openwrt/target/linux/ipq806x/image/Makefile

244 lines
7.0 KiB
Makefile
Raw Normal View History

# Copyright (c) 2014 The Linux Foundation. All rights reserved.
#
include $(TOPDIR)/rules.mk
include $(INCLUDE_DIR)/image.mk
define Device/Default
PROFILES := Default
KERNEL_DEPENDS = $$(wildcard $(DTS_DIR)/$$(DEVICE_DTS).dts)
KERNEL_INITRAMFS_PREFIX := $$(IMG_PREFIX)-$(1)-initramfs
KERNEL_PREFIX := $$(IMAGE_PREFIX)
ipq806x: add ipq4019 fritz4040 support This patch adds support for AVM FRITZ!Box 4040. hardware highlights: SOC: IPQ4018 / QCA Dakota CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7 DRAM: 256 MiB Nanya NT5CC128M16IP FLASH: 32 MiB MXIC MX25L25635FMI ETH: Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN) USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC) 1 x 2.0 (via Synopsys DesignWare DWC3 controller in the SoC) WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2 INPUT: one WLAN and one WPS button LEDS: Power, WAN/Internet, WIFI, INFO (red and amber) and LAN. Serial: WARNING: The serial port needs a TTL/RS-232 v3.3 level converter! The Serial setting is 115200-8-N-1. The SoC's serial port is right next to the MXIC FLASH chip. The board has a unpopulated 1x4 0.1" header for it. Use a multimeter to figure out the pinout! This board currently needs an additional u-boot image in order to boot properly. Booting with EVA isn't possible ATM. Install Procedure: 0. It's highly recommended to connect to the serial port. The serial settings are listed above. 1. install a u-boot image for AVM Fritz!Box 4040 (see <https://github.com/chunkeey/FritzBox-4040-UBOOT/releases> and <https://github.com/chunkeey/FritzBox-4040-UBOOT/blob/master/upload-to-f4040.sh>) 2. upload the initramfs.itb image via tftp (u-boot listens to 192.168.1.1 - use binary transfer mode!) 3. connect to the FB4040 and use sysupgrade sysupgrade.bin to install the image. Works: - Switch and Ethernet (99%) - Buttons (WLAN, WPS) - FLASH (1 x 32MiB NOR Chip) - WLAN2G and WLAN5G - CPUFREQ scaling - PRNG - serial - Crypto Accelerator - sysupgrade (Read the flash instructions to avoid bricking) - full LEDE Install (Read the flash instructions to avoid bricking) - LEDs (Power, WAN, Info (red and amber), LAN) The LEDs are connected to the QCA8075 LED ports. The AR40xx driver contains a gpio-controller to handle these special "GPIOs". - USB Both 3.0 and 2.0 ports - many packages from other ARMv7 boards (This does include the RaspberryPi Model 2!) - ... Not planned: - WAN<->LAN short-cut - Qualcomm Secure Execution Environment - ... Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John Crispin <john@phrozen.org>
2017-03-14 16:04:28 +00:00
KERNEL_LOADADDR = 0x42208000
SUPPORTED_DEVICES := $(subst _,$(comma),$(1))
IMAGE/sysupgrade.bin = sysupgrade-tar | append-metadata
IMAGE/sysupgrade.bin/squashfs :=
endef
define Device/LegacyImage
KERNEL_SUFFIX := -uImage
KERNEL = kernel-bin | append-dtb | uImage none
KERNEL_NAME := zImage
endef
define Device/FitImage
KERNEL_SUFFIX := -fit-uImage.itb
KERNEL = kernel-bin | gzip | fit gzip $$(DTS_DIR)/$$(DEVICE_DTS).dtb
KERNEL_NAME := Image
endef
