ExternalVendorCode/openwrt
1
0
Fork 0
mirror of https://github.com/openwrt/openwrt.git synced 2024-12-25 16:31:13 +00:00
Code Issues Actions Packages Projects Releases Wiki Activity
3cc08b5702
openwrt/target/linux/octeon/image/Makefile

76 lines
2.4 KiB
Makefile
Raw Normal View History

target: use SPDX license identifiers on Makefiles Use SPDX license tags to allow machines to check licenses. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-10 13:52:34 +00:00
# SPDX-License-Identifier: GPL-2.0-only
octeon: add support for the octeon mips64 SoC This is the SoC used be the ESR Lite made by ubnt.com Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 37684
2013-08-04 13:54:32 +00:00
#
# Copyright (C) 2009-2010 OpenWrt.org
target: use SPDX license identifiers on Makefiles Use SPDX license tags to allow machines to check licenses. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-10 13:52:34 +00:00
octeon: add support for the octeon mips64 SoC This is the SoC used be the ESR Lite made by ubnt.com Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 37684
2013-08-04 13:54:32 +00:00
include $(TOPDIR)/rules.mk
include $(INCLUDE_DIR)/image.mk
octeon: add support for Ubiquiti EdgeRouter 4 Ubiquiti EdgeRouter 4 is 4 port Octeon Cavium 7130 powered router. It has internal power supply and needs c13 power cord. There are three 10/100/1000 Mbps RJ45/Copper ports and one 1000 Mbps SFP port connected directly to a SoC. SoC: Octeon Cavium 7130 (Cavium 3) Clocked at 1000Mhz Memory: 1 GiB (SK hynix H5TQ4G63CFR-RDC × 2) DDR3, clocked at 533 Mhz (1066Mhz effective) Flash: - mtd: 8 MiB (Macronix MX25L6408EMI-12G) used for uboot/eeprom - emmc: 4 GiB (SanDisk SDIN7DP2-4G) used for kernel+rootfs Leds: 1x for power status (white/blue, controllable) and 4x for ethernet and sfp ports (no control over them) Buttons: 1x Reset (from SOC) Serial: 1x RJ45 port on front panel. 115200 baud, 8N1 (from SoC) USB: 1x USB3.0 on front panel (from SoC) MII: 1x QSGMII from SoC is used PHY: 1x Vitesse VSC8504 of which 4x ports is used All physical port numbers are properly mapped inside OS and named by lanX instead of ethX. There is also special purpose four(4) loopX ports available. That loopX ports are currently hardcoded by linux kernel and exact use case of them is currently unknown. We leave them to the linux kernel and octeon board defaults. All four (4) physical ports are connected to the same QSGMII. vsc8504 is used for phys and only 4, 5, 6 and 7 phys are used. Phy mapping: - Phy5 is connected to physical eth0 port - Phy6 is connected to physical eth1 port - Phy7 is connected to physical eth2 port - Phy4 is connected to physical eth3 port Why this device needs external dts: - faster boot time since need to initialize less device tree nodes. - to add actual indication with LED about boot/failure/upgrade. i.e. user could know when to enter failsafe mode or if upgrade is done - reset button support so user can reset their device in case off failure - sfp port indication in dmesg with information about sfp module it also indicates when module inserted or removed Octeon quirks: - There is no port status available before it interface brought up - SFP port can not be tied to actual phy due to octeon-ethernet state and currently we can only get reports a about SFP state in dmesg How to flash the firmware: - copy openwrt-octeon-ubnt_edgerouter-4-initramfs-kernel.bin and openwrt-octeon-ubnt_edgerouter-4-squashfs-sysupgrade.tar to USB flash drive that is formatted to vfat/fat32 - connect USB flash drive to edgerouter 4 front USB port - connect serial cable using front RJ45 port (115200 baud, 8N1) - connect power to cable to edgerouter 4 - connect terminal to the console to see uboot boot process - interrupt boot by pressing button(s) on your keyboard to log in to the uboot - detect usb connected flash drives by typing to the