openwrt/target/linux/ramips/dts/mt7621_edimax_re23s.dts

180 lines
3.0 KiB
Plaintext
Raw Normal View History

ramips: add support for Edimax Gemini RE23S Hardware -------- SoC: Mediatek MT7621AT (880 MHz, 2 cores 4 threads) RAM: 128MB FLASH: 16MB NOR (Macronix MX25L12805D) ETH: 1x 10/100/1000 Mbps Ethernet (MT7530) WIFI: - 2.4GHz: 1x MT7615 (4x4:4) - 5GHz: 1x MT7615 (4x4:4) - 4 antennas: 2 external detachable and 2 internal BTN: - 1x Reset button - 1x WPS button LEDS: - 1x Green led (Power) - 1x Green-Amber-Red led (Wifi) UART: - 57600-8-N-1 Everything works correctly. Installation ------------ Flash the factory image directly from OEM web interface. (You can login using these credentials: admin/1234) Restore OEM Firmware -------------------- Flash the OEM "bin" firmware directly from LUCI. The firmware is downloadable from the OEM web page. Warning: Remember to not keep settings! Warning2: Remember to force the flash. Restoring procedure tested with RE23_1.08.bin MAC addresses ------------- factory 0x4 *:24 factory 0x8004 *:25 Cimage 0x07 *:24 Cimage 0x0D *:24 Cimage 0x13 *:24 Cimage 0x19 *:25 No other addresses were found in factory partition. Since the label contains both the 2.4GHz and 5GHz mac address I decided to set the 5GHz one as label-mac-device. Moreover it also corresponds to the lan mac address. Notes ----- The wifi led in the OEM firmware changes colour depending on the signal strength. This can be done in OpenWrt but just for one interface. So for now will not be any default action for this led. If you want to open the case, pay attention to the antenna placed on the bottom part of the front cover. The wire is a bit short and it breaks easily. (I broke it) Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com> [fix two typos and add extended MAC address section to commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-19 23:27:56 +00:00
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
#include "mt7621.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include <dt-bindings/mtd/partitions/uimage.h>
ramips: add support for Edimax Gemini RE23S Hardware -------- SoC: Mediatek MT7621AT (880 MHz, 2 cores 4 threads) RAM: 128MB FLASH: 16MB NOR (Macronix MX25L12805D) ETH: 1x 10/100/1000 Mbps Ethernet (MT7530) WIFI: - 2.4GHz: 1x MT7615 (4x4:4) - 5GHz: 1x MT7615 (4x4:4) - 4 antennas: 2 external detachable and 2 internal BTN: - 1x Reset button - 1x WPS button LEDS: - 1x Green led (Power) - 1x Green-Amber-Red led (Wifi) UART: - 57600-8-N-1 Everything works correctly. Installation ------------ Flash the factory image directly from OEM web interface. (You can login using these credentials: admin/1234) Restore OEM Firmware -------------------- Flash the OEM "bin" firmware directly from LUCI. The firmware is downloadable from the OEM web page. Warning: Remember to not keep settings! Warning2: Remember to force the flash. Restoring procedure tested with RE23_1.08.bin MAC addresses ------------- factory 0x4 *:24 factory 0x8004 *:25 Cimage 0x07 *:24 Cimage 0x0D *:24 Cimage 0x13 *:24 Cimage 0x19 *:25 No other addresses were found in factory partition. Since the label contains both the 2.4GHz and 5GHz mac address I decided to set the 5GHz one as label-mac-device. Moreover it also corresponds to the lan mac address. Notes ----- The wifi led in the OEM firmware changes colour depending on the signal strength. This can be done in OpenWrt but just for one interface. So for now will not be any default action for this led. If you want to open the case, pay attention to the antenna placed on the bottom part of the front cover. The wire is a bit short and it breaks easily. (I broke it) Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com> [fix two typos and add extended MAC address section to commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-19 23:27:56 +00:00
/ {
compatible = "edimax,re23s", "mediatek,mt7621-soc";
model = "Edimax RE23S";