ipq806x: add ipq4019 fritz4040 support This patch adds support for AVM FRITZ!Box 4040. hardware highlights: SOC: IPQ4018 / QCA Dakota CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7 DRAM: 256 MiB Nanya NT5CC128M16IP FLASH: 32 MiB MXIC MX25L25635FMI ETH: Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN) USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC) 1 x 2.0 (via Synopsys DesignWare DWC3 controller in the SoC) WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2 INPUT: one WLAN and one WPS button LEDS: Power, WAN/Internet, WIFI, INFO (red and amber) and LAN. Serial: WARNING: The serial port needs a TTL/RS-232 v3.3 level converter! The Serial setting is 115200-8-N-1. The SoC's serial port is right next to the MXIC FLASH chip. The board has a unpopulated 1x4 0.1" header for it. Use a multimeter to figure out the pinout! This board currently needs an additional u-boot image in order to boot properly. Booting with EVA isn't possible ATM. Install Procedure: 0. It's highly recommended to connect to the serial port. The serial settings are listed above. 1. install a u-boot image for AVM Fritz!Box 4040 (see <https://github.com/chunkeey/FritzBox-4040-UBOOT/releases> and <https://github.com/chunkeey/FritzBox-4040-UBOOT/blob/master/upload-to-f4040.sh>) 2. upload the initramfs.itb image via tftp (u-boot listens to 192.168.1.1 - use binary transfer mode!) 3. connect to the FB4040 and use sysupgrade sysupgrade.bin to install the image. Works: - Switch and Ethernet (99%) - Buttons (WLAN, WPS) - FLASH (1 x 32MiB NOR Chip) - WLAN2G and WLAN5G - CPUFREQ scaling - PRNG - serial - Crypto Accelerator - sysupgrade (Read the flash instructions to avoid bricking) - full LEDE Install (Read the flash instructions to avoid bricking) - LEDs (Power, WAN, Info (red and amber), LAN) The LEDs are connected to the QCA8075 LED ports. The AR40xx driver contains a gpio-controller to handle these special "GPIOs". - USB Both 3.0 and 2.0 ports - many packages from other ARMv7 boards (This does include the RaspberryPi Model 2!) - ... Not planned: - WAN<->LAN short-cut - Qualcomm Secure Execution Environment - ... Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John Crispin <john@phrozen.org>
2017-03-14 16:04:28 +00:00
define Device/FitImageLzma
KERNEL_SUFFIX := -fit-uImage.itb
KERNEL = kernel-bin | lzma | fit lzma $$(DTS_DIR)/$$(DEVICE_DTS).dtb
KERNEL_NAME := Image
endef
define Device/UbiFit
KERNEL_IN_UBI := 1
ipq806x: add support for Compex WPQ864 Hardware highlights: - SoC: Qualcomm Atheros IPQ8064/5 ARM Dual Core CPU - RAM: (512MB or 1GB) DDR3 System Memory - Storage: 32MB NOR (Cypress S25FL256S1) 256MB NAND (Micron MT29F2G08ABBEAH4) - Ethernet: 5 x 1G via QCA8337N - USB: 1 x USB 2.0/3.0 + 1 x USB 2.0 on mini PCIe3 socket - PCIe: 3x mini PCIe (third mini PCIE3 is PCIe/USB shared) - SIM Card Slot: 2 x Slot - Buttons: Reset Button - LEDs: 18x, 8x GPIO controllable - Buzzer The correct amount of RAM will be passed by the bootloader. In contrast to the documentation provided by Compex, the third PCIe doesn't use GPIO16 for PERST. Instead, GPIO3 is shared and used as PERST for PCIe0 and PCIe2. So far, no one was able to get USB 3.0 working with the 1GB RAM version, while it works fine for my 512MB version. Since USB 3.0 doesn't work with the Compex firmware for the 1G variant either, it could be a hardware issue with these boards. OpenWrt will be installed to the NAND flash. Make sure to have a full working image on the NOR flash. It will be the backup in case anything goes wrong. It has been observed that an image loaded via tftpboot might have bitflips. Hence the extra step to create a crc32 checksum to allow to compare the checksum with the one from the source file prior to flashing. In all cases it is necessary