console: usb start - after drive is detected load initramfs+kernel to the memory by typing: fatload usb 0:1 0x20000000 openwrt-octeon-ubnt_edgerouter-4-initramfs-kernel.bin - after initramfs+kernel is loaded to the memory load it by typing: bootoctlinux 0 numcores=4 endbootargs mem=0 - boot process should finish and you will be greeted with console after pressing enter - create directory to mount usb flash drive to by typing: mkdir /tmp/sda - mount flash drive to that directory by typing: mount /dev/sda1 /tmp/sda - flash firmware to router internal storage by typing: sysupgrade /tmp/sda/openwrt-octeon-ubnt_edgerouter-4-squashfs-sysupgrade.tar - device will reboot and after it gets up you will have edgerouter 4 running openwrt Reviewed-by: Johannes Kimmel <fff@bareminimum.eu> Tested-by: Johannes Kimmel <fff@bareminimum.eu> Signed-off-by: Roman Kuzmitskii <damex.pp@icloud.com>
2020-10-22 21:20:05 +00:00
define Build/append-dtb-to-elf
$(TARGET_CROSS)objcopy --update-section .appended_dtb=$(KDIR)/image-$(DEVICE_DTS).dtb $@
endef
octeon: apply vendor_model scheme to device definition/image name This updates the device definition name for octeon target to provide more useful names for the images and be consistent with the increasing number of targets following that scheme. Since the target is not using device tree yet, this does not touch board_name and thus sets BOARD_NAME in image Makefile to ensure sysupgrade is still working. While at it, move Build block before Device blocks and remove trailing whitespace for CMDLINE. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-01-18 01:18:49 +00:00
define Build/strip-kernel
# Workaround pre-SDK-1.9.0 u-boot versions not handling the .notes section
$(TARGET_CROSS)strip -R .notes $@ -o $@.stripped && mv $@.stripped $@
endef
octeon: add support for Ubiquiti EdgeRouter 4 Ubiquiti EdgeRouter 4 is 4 port Octeon Cavium 7130 powered router. It has internal power supply and needs c13 power cord. There are three 10/100/1000 Mbps RJ45/Copper ports and one 1000 Mbps SFP port connected directly to a SoC. SoC: Octeon Cavium 7130 (Cavium 3) Clocked at 1000Mhz Memory: 1 GiB (SK hynix H5TQ4G63CFR-RDC × 2) DDR3, clocked at 533 Mhz (1066Mhz effective) Flash: - mtd: 8 MiB (Macronix MX25L6408EMI-12G) used for uboot/eeprom - emmc: 4 GiB (SanDisk SDIN7DP2-4G) used for kernel+rootfs Leds: 1x for power status (white/blue, controllable) and 4x for ethernet and sfp ports (no control over them) Buttons: 1x Reset (from SOC) Serial: 1x RJ45 port on front panel. 115200 baud, 8N1 (from SoC) USB: 1x USB3.0 on front panel (from SoC) MII: 1x QSGMII from SoC is used PHY: 1x Vitesse VSC8504 of which 4x ports is used All physical port numbers are properly mapped inside OS and named by lanX instead of ethX. There is also special purpose four(4) loopX ports available. That loopX ports are currently hardcoded by linux kernel and exact use case of them is currently unknown. We leave them to the linux kernel and octeon board defaults. All four (4) physical ports are connected to the same QSGMII. vsc8504 is used for phys and only 4, 5, 6 and 7 phys are used. Phy mapping: - Phy5 is connected to physical eth0 port - Phy6 is connected to physical eth1 port - Phy7 is connected to physical eth2 port - Phy4 is connected to physical eth3 port Why this device needs external dts: - faster boot time since need to initialize less device tree nodes. - to add actual indication with LED about boot/failure/upgrade. i.e. user could know when to enter failsafe mode or if upgrade is done - reset button support so user can reset their device in case off failure - sfp port indication in dmesg with information about sfp module it also indicates when module inserted or removed Octeon quirks: - There is no port status available before it interface brought up - SFP port can not be tied to actual phy due to octeon-ethernet