintext
Raw Normal View History

ath79: add support for Qxwlan E750G v8 Qxwlan E750G v8 is based on Qualcomm QCA9344 + QCA9334. Specification: - 560/450/225 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 8/16 MB of FLASH (SPI NOR) - 2T2R 2.4G GHz (AR9344) - 2x 10/100/1000 Mbps Ethernet (one port with PoE support) - 7x LED (6 driven by GPIO) - 1x button (reset) - 1x DC jack for main power input (9-48 V) - UART (J23) and LEDs (J2) headers on PCB Flash instruction: 1.Using tftp mode with UART connection and original LEDE image - Configure PC with static IP 192.168.1.10 and tftp server. - Rename "openwrt-ar71xx-generic-xxx-squashfs-sysupgrade.bin" to "firmware.bin" and place it in tftp server directory. - Connect PC with one of LAN ports, power up the router and press key "Enter" to access U-Boot CLI. - Use the following commands to update the device to LEDE: run lfw - After that the device will reboot and boot to LEDE. - Wait until all LEDs stops flashing and use the router. 2.Using httpd mode with Web UI connection and original LEDE image - Configure PC with static IP 192.168.1.xxx(2-255) and tftp server. - Connect PC with one of LAN ports,press the reset button, power up the router and keep button pressed for around 6-7 seconds, until leds flashing. - Open your browser and enter 192.168.1.1,You will see the upgrade interface, select "openwrt-ar71xx-generic-xxx-squashfs- sysupgrade.bin" and click the upgrade button. - After that the device will reboot and boot to LEDE. - Wait until all LEDs stops flashing and use the router. Signed-off-by: 张鹏 <sd20@qxwlan.com> [cut out of bigger patch, keep swconfig] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-10-14 07:47:35 +00:00
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
#include "ar9344_qxwlan_e750x.dtsi"
/ {
model = "Qxwlan E750G v8 8M";
compatible = "qxwlan,e750g-v8-8m", "qca,ar9344";
};
&mdio0 {
status = "okay";
phy-mask = <0>;
phy0: ethernet-phy@0 {
reg = <0>;
phy-mode = "rgmii";
qca,ar8327-initvals = <
0x04 0x07600000 /* PORT0 PAD MODE CTRL */
0x10 0x81000080 /* POWER_ON_STRAP */
0x50 0xcc35cc35 /* LED_CTRL0 */
0x54 0xca35ca35 /* LED_CTRL1 */
0x58 0xc935c935 /* LED_CTRL2 */
0x5c 0x03ffff00 /* LED_CTRL3 */
0x7c 0x0000007e /* PORT0_STATUS */
>;
};
};
&eth0 {
status = "okay";
pll-data = <0x06000000 0x00000101 0x00001616>;
nvmem-cells = <&macaddr_pridata_400>;
nvmem-cell-names = "mac-address";
ath79: add support for Qxwlan E750G v8 Qxwlan E750G v8 is based on Qualcomm QCA9344 + QCA9334. Specification: - 560/450/225 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 8/16 MB of FLASH (SPI NOR) - 2T2R 2.4G GHz (AR9344) - 2x 10/100/1000 Mbps Ethernet (one port with PoE support) - 7x LED (6 driven by GPIO) - 1x button (reset) - 1x DC jack for main power input (9-48 V) - UART (J23) and LEDs (J2) headers on PCB Flash instruction: 1.Using tftp mode with UART connection and original LEDE image - Configure PC with static IP 192.168.1.10 and tftp server. - Rename "openwrt-ar71xx-generic-xxx-squashfs-sysupgrade.bin" to "firmware.bin" and place it in tftp server directory. - Connect PC with one of LAN ports, power up the router and press key "Enter" to access U-Boot CLI. - Use the following commands to update the device to LEDE: run lfw - After that the device will reboot and boot to LEDE. - Wait until all LEDs stops flashing and use the router. 2.Using httpd mode with Web UI connection and original LEDE image - Configure PC with static IP 192.168.1.xxx(2-255) and tftp server. - Connect PC with one of LAN ports,press the reset button, power up the router and keep button pressed for around 6-7 seconds, until leds flashing. - Open your browser and enter 192.168.1.1,You will see the upgrade interface, select "openwrt-ar71xx-generic-xxx-squashfs- sysupgrade.bin" and click the upgrade button. - After that the device will reboot and boot to LEDE. - Wait until all LEDs stops flashing and use the router. Signed-off-by: 张鹏 <sd20@qxwlan.com> [cut out of bigger patch, keep swconfig] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-10-14 07:47:35 +00:00
phy-mode = "rgmii";
phy-handle = <&phy0>;
};
&partitions {
partition@70000 {
compatible = "denx,uimage";
label = "firmware";
reg = <0x070000 0x790000>;
};
};
&pridata {
compatible = "nvmem-cells";
#address-cells = <1>;
#size-cells = <1>;
macaddr_pridata_400: macaddr@400 {
reg = <0x400 0x6>;
};
};