to set the following u-boot parameter to an empty (whitespace) value, to ensure that the chosen bootargs of the dts isn't overwritten or set to bogus - not working - values: (IPQ) # set bootargs " " (IPQ) # set fsbootargs " " (IPQ) # saveenv The sysupgrade image can be installed directly on flash using u-boot (put jumper in JP13 (leave JP9 open) to boot from nand): (IPQ) # set serverip 192.168.1.20 (IPQ) # set ipaddr 192.168.1.1 (IPQ) # tftpboot 0x42000000 openwrt-ipq806x-compex_wpq864-squashfs-nand-factory.bin (IPQ) # crc32 0x42000000 $filesize (IPQ) # nand erase 0x1340000 0x4000000 (IPQ) # nand write 0x42000000 0x1340000 $filesize The initramfs image can be started using: (IPQ) # set fdt_high 0x48000000 (IPQ) # tftpboot 0x44000000 openwrt-ipq806x-compex_wpq864-initramfs-fit-uImage.itb (IPQ) # bootm 0x44000000 Signed-off-by: Christian Mehlis <christian@m3hlis.de> Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-10-30 08:51:54 +00:00
IMAGES := nand-factory.bin nand-sysupgrade.bin
IMAGE/nand-factory.bin := append-ubi
IMAGE/nand-sysupgrade.bin := sysupgrade-tar | append-metadata
endef
define Device/DniImage
KERNEL_SUFFIX := -uImage
KERNEL = kernel-bin | append-dtb | uImage none
KERNEL_NAME := zImage
NETGEAR_BOARD_ID :=
NETGEAR_HW_ID :=
UBINIZE_OPTS := -E 5
IMAGES := factory.img sysupgrade.bin
IMAGE/factory.img := append-kernel | pad-offset $$$$(BLOCKSIZE) 64 | append-uImage-fakehdr filesystem | pad-to $$$$(KERNEL_SIZE) | append-ubi | netgear-dni
IMAGE/sysupgrade.bin := append-kernel | pad-offset $$$$(BLOCKSIZE) 64 | append-uImage-fakehdr filesystem | sysupgrade-tar kernel=$$$$@ | append-metadata
endef
DEVICE_VARS += NETGEAR_BOARD_ID NETGEAR_HW_ID
define Device/TpSafeImage
KERNEL_SUFFIX := -uImage
KERNEL = kernel-bin | append-dtb | uImage none
KERNEL_NAME := zImage
TPLINK_BOARD_ID :=
IMAGES := factory.bin sysupgrade.bin
IMAGE/factory.bin := append-rootfs | tplink-safeloader factory
IMAGE/sysupgrade.bin := append-rootfs | tplink-safeloader sysupgrade | append-metadata
endef
DEVICE_VARS += TPLINK_BOARD_ID
define Device/ZyXELImage
KERNEL_SUFFIX := -uImage
KERNEL = kernel-bin | append-dtb | uImage none | pad-to $${KERNEL_SIZE}
KERNEL_NAME := zImage
IMAGES := sysupgrade.bin mmcblk0p5-rootfs.bin mmcblk0p4-kernel.bin
IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-to $$$${BLOCKSIZE} | sysupgrade-tar rootfs=$$$$@ | append-metadata
IMAGE/mmcblk0p5-rootfs.bin := append-rootfs | pad-rootfs | pad-to $$$${BLOCKSIZE}
IMAGE/mmcblk0p4-kernel.bin := append-kernel
endef
ipq806x: add support for Compex WPQ864 Hardware highlights: - SoC: Qualcomm Atheros IPQ8064/5 ARM Dual Core CPU - RAM: (512MB or 1GB) DDR3 System Memory - Storage: 32MB NOR (Cypress S25FL256S1) 256MB NAND (Micron MT29F2G08ABBEAH4) - Ethernet: 5 x 1G via QCA8337N - USB: 1 x USB 2.0/3.0 + 1 x USB 2.0 on mini PCIe3 socket - PCIe: 3x mini PCIe (third mini PCIE3 is PCIe/USB shared) - SIM Card Slot: 2 x Slot - Buttons: Reset Button - LEDs: 18x, 8x GPIO controllable - Buzzer The correct amount of RAM will be passed by the bootloader. In contrast to the documentation provided by Compex, the third PCIe doesn't use GPIO16 for PERST. Instead, GPIO3 is shared and used as PERST for PCIe0 and PCIe2. So far, no one was able to get USB 3.0 working with the 1GB RAM version, while it works fine for my 512MB version. Since USB 3.0 doesn't work with the Compex firmware for the 1G variant either, it could be a hardware issue with these