state and currently we can only get reports a about SFP state in dmesg How to flash the firmware: - copy openwrt-octeon-ubnt_edgerouter-4-initramfs-kernel.bin and openwrt-octeon-ubnt_edgerouter-4-squashfs-sysupgrade.tar to USB flash drive that is formatted to vfat/fat32 - connect USB flash drive to edgerouter 4 front USB port - connect serial cable using front RJ45 port (115200 baud, 8N1) - connect power to cable to edgerouter 4 - connect terminal to the console to see uboot boot process - interrupt boot by pressing button(s) on your keyboard to log in to the uboot - detect usb connected flash drives by typing to the console: usb start - after drive is detected load initramfs+kernel to the memory by typing: fatload usb 0:1 0x20000000 openwrt-octeon-ubnt_edgerouter-4-initramfs-kernel.bin - after initramfs+kernel is loaded to the memory load it by typing: bootoctlinux 0 numcores=4 endbootargs mem=0 - boot process should finish and you will be greeted with console after pressing enter - create directory to mount usb flash drive to by typing: mkdir /tmp/sda - mount flash drive to that directory by typing: mount /dev/sda1 /tmp/sda - flash firmware to router internal storage by typing: sysupgrade /tmp/sda/openwrt-octeon-ubnt_edgerouter-4-squashfs-sysupgrade.tar - device will reboot and after it gets up you will have edgerouter 4 running openwrt Reviewed-by: Johannes Kimmel <fff@bareminimum.eu> Tested-by: Johannes Kimmel <fff@bareminimum.eu> Signed-off-by: Roman Kuzmitskii <damex.pp@icloud.com>
2020-10-22 21:20:05 +00:00
DTS_DIR := $(DTS_DIR)/cavium-octeon
octeon: convert to new image building code Signed-off-by: John Crispin <john@phrozen.org>
2016-05-15 07:44:34 +00:00
define Device/Default
PROFILES = Default $$(DEVICE_NAME)
KERNEL_NAME := vmlinux.elf
KERNEL_INITRAMFS_NAME := vmlinux-initramfs.elf
KERNEL := kernel-bin | strip-kernel | patch-cmdline
IMAGES := sysupgrade.tar
octeon: use new ext4/f2fs overlay support Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-09-08 12:46:49 +00:00
IMAGE/sysupgrade.tar/squashfs := append-rootfs | pad-extra 128k | sysupgrade-tar rootfs=$$$$@
build: rename sysupgrade-nand to sysupgrade-tar Now that the "sysupgrade-nand" step is used by non-NAND targets as well, rename it to "sysupgrade-tar" to make it more generic. Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2016-07-29 13:05:51 +00:00
IMAGE/sysupgrade.tar := sysupgrade-tar
octeon: fix imagebuilder Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 45821
2015-05-29 11:28:20 +00:00
endef
octeon: convert to new image building code Signed-off-by: John Crispin <john@phrozen.org>
2016-05-15 07:44:34 +00:00
define Device/generic
octeon: split up remaining DEVICE_TITLE DEVICE_TITLE is split up into DEVICE_VENDOR and DEVICE_MODEL Signed-off-by: Moritz Warning <moritzwarning@web.de>
2019-09-25 22:22:07 +00:00
DEVICE_VENDOR := Generic
DEVICE_MODEL := Octeon
octeon: convert to new image building code Signed-off-by: John Crispin <john@phrozen.org>
2016-05-15 07:44:34 +00:00
FILESYSTEMS := ext4
octeon: add er8 sysupgrade support Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 44902
2015-03-20 08:49:08 +00:00
endef
octeon: convert to new image building code Signed-off-by: John Crispin <john@phrozen.org>
2016-05-15 07:44:34 +00:00
TARGET_DEVICES += generic
octeon: add er8 sysupgrade support Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 44902
2015-03-20 08:49:08 +00:00