aliases {
led-boot = &led_power;
led-failsafe = &led_wifi_red;
led-running = &led_power;
led-upgrade = &led_power;
label-mac-device = &gmac0;
};
leds {
compatible = "gpio-leds";
led_power: power {
label = "green:power";
ramips: add support for Edimax Gemini RE23S Hardware -------- SoC: Mediatek MT7621AT (880 MHz, 2 cores 4 threads) RAM: 128MB FLASH: 16MB NOR (Macronix MX25L12805D) ETH: 1x 10/100/1000 Mbps Ethernet (MT7530) WIFI: - 2.4GHz: 1x MT7615 (4x4:4) - 5GHz: 1x MT7615 (4x4:4) - 4 antennas: 2 external detachable and 2 internal BTN: - 1x Reset button - 1x WPS button LEDS: - 1x Green led (Power) - 1x Green-Amber-Red led (Wifi) UART: - 57600-8-N-1 Everything works correctly. Installation ------------ Flash the factory image directly from OEM web interface. (You can login using these credentials: admin/1234) Restore OEM Firmware -------------------- Flash the OEM "bin" firmware directly from LUCI. The firmware is downloadable from the OEM web page. Warning: Remember to not keep settings! Warning2: Remember to force the flash. Restoring procedure tested with RE23_1.08.bin MAC addresses ------------- factory 0x4 *:24 factory 0x8004 *:25 Cimage 0x07 *:24 Cimage 0x0D *:24 Cimage 0x13 *:24 Cimage 0x19 *:25 No other addresses were found in factory partition. Since the label contains both the 2.4GHz and 5GHz mac address I decided to set the 5GHz one as label-mac-device. Moreover it also corresponds to the lan mac address. Notes ----- The wifi led in the OEM firmware changes colour depending on the signal strength. This can be done in OpenWrt but just for one interface. So for now will not be any default action for this led. If you want to open the case, pay attention to the antenna placed on the bottom part of the front cover. The wire is a bit short and it breaks easily. (I broke it) Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com> [fix two typos and add extended MAC address section to commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-19 23:27:56 +00:00
gpios = <&gpio 13 GPIO_ACTIVE_HIGH>;
};
wifi_green {
label = "green:wifi";
ramips: add support for Edimax Gemini RE23S Hardware -------- SoC: Mediatek MT7621AT (880 MHz, 2 cores 4 threads) RAM: 128MB FLASH: 16MB NOR (Macronix MX25L12805D) ETH: 1x 10/100/1000 Mbps Ethernet (MT7530) WIFI: - 2.4GHz: 1x MT7615 (4x4:4) - 5GHz: 1x MT7615 (4x4:4) - 4 antennas: 2 external detachable and 2 internal BTN: - 1x Reset button - 1x WPS button LEDS: - 1x Green led (Power) - 1x Green-Amber-Red led (Wifi) UART: - 57600-8-N-1 Everything works correctly. Installation ------------ Flash the factory image directly from OEM web interface. (You can login using these credentials: admin/1234) Restore OEM Firmware -------------------- Flash the OEM "bin" firmware directly from LUCI. The firmware is downloadable from the OEM web page. Warning: Remember to not keep settings! Warning2: Remember to force the flash. Restoring procedure tested with RE23_1.08.bin MAC addresses ------------- factory 0x4 *:24 factory 0x8004 *:25 Cimage 0x07 *:24 Cimage 0x0D *:24 Cimage 0x13 *:24 Cimage 0x19 *:25 No other addresses were found in factory partition. Since the label contains both the 2.4GHz and 5GHz mac address I decided to set the 5GHz one as label-mac-device. Moreover it also corresponds to the lan mac address. Notes ----- The wifi led in the OEM firmware changes colour depending on the signal strength. This can be done in OpenWrt but just for one interface. So for now will not be any default action for this led. If you want to open the case, pay attention to the antenna placed on the bottom part of the front cover. The wire is a bit short and it breaks easily. (I broke it) Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com> [fix two typos and add extended MAC address section to commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-19 23:27:56 +00:00
gpios = <&gpio 12 GPIO_ACTIVE_HIGH>;
};
wifi_amber {
