openwrt/target/linux/ramips/dts/mt7620a_wavlink_wl-wn579x3.dts

// SPDX-License-Identifier: GPL-2.0-or-later

#include "mt7620a.dtsi"

#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>

/ {
	compatible = "wavlink,wl-wn579x3", "ralink,mt7620a-soc";
	model = "Wavlink WL-WN579X3";

	aliases {
		led-boot = &led_wps;
		led-failsafe = &led_wps;
		led-running = &led_wps;
		led-upgrade = &led_wps;
	};

	keys {
		compatible = "gpio-keys";

		reset {
			label = "reset";
			gpios = <&gpio0 1 GPIO_ACTIVE_LOW>;
			linux,code = <KEY_RESTART>;
		};

		wps {
			label = "wps";
			gpios = <&gpio0 2 GPIO_ACTIVE_LOW>;
			linux,code = <KEY_WPS_BUTTON>;
		};

		switch_aps {
			label = "mode_aps";
			gpios = <&gpio0 11 GPIO_ACTIVE_LOW>;
			linux,code = <BTN_1>;
			linux,input-type = <EV_SW>;
		};

		switch_repeater {
			label = "mode_repeater";
			gpios = <&gpio0 9 GPIO_ACTIVE_LOW>;
			linux,code = <BTN_0>;
			linux,input-type = <EV_SW>;
		};
	};

	leds {
		compatible = "gpio-leds";

		led_wps: wps {
			label = "blue:wps";
			gpios = <&gpio2 2 GPIO_ACTIVE_LOW>;
		};

		lan {
			label = "blue:lan";
			gpios = <&gpio2 4 GPIO_ACTIVE_LOW>;
		};

		wan {
			label = "blue:wan";
			gpios = <&gpio2 1 GPIO_ACTIVE_LOW>;
		};

		wifi {
			label = "blue:wifi";
			gpios = <&gpio3 0 GPIO_ACTIVE_LOW>;
		};

		/* These three form the signal wifi strength segments */
		wifi_high {
			label = "blue:wifi_high";
			gpios = <&gpio0 13 GPIO_ACTIVE_LOW>;
		};

		wifi_medium {
			label = "blue:wifi_medium";
			gpios = <&gpio0 12 GPIO_ACTIVE_LOW>;
		};

		wifi_low {
			label = "blue:wifi_low";
			gpios = <&gpio2 3 GPIO_ACTIVE_LOW>;
		};
	};
};

&gpio2 {
	status = "okay";
};

&gpio3 {
	status = "okay";
};

&spi0 {
	status = "okay";

	flash@0 {
		compatible = "jedec,spi-nor";
		reg = <0>;
		spi-max-frequency = <50000000>;

		partitions {
			compatible = "fixed-partitions";
			#address-cells = <1>;
			#size-cells = <1>;

			partition@0 {
				label = "u-boot";
				reg = <0x0 0x30000>;
				read-only;
			};

			partition@30000 {
				label = "config";
				reg = <0x30000 0x10000>;
				read-only;
			};

			factory: partition@40000 {
				label = "factory";
				reg = <0x40000 0x10000>;
				read-only;

				nvmem-layout {
					compatible = "fixed-layout";
					#address-cells = <1>;
					#size-cells = <1>;

					eeprom_factory_0: eeprom@0 {
						reg = <0x0 0x200>;
					};

					eeprom_factory_8000: eeprom@8000 {
						reg = <0x8000 0x200>;
					};

					macaddr_factory_28: macaddr@28 {
						reg = <0x28 0x6>;
					};
				};
			};

			partition@50000 {
				compatible = "denx,uimage";
				label = "firmware";
				reg = <0x50000 0x790000>;
			};

			partition@7e0000 {
				label = "board_data";
				reg = <0x7e0000 0x10000>;
				read-only;
			};

			partition@7f0000 {
				label = "nvram";
				reg = <0x7f0000 0x10000>;
				read-only;
			};
		};
	};
};

&pcie {
	status = "okay";
};

&pcie0 {
	wifi@0,0 {
		reg = <0x0000 0 0 0 0>;
		nvmem-cells = <&eeprom_factory_8000>;
		nvmem-cell-names = "eeprom";
		ieee80211-freq-limit = <5000000 6000000>;
	};
};

&ethernet {
	pinctrl-names = "default";
	pinctrl-0 = <&rgmii1_pins &rgmii2_pins &mdio_pins>;

	nvmem-cells = <&macaddr_factory_28>;
	nvmem-cell-names = "mac-address";

	mediatek,portmap = "llllw";

	port@4 {
		status = "okay";
		phy-handle = <&phy4>;
		phy-mode = "rgmii";
	};

	port@5 {
		status = "okay";
		phy-handle = <&phy5>;
		phy-mode = "rgmii";
	};

	mdio-bus {
		status = "okay";

		phy4: ethernet-phy@4 {
			reg = <4>;
			phy-mode = "rgmii";
		};

		phy5: ethernet-phy@5 {
			reg = <5>;
			phy-mode = "rgmii";
		};
	};
};

&gsw {
	mediatek,port4-gmac;
	mediatek,ephy-base = /bits/ 8 <8>;
};

&wmac {
	nvmem-cells = <&eeprom_factory_0>;
	nvmem-cell-names = "eeprom";
};

&state_default {
	gpio {
		groups = "ephy", "i2c", "wled", "uartf";
		function = "gpio";
	};
};