octeon: add support for Itus Shield Router Itus Networks Shield - 1Ghz dual-core mips64 / Cavium Octeon 3 SoC, 1Gb RAM, 4Gb eMMC,3 GbE 10/100/1000 ports Information regarding device can be found: https://deviwiki.com/wiki/Itus_Networks_Shield_Pro Installing OpenWrt on Itus Networks Shield: 1) Boot Shield 2) On device: mount /dev/mmcblk1p1 /mnt 3) scp openwrt-octeon-itus,shield-router-initramfs-kernel.bin to /mnt/ItusrouterImage 3a) Optionally: scp openwrt-octeon-itus,shield-router-initramfs-kernel.bin to /mnt/ItusgatewayImage to allow you to have an emergency recovery boot in the GATEWAY slot - this slot will have no permament storage and is used for emergency recovery only when booted in the (G)ateway position 4) On device: umount /mnt 5) reboot Once booted, run the sysupgrade via cli or luCi on the openwrt-octeon-itus,shield-router-squashfs-sysupgrade.tar file the mode you are running. Once rebooted, the system installation is complete. Your storage partition for the mode is inialized and set. Signed-off-by: Donald Hoskins <grommish@gmail.com> [cut out sysupgrade-* changes, move a few lines, drop case CVMX_BOARD_TYPE_ITUS_SHIELD] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-22 09:26:33 +00:00
ITUSROUTER_CMDLINE:=console=ttyS0,115200 root=/dev/mmcblk1p2 rootfstype=squashfs,ext4,f2fs rootwait
define Device/itus_shield-router
DEVICE_VENDOR := Itus Networks
DEVICE_MODEL := Shield Router
CMDLINE := $(ITUSROUTER_CMDLINE)
IMAGE/sysupgrade.tar/squashfs += | append-metadata
endef
TARGET_DEVICES += itus_shield-router
octeon: use new ext4/f2fs overlay support Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-09-08 12:46:49 +00:00
ER_CMDLINE:=-mtdparts=phys_mapped_flash:640k(boot0)ro,640k(boot1)ro,64k(eeprom)ro root=/dev/mmcblk0p2 rootfstype=squashfs,ext4 rootwait
octeon: apply vendor_model scheme to device definition/image name This updates the device definition name for octeon target to provide more useful names for the images and be consistent with the increasing number of targets following that scheme. Since the target is not using device tree yet, this does not touch board_name and thus sets BOARD_NAME in image Makefile to ensure sysupgrade is still working. While at it, move Build block before Device blocks and remove trailing whitespace for CMDLINE. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-01-18 01:18:49 +00:00
define Device/ubnt_edgerouter
octeon: split up DEVICE_TITLE Splits up DEVICE_TITLE into DEVICE_VENDOR, DEVICE_MODEL and DEVICE_VARIANT. Signed-off-by: Moritz Warning <moritzwarning@web.de>
2019-07-14 08:34:19 +00:00
DEVICE_VENDOR := Ubiquiti
DEVICE_MODEL := EdgeRouter
octeon: apply vendor_model scheme to device definition/image name This updates the device definition name for octeon target to provide more useful names for the images and be consistent with the increasing number of targets following that scheme. Since the target is not using device tree yet, this does not touch board_name and thus sets BOARD_NAME in image Makefile to ensure sysupgrade is still working. While at it, move Build block before Device blocks and remove trailing whitespace for CMDLINE. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-01-18 01:18:49 +00:00
BOARD_NAME := er
CMDLINE := $(ER_CMDLINE)
octeon: disable edgerouter image This patch disables the image for edgerouter devices by default, since it isn't able to boot at the moment. Currently the edgerouter image won't boot. Current kernels have an option CONFIG_CAVIUM_CN63XXP1 that needs to be enabled for this chip. If the kernel was compiled without this option, following message is displayed and the machine reboots: [ 36.778028] Kernel panic - not syncing: OCTEON II DCache prefetch workaround not in place (cfa0000c). [ 36.778028] Please build kernel with proper options (CONFIG_CAVIUM_CN63XXP1). [ 36.794398] Rebooting in 1 seconds.. This was last confirmed on 2020-10-29. The description of this option states, that enabling it will possibly cause performance issues on other chips. Signed-off-by: Johannes Kimmel <fff@bareminimum.eu>
2020-10-29 10:07:38 +00:00
DEFAULT := n
octeon: add er8 sysupgrade support Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 44902
2015-03-20 08:49:08 +00:00
endef
