openwrt/target/linux/ath79/dts/qca9531_glinet_gl-e750.dts

141 lines
2.0 KiB
Plaintext
Raw Normal View History

ath79: add support for gl-e750 The gl-e750 is a portable travel router that gives you safe access to the internet while traveling. Specifications: - SoC: Qualcomm Atheros AR9531 (650MHz) - RAM: 128 MB DDR2 - Flash: 16 MB SPI NOR (W25Q128FVSG) + 128 MB SPI NAND (GD5F1GQ4UFYIG) - Ethernet: 10/100: 1xLAN - Wireless: QCA9531 2.4GHz (bgn) + QCA9887 5GHz (ac) - USB: 1x USB 2.0 port - Switch: 1x switch - Button: 1x reset button - OLED Screen: 128*64 px MAC addresses based on vendor firmware: LAN *:a0 art 0x0 2.4GHz *:a1 art 0x1002 5GHz *:a2 art calculated from art 0x0 + 2 Flash firmware: Since openwrt's kernel already exceeds 2MB, upgrading from the official version of GL-inet (v3.100) using the sysupgrade command will break the kernel image. Users who are using version 3.100 can only upgrade via uboot. The official guidance for GL-inet is as follows: https://docs.gl-inet.com/en/3/troubleshooting/debrick/ In the future, GL-inet will modify the firmware to support the sysupgrade command, so users will be able to upgrade directly with the sysupgrade command in future releases. OLED screen control: OLED controller is connected to QCA9531 through serial port, and can send instructions to OLED controller directly through serial port. Refer to the links below for a list of supported instructions: https://github.com/gl-inet/GL-E750-MCU-instruction Signed-off-by: Luochongjun <luochongjun@gl-inet.com> [fix alphabetic sorting in 10-fix-wifi-mac, drop check-kernel-size] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-11 12:58:47 +00:00
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/dts-v1/;
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include "qca953x.dtsi"
/ {
compatible = "glinet,gl-e750", "qca,qca9531";
model = "GL.iNet GL-E750";
aliases {
label-mac-device = &eth0;
};
keys {
compatible = "gpio-keys";
pinctrl-names = "default";
pinctrl-0 = <&jtag_disable_pins>;
reset {
label = "reset";
linux,code = <KEY_RESTART>;
gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
};
switch {
label = "switch";
linux,code = <BTN_0>;
gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
};
};
gpio-export {
compatible = "gpio-export";
gpio_lte_power {
gpio-export,name = "lte_power";
gpio-export,output = <1>;
gpios = <&gpio 0 GPIO_ACTIVE_HIGH>;
};
};
};
&pcie0 {
status = "okay";
};
&uart {
status = "okay";
};
&usb0 {
status = "okay";
};
&usb_phy {
status = "okay";
};
&spi {
status = "okay";
num-cs = <2>;
flash@0 {
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <25000000>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "u-boot";
reg = <0x0 0x40000>;
read-only;
};
partition@40000 {
label = "u-boot-env";
reg = <0x40000 0x10000>;
};
art: partition@50000 {
label = "art";
reg = <0x50000 0x10000>;
read-only;
};
partition@60000 {
label = "kernel";
reg = <0x60000 0x400000>;
};
partition@460000 {
label = "reserved";
reg = <0x460000 0xba0000>;
};
};
};
flash@1 {
compatible = "spi-nand";
reg = <1>;
spi-max-frequency = <25000000>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "ubi";
reg = <0x0 0x8000000>;
};
};
};
};
&eth0 {
status = "okay";
phy-handle = <&swphy4>;
mtd-mac-address = <&art 0x0>;
ath79: add support for gl-e750 The gl-e750 is a portable travel router that gives you safe access to the internet while traveling. Specifications: - SoC: Qualcomm Atheros AR9531 (650MHz) - RAM: 128 MB DDR2 - Flash: 16 MB SPI NOR (W25Q128FVSG) + 128 MB SPI NAND (GD5F1GQ4UFYIG) - Ethernet: 10/100: 1xLAN - Wireless: QCA9531 2.4GHz (bgn) + QCA9887 5GHz (ac) - USB: 1x USB 2.0 port - Switch: 1x switch - Button: 1x reset button - OLED Screen: 128*64 px MAC addresses based on vendor firmware: LAN *:a0 art 0x0 2.4GHz *:a1 art 0x1002 5GHz *:a2 art calculated from art 0x0 + 2 Flash firmware: Since openwrt's kernel already exceeds 2MB, upgrading from the official version of GL-inet (v3.100) using the sysupgrade command will break the kernel image. Users who are using version 3.100 can only upgrade via uboot. The official guidance for GL-inet is as follows: https://docs.gl-inet.com/en/3/troubleshooting/debrick/ In the future, GL-inet will modify the firmware to support the sysupgrade command, so users will be able to upgrade directly with the sysupgrade command in future releases. OLED screen control: OLED controller is connected to QCA9531 through serial port, and can send instructions to OLED controller directly through serial port. Refer to the links below for a list of supported instructions: https://github.com/gl-inet/GL-E750-MCU-instruction Signed-off-by: Luochongjun <luochongjun@gl-inet.com> [fix alphabetic sorting in 10-fix-wifi-mac, drop check-kernel-size] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-11 12:58:47 +00:00
};
&eth1 {
compatible = "syscon", "simple-mfd";
};
&wmac {
status = "okay";
mtd-cal-data = <&art 0x1000>;
};