boards. OpenWrt will be installed to the NAND flash. Make sure to have a full working image on the NOR flash. It will be the backup in case anything goes wrong. It has been observed that an image loaded via tftpboot might have bitflips. Hence the extra step to create a crc32 checksum to allow to compare the checksum with the one from the source file prior to flashing. In all cases it is necessary to set the following u-boot parameter to an empty (whitespace) value, to ensure that the chosen bootargs of the dts isn't overwritten or set to bogus - not working - values: (IPQ) # set bootargs " " (IPQ) # set fsbootargs " " (IPQ) # saveenv The sysupgrade image can be installed directly on flash using u-boot (put jumper in JP13 (leave JP9 open) to boot from nand): (IPQ) # set serverip 192.168.1.20 (IPQ) # set ipaddr 192.168.1.1 (IPQ) # tftpboot 0x42000000 openwrt-ipq806x-compex_wpq864-squashfs-nand-factory.bin (IPQ) # crc32 0x42000000 $filesize (IPQ) # nand erase 0x1340000 0x4000000 (IPQ) # nand write 0x42000000 0x1340000 $filesize The initramfs image can be started using: (IPQ) # set fdt_high 0x48000000 (IPQ) # tftpboot 0x44000000 openwrt-ipq806x-compex_wpq864-initramfs-fit-uImage.itb (IPQ) # bootm 0x44000000 Signed-off-by: Christian Mehlis <christian@m3hlis.de> Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-10-30 08:51:54 +00:00
define Device/compex_wpq864
$(call Device/FitImage)
$(call Device/UbiFit)
BLOCKSIZE := 128k
PAGESIZE := 2048
DEVICE_DTS := qcom-ipq8064-wpq864
DEVICE_TITLE := Compex WPQ864
DEVICE_PACKAGES := kmod-gpio-beeper
endef
TARGET_DEVICES += compex_wpq864
define Device/linksys_ea8500
$(call Device/LegacyImage)
DEVICE_DTS := qcom-ipq8064-ea8500
PAGESIZE := 2048
BLOCKSIZE := 128k
KERNEL_SIZE := 3072k
KERNEL = kernel-bin | append-dtb | uImage none | append-uImage-fakehdr filesystem
BOARD_NAME := ea8500
SUPPORTED_DEVICES += ea8500
UBINIZE_OPTS := -E 5
IMAGES := factory.bin sysupgrade.bin
IMAGE/factory.bin := append-kernel | pad-to $$$${KERNEL_SIZE} | append-ubi
DEVICE_TITLE := Linksys EA8500
DEVICE_PACKAGES := ath10k-firmware-qca99x0
endef
TARGET_DEVICES += linksys_ea8500
define Device/netgear_d7800
$(call Device/DniImage)
DEVICE_DTS := qcom-ipq8064-d7800
KERNEL_SIZE := 4194304
NETGEAR_BOARD_ID := D7800
NETGEAR_HW_ID := 29764958+0+128+512+4x4+4x4
BLOCKSIZE := 128k
PAGESIZE := 2048
BOARD_NAME := d7800
SUPPORTED_DEVICES += d7800
DEVICE_TITLE := Netgear Nighthawk X4 D7800
DEVICE_PACKAGES := ath10k-firmware-qca99x0
ipq806x: add ipq4019 fritz4040 support This patch adds support for AVM FRITZ!Box 4040. hardware highlights: SOC: IPQ4018 / QCA Dakota CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7 DRAM: 256 MiB Nanya NT5CC128M16IP FLASH: 32 MiB MXIC MX25L25635FMI ETH: Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN) USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC) 1 x 2.0 (via Synopsys DesignWare DWC3 controller in the SoC) WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2 INPUT: one WLAN and one WPS button LEDS: Power, WAN/Internet, WIFI, INFO (red and amber) and LAN. Serial: WARNING: The serial port needs a TTL/RS-232 v3.3 level converter! The Serial setting is 115200-8-N-1. The SoC's serial port is right next to the MXIC FLASH chip. The board has a unpopulated 1x4 0.1" header for it. Use a multimeter to figure out the pinout! This board currently needs an additional u-boot image in order to boot properly. Booting with EVA isn't possible ATM. Install Procedure: 0. It's highly recommended to connect to the serial port. The serial settings are listed above. 