octeon: apply vendor_model scheme to device definition/image name This updates the device definition name for octeon target to provide more useful names for the images and be consistent with the increasing number of targets following that scheme. Since the target is not using device tree yet, this does not touch board_name and thus sets BOARD_NAME in image Makefile to ensure sysupgrade is still working. While at it, move Build block before Device blocks and remove trailing whitespace for CMDLINE. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-01-18 01:18:49 +00:00
TARGET_DEVICES += ubnt_edgerouter
octeon: add er8 sysupgrade support Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 44902
2015-03-20 08:49:08 +00:00
octeon: add support for Ubiquiti EdgeRouter 4 Ubiquiti EdgeRouter 4 is 4 port Octeon Cavium 7130 powered router. It has internal power supply and needs c13 power cord. There are three 10/100/1000 Mbps RJ45/Copper ports and one 1000 Mbps SFP port connected directly to a SoC. SoC: Octeon Cavium 7130 (Cavium 3) Clocked at 1000Mhz Memory: 1 GiB (SK hynix H5TQ4G63CFR-RDC × 2) DDR3, clocked at 533 Mhz (1066Mhz effective) Flash: - mtd: 8 MiB (Macronix MX25L6408EMI-12G) used for uboot/eeprom - emmc: 4 GiB (SanDisk SDIN7DP2-4G) used for kernel+rootfs Leds: 1x for power status (white/blue, controllable) and 4x for ethernet and sfp ports (no control over them) Buttons: 1x Reset (from SOC) Serial: 1x RJ45 port on front panel. 115200 baud, 8N1 (from SoC) USB: 1x USB3.0 on front panel (from SoC) MII: 1x QSGMII from SoC is used PHY: 1x Vitesse VSC8504 of which 4x ports is used All physical port numbers are properly mapped inside OS and named by lanX instead of ethX. There is also special purpose four(4) loopX ports available. That loopX ports are currently hardcoded by linux kernel and exact use case of them is currently unknown. We leave them to the linux kernel and octeon board defaults. All four (4) physical ports are connected to the same QSGMII. vsc8504 is used for phys and only 4, 5, 6 and 7 phys are used. Phy mapping: - Phy5 is connected to physical eth0 port - Phy6 is connected to physical eth1 port - Phy7 is connected to physical eth2 port - Phy4 is connected to physical eth3 port Why this device needs external dts: - faster boot time since need to initialize less device tree nodes. - to add actual indication with LED about boot/failure/upgrade. i.e. user could know when to enter failsafe mode or if upgrade is done - reset button support so user can reset their device in case off failure - sfp port indication in dmesg with information about sfp module it also indicates when module inserted or removed Octeon quirks: - There is no port status available before it interface brought up - SFP port can not be tied to actual phy due to octeon-ethernet state and currently we can only get reports a about SFP state in dmesg How to flash the firmware: - copy openwrt-octeon-ubnt_edgerouter-4-initramfs-kernel.bin and openwrt-octeon-ubnt_edgerouter-4-squashfs-sysupgrade.tar to USB flash drive that is formatted to vfat/fat32 - connect USB flash drive to edgerouter 4 front USB port - connect serial cable using front RJ45 port (115200 baud, 8N1) - connect power to cable to edgerouter 4 - connect terminal to the console to see uboot boot process - interrupt boot by pressing button(s) on your keyboard to log in to the uboot - detect usb connected flash drives by typing to the console: usb start - after drive is detected load initramfs+kernel to the memory by typing: fatload usb 0:1 0x20000000 openwrt-octeon-ubnt_edgerouter-4-initramfs-kernel.bin - after initramfs+kernel is loaded to the memory load it by typing: bootoctlinux 0 numcores=4 endbootargs mem=0 - boot process should finish and you will be greeted with console after pressing enter - create directory to mount usb flash drive to by typing: mkdir /tmp/sda - mount flash drive to that directory by typing: mount /dev/sda1 /tmp/sda - flash firmware to router internal storage by typing: sysupgrade /tmp/sda/openwrt-octeon-ubnt_edgerouter-4-squashfs-sysupgrade.tar - device will reboot and after it gets up you will have edgerouter 4 running openwrt Reviewed-by: Johannes Kimmel <fff@bareminimum.eu> Tested-by: Johannes Kimmel <fff@bareminimum.eu> Signed-off-by: Roman Kuzmitskii <damex.pp@icloud.com>