label = "amber:wifi";
ramips: add support for Edimax Gemini RE23S Hardware -------- SoC: Mediatek MT7621AT (880 MHz, 2 cores 4 threads) RAM: 128MB FLASH: 16MB NOR (Macronix MX25L12805D) ETH: 1x 10/100/1000 Mbps Ethernet (MT7530) WIFI: - 2.4GHz: 1x MT7615 (4x4:4) - 5GHz: 1x MT7615 (4x4:4) - 4 antennas: 2 external detachable and 2 internal BTN: - 1x Reset button - 1x WPS button LEDS: - 1x Green led (Power) - 1x Green-Amber-Red led (Wifi) UART: - 57600-8-N-1 Everything works correctly. Installation ------------ Flash the factory image directly from OEM web interface. (You can login using these credentials: admin/1234) Restore OEM Firmware -------------------- Flash the OEM "bin" firmware directly from LUCI. The firmware is downloadable from the OEM web page. Warning: Remember to not keep settings! Warning2: Remember to force the flash. Restoring procedure tested with RE23_1.08.bin MAC addresses ------------- factory 0x4 *:24 factory 0x8004 *:25 Cimage 0x07 *:24 Cimage 0x0D *:24 Cimage 0x13 *:24 Cimage 0x19 *:25 No other addresses were found in factory partition. Since the label contains both the 2.4GHz and 5GHz mac address I decided to set the 5GHz one as label-mac-device. Moreover it also corresponds to the lan mac address. Notes ----- The wifi led in the OEM firmware changes colour depending on the signal strength. This can be done in OpenWrt but just for one interface. So for now will not be any default action for this led. If you want to open the case, pay attention to the antenna placed on the bottom part of the front cover. The wire is a bit short and it breaks easily. (I broke it) Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com> [fix two typos and add extended MAC address section to commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-19 23:27:56 +00:00
gpios = <&gpio 7 GPIO_ACTIVE_HIGH>;
};
led_wifi_red: wifi_red {
label = "red:wifi";
ramips: add support for Edimax Gemini RE23S Hardware -------- SoC: Mediatek MT7621AT (880 MHz, 2 cores 4 threads) RAM: 128MB FLASH: 16MB NOR (Macronix MX25L12805D) ETH: 1x 10/100/1000 Mbps Ethernet (MT7530) WIFI: - 2.4GHz: 1x MT7615 (4x4:4) - 5GHz: 1x MT7615 (4x4:4) - 4 antennas: 2 external detachable and 2 internal BTN: - 1x Reset button - 1x WPS button LEDS: - 1x Green led (Power) - 1x Green-Amber-Red led (Wifi) UART: - 57600-8-N-1 Everything works correctly. Installation ------------ Flash the factory image directly from OEM web interface. (You can login using these credentials: admin/1234) Restore OEM Firmware -------------------- Flash the OEM "bin" firmware directly from LUCI. The firmware is downloadable from the OEM web page. Warning: Remember to not keep settings! Warning2: Remember to force the flash. Restoring procedure tested with RE23_1.08.bin MAC addresses ------------- factory 0x4 *:24 factory 0x8004 *:25 Cimage 0x07 *:24 Cimage 0x0D *:24 Cimage 0x13 *:24 Cimage 0x19 *:25 No other addresses were found in factory partition. Since the label contains both the 2.4GHz and 5GHz mac address I decided to set the 5GHz one as label-mac-device. Moreover it also corresponds to the lan mac address. Notes ----- The wifi led in the OEM firmware changes colour depending on the signal strength. This can be done in OpenWrt but just for one interface. So for now will not be any default action for this led. If you want to open the case, pay attention to the antenna placed on the bottom part of the front cover. The wire is a bit short and it breaks easily. (I broke it) Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com> [fix two typos and add extended MAC address section to commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-19 23:27:56 +00:00
gpios = <&gpio 6 GPIO_ACTIVE_HIGH>;
};
};
keys {
compatible = "gpio-keys";
reset {
label = "reset";
gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
linux,code = <KEY_RESTART>;
};
wps {
label = "wps";
gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