1. install a u-boot image for AVM Fritz!Box 4040 (see <https://github.com/chunkeey/FritzBox-4040-UBOOT/releases> and <https://github.com/chunkeey/FritzBox-4040-UBOOT/blob/master/upload-to-f4040.sh>) 2. upload the initramfs.itb image via tftp (u-boot listens to 192.168.1.1 - use binary transfer mode!) 3. connect to the FB4040 and use sysupgrade sysupgrade.bin to install the image. Works: - Switch and Ethernet (99%) - Buttons (WLAN, WPS) - FLASH (1 x 32MiB NOR Chip) - WLAN2G and WLAN5G - CPUFREQ scaling - PRNG - serial - Crypto Accelerator - sysupgrade (Read the flash instructions to avoid bricking) - full LEDE Install (Read the flash instructions to avoid bricking) - LEDs (Power, WAN, Info (red and amber), LAN) The LEDs are connected to the QCA8075 LED ports. The AR40xx driver contains a gpio-controller to handle these special "GPIOs". - USB Both 3.0 and 2.0 ports - many packages from other ARMv7 boards (This does include the RaspberryPi Model 2!) - ... Not planned: - WAN<->LAN short-cut - Qualcomm Secure Execution Environment - ... Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John Crispin <john@phrozen.org>
2017-03-14 16:04:28 +00:00
endef
TARGET_DEVICES += netgear_d7800
ipq806x: add ipq4019 fritz4040 support This patch adds support for AVM FRITZ!Box 4040. hardware highlights: SOC: IPQ4018 / QCA Dakota CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7 DRAM: 256 MiB Nanya NT5CC128M16IP FLASH: 32 MiB MXIC MX25L25635FMI ETH: Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN) USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC) 1 x 2.0 (via Synopsys DesignWare DWC3 controller in the SoC) WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2 INPUT: one WLAN and one WPS button LEDS: Power, WAN/Internet, WIFI, INFO (red and amber) and LAN. Serial: WARNING: The serial port needs a TTL/RS-232 v3.3 level converter! The Serial setting is 115200-8-N-1. The SoC's serial port is right next to the MXIC FLASH chip. The board has a unpopulated 1x4 0.1" header for it. Use a multimeter to figure out the pinout! This board currently needs an additional u-boot image in order to boot properly. Booting with EVA isn't possible ATM. Install Procedure: 0. It's highly recommended to connect to the serial port. The serial settings are listed above. 1. install a u-boot image for AVM Fritz!Box 4040 (see <https://github.com/chunkeey/FritzBox-4040-UBOOT/releases> and <https://github.com/chunkeey/FritzBox-4040-UBOOT/blob/master/upload-to-f4040.sh>) 2. upload the initramfs.itb image via tftp (u-boot listens to 192.168.1.1 - use binary transfer mode!) 3. connect to the FB4040 and use sysupgrade sysupgrade.bin to install the image. Works: - Switch and Ethernet (99%) - Buttons (WLAN, WPS) - FLASH (1 x 32MiB NOR Chip) - WLAN2G and WLAN5G - CPUFREQ scaling - PRNG - serial - Crypto Accelerator - sysupgrade (Read the flash instructions to avoid bricking) - full LEDE Install (Read the flash instructions to avoid bricking) - LEDs (Power, WAN, Info (red and amber), LAN) The LEDs are connected to the QCA8075 LED ports. The AR40xx driver contains a gpio-controller to handle these special "GPIOs". - USB Both 3.0 and 2.0 ports - many packages from other ARMv7 boards (This does include the RaspberryPi Model 2!) - ... Not planned: - WAN<->LAN short-cut - Qualcomm Secure Execution Environment - ... Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John Crispin <john@phrozen.org>