2020-10-22 21:20:05 +00:00
define Device/ubnt_edgerouter-4
DEVICE_VENDOR := Ubiquiti
DEVICE_MODEL := EdgeRouter 4
DEVICE_DTS := cn7130_ubnt_edgerouter-4
DEVICE_PACKAGES += kmod-gpio-button-hotplug kmod-leds-gpio kmod-of-mdio kmod-sfp kmod-usb3 kmod-usb-dwc3 kmod-usb-storage-uas
KERNEL := kernel-bin | patch-cmdline | append-dtb-to-elf
KERNEL_DEPENDS := $$(wildcard $(DTS_DIR)/$(DEVICE_DTS).dts)
CMDLINE := root=/dev/mmcblk0p2 rootfstype=squashfs,ext4 rootwait
endef
TARGET_DEVICES += ubnt_edgerouter-4
octeon: fix mtd partitions for erlite on cmdline erlite mtdparts exposes boot0, boot1 and eeprom regions as read/write. this patch adds readonly flags, so these regions can't be modified. same as it is already for ER profile. Signed-off-by: Jiri Kastner <cz172638@gmail.com>
2017-01-18 09:45:23 +00:00
ERLITE_CMDLINE:=-mtdparts=phys_mapped_flash:512k(boot0)ro,512k(boot1)ro,64k(eeprom)ro root=/dev/sda2 rootfstype=squashfs,ext4 rootwait
octeon: apply vendor_model scheme to device definition/image name This updates the device definition name for octeon target to provide more useful names for the images and be consistent with the increasing number of targets following that scheme. Since the target is not using device tree yet, this does not touch board_name and thus sets BOARD_NAME in image Makefile to ensure sysupgrade is still working. While at it, move Build block before Device blocks and remove trailing whitespace for CMDLINE. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-01-18 01:18:49 +00:00
define Device/ubnt_edgerouter-lite
octeon: split up DEVICE_TITLE Splits up DEVICE_TITLE into DEVICE_VENDOR, DEVICE_MODEL and DEVICE_VARIANT. Signed-off-by: Moritz Warning <moritzwarning@web.de>
2019-07-14 08:34:19 +00:00
DEVICE_VENDOR := Ubiquiti
DEVICE_MODEL := EdgeRouter Lite
octeon: apply vendor_model scheme to device definition/image name This updates the device definition name for octeon target to provide more useful names for the images and be consistent with the increasing number of targets following that scheme. Since the target is not using device tree yet, this does not touch board_name and thus sets BOARD_NAME in image Makefile to ensure sysupgrade is still working. While at it, move Build block before Device blocks and remove trailing whitespace for CMDLINE. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-01-18 01:18:49 +00:00
BOARD_NAME := erlite
CMDLINE := $(ERLITE_CMDLINE)
octeon: add support for the octeon mips64 SoC This is the SoC used be the ESR Lite made by ubnt.com Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 37684
2013-08-04 13:54:32 +00:00
endef
octeon: apply vendor_model scheme to device definition/image name This updates the device definition name for octeon target to provide more useful names for the images and be consistent with the increasing number of targets following that scheme. Since the target is not using device tree yet, this does not touch board_name and thus sets BOARD_NAME in image Makefile to ensure sysupgrade is still working. While at it, move Build block before Device blocks and remove trailing whitespace for CMDLINE. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-01-18 01:18:49 +00:00
TARGET_DEVICES += ubnt_edgerouter-lite
octeon: add support for the octeon mips64 SoC This is the SoC used be the ESR Lite made by ubnt.com Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 37684
2013-08-04 13:54:32 +00:00
$(eval $(call BuildImage))
Reference in New Issue Copy Permalink