2017-03-14 16:04:28 +00:00
define Device/netgear_r7500
$(call Device/DniImage)
DEVICE_DTS := qcom-ipq8064-r7500
KERNEL_SIZE := 4194304
NETGEAR_BOARD_ID := R7500
NETGEAR_HW_ID := 29764841+0+128+256+3x3+4x4
BLOCKSIZE := 128k
PAGESIZE := 2048
BOARD_NAME := r7500
SUPPORTED_DEVICES += r7500
DEVICE_TITLE := Netgear Nighthawk X4 R7500
DEVICE_PACKAGES := ath10k-firmware-qca988x
endef
TARGET_DEVICES += netgear_r7500
define Device/netgear_r7500v2
$(call Device/DniImage)
DEVICE_DTS := qcom-ipq8064-r7500v2
KERNEL_SIZE := 2097152
NETGEAR_BOARD_ID := R7500v2
NETGEAR_HW_ID := 29764958+0+128+512+3x3+4x4
BLOCKSIZE := 128k
PAGESIZE := 2048
BOARD_NAME := r7500v2
SUPPORTED_DEVICES += r7500v2
DEVICE_TITLE := Netgear Nighthawk X4 R7500v2
DEVICE_PACKAGES := ath10k-firmware-qca99x0 ath10k-firmware-qca988x
endef
TARGET_DEVICES += netgear_r7500v2
define Device/netgear_r7800
$(call Device/DniImage)
DEVICE_DTS := qcom-ipq8065-r7800
KERNEL_SIZE := 4194304
NETGEAR_BOARD_ID := R7800
NETGEAR_HW_ID := 29764958+0+128+512+4x4+4x4+cascade
BLOCKSIZE := 128k
PAGESIZE := 2048
BOARD_NAME := r7800
SUPPORTED_DEVICES += r7800
DEVICE_TITLE := Netgear Nighthawk X4S R7800
DEVICE_PACKAGES := ath10k-firmware-qca9984
endef
TARGET_DEVICES += netgear_r7800
define Device/qcom_ipq8064-ap148
$(call Device/FitImage)
$(call Device/UbiFit)
DEVICE_DTS := qcom-ipq8064-ap148
KERNEL_INSTALL := 1
BLOCKSIZE := 128k
PAGESIZE := 2048
BOARD_NAME := ap148
SUPPORTED_DEVICES += ap148
DEVICE_TITLE := Qualcomm AP148
DEVICE_PACKAGES := ath10k-firmware-qca99x0
endef
TARGET_DEVICES += qcom_ipq8064-ap148
define Device/qcom_ipq8064-ap148-legacy
$(call Device/LegacyImage)
$(call Device/UbiFit)
DEVICE_DTS := qcom-ipq8064-ap148
BLOCKSIZE := 128k
PAGESIZE := 2048
BOARD_NAME := ap148
SUPPORTED_DEVICES := qcom,ipq8064-ap148 ap148
DEVICE_TITLE := Qualcomm AP148 (legacy)
DEVICE_PACKAGES := ath10k-firmware-qca99x0
endef
TARGET_DEVICES += qcom_ipq8064-ap148-legacy
define Device/qcom_ipq8064-db149
$(call Device/FitImage)
DEVICE_DTS := qcom-ipq8064-db149
KERNEL_INSTALL := 1
BOARD_NAME := db149
DEVICE_TITLE := Qualcomm DB149
DEVICE_PACKAGES := ath10k-firmware-qca99x0
endef
TARGET_DEVICES += qcom_ipq8064-db149
define Device/tplink_c2600
$(call Device/TpSafeImage)
DEVICE_DTS := qcom-ipq8064-c2600
BLOCKSIZE := 128k
PAGESIZE := 2048
BOARD_NAME := c2600
SUPPORTED_DEVICES += c2600
TPLINK_BOARD_ID := C2600
DEVICE_TITLE := TP-Link Archer C2600
DEVICE_PACKAGES := ath10k-firmware-qca99x0
endef
TARGET_DEVICES += tplink_c2600
define Device/tplink_vr2600v
KERNEL_SUFFIX := -uImage
KERNEL = kernel-bin | append-dtb | uImage none
KERNEL_NAME := zImage
KERNEL_SIZE := 3145728
DEVICE_DTS := qcom-ipq8064-vr2600v
BLOCKSIZE := 128k
PAGESIZE := 2048
BOARD_NAME := vr2600v
SUPPORTED_DEVICES += vr2600v
DEVICE_TITLE := TP-Link Archer VR2600v
DEVICE_PACKAGES := ath10k-firmware-qca99x0
IMAGES := sysupgrade.bin
IMAGE/sysupgrade.bin := pad-extra 512 | append-kernel | pad-to $$$${KERNEL_SIZE} | append-rootfs | pad-rootfs | append-metadata
endef
TARGET_DEVICES += tplink_vr2600v
define Device/zyxel_nbg6817
DEVICE_DTS := qcom-ipq8065-nbg6817
KERNEL_SIZE := 4096k
BLOCKSIZE := 64k
BOARD_NAME := nbg6817
SUPPORTED_DEVICES += nbg6817
DEVICE_TITLE := ZyXEL NBG6817
DEVICE_PACKAGES := ath10k-firmware-qca9984 e2fsprogs kmod-fs-ext4 losetup
$(call Device/ZyXELImage)
endef
TARGET_DEVICES += zyxel_nbg6817
$(eval $(call BuildImage))