linux,code = <KEY_WPS_BUTTON>;
};
};
};
&spi0 {
status = "okay";
flash@0 {
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <50000000>;
m25p,fast-read;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "bootloader";
reg = <0x0 0x30000>;
read-only;
};
partition@30000 {
label = "config";
reg = <0x30000 0x10000>;
read-only;
};
factory: partition@40000 {
compatible = "nvmem-cells";
ramips: add support for Edimax Gemini RE23S Hardware -------- SoC: Mediatek MT7621AT (880 MHz, 2 cores 4 threads) RAM: 128MB FLASH: 16MB NOR (Macronix MX25L12805D) ETH: 1x 10/100/1000 Mbps Ethernet (MT7530) WIFI: - 2.4GHz: 1x MT7615 (4x4:4) - 5GHz: 1x MT7615 (4x4:4) - 4 antennas: 2 external detachable and 2 internal BTN: - 1x Reset button - 1x WPS button LEDS: - 1x Green led (Power) - 1x Green-Amber-Red led (Wifi) UART: - 57600-8-N-1 Everything works correctly. Installation ------------ Flash the factory image directly from OEM web interface. (You can login using these credentials: admin/1234) Restore OEM Firmware -------------------- Flash the OEM "bin" firmware directly from LUCI. The firmware is downloadable from the OEM web page. Warning: Remember to not keep settings! Warning2: Remember to force the flash. Restoring procedure tested with RE23_1.08.bin MAC addresses ------------- factory 0x4 *:24 factory 0x8004 *:25 Cimage 0x07 *:24 Cimage 0x0D *:24 Cimage 0x13 *:24 Cimage 0x19 *:25 No other addresses were found in factory partition. Since the label contains both the 2.4GHz and 5GHz mac address I decided to set the 5GHz one as label-mac-device. Moreover it also corresponds to the lan mac address. Notes ----- The wifi led in the OEM firmware changes colour depending on the signal strength. This can be done in OpenWrt but just for one interface. So for now will not be any default action for this led. If you want to open the case, pay attention to the antenna placed on the bottom part of the front cover. The wire is a bit short and it breaks easily. (I broke it) Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com> [fix two typos and add extended MAC address section to commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-19 23:27:56 +00:00
label = "factory";
reg = <0x40000 0x10000>;
#address-cells = <1>;
#size-cells = <1>;
ramips: add support for Edimax Gemini RE23S Hardware -------- SoC: Mediatek MT7621AT (880 MHz, 2 cores 4 threads) RAM: 128MB FLASH: 16MB NOR (Macronix MX25L12805D) ETH: 1x 10/100/1000 Mbps Ethernet (MT7530) WIFI: - 2.4GHz: 1x MT7615 (4x4:4) - 5GHz: 1x MT7615 (4x4:4) - 4 antennas: 2 external detachable and 2 internal BTN: - 1x Reset button - 1x WPS button LEDS: - 1x Green led (Power) - 1x Green-Amber-Red led (Wifi) UART: - 57600-8-N-1 Everything works correctly. Installation ------------ Flash the factory image directly from OEM web interface. (You can login using these credentials: admin/1234) Restore OEM Firmware -------------------- Flash the OEM "bin" firmware directly from LUCI. The firmware is downloadable from the OEM web page. Warning: Remember to not keep settings! Warning2: Remember to force the flash. Restoring procedure tested with RE23_1.08.bin MAC addresses ------------- factory 0x4 *:24 factory 0x8004 *:25 Cimage 0x07 *:24 Cimage 0x0D *:24 Cimage 0x13 *:24 Cimage 0x19 *:25 No other addresses were found in factory partition. Since the label contains both the 2.4GHz and 5GHz mac address I decided to set the 5GHz one as label-mac-device. Moreover it also corresponds to the lan mac address. Notes ----- The wifi led in the OEM firmware changes colour depending on the signal strength. This can be done in OpenWrt but just for one interface. So for now will not be any default action for this led. If you want to open the case, pay attention to the antenna placed on the bottom part of the front cover. The wire is a bit short and it breaks easily. (I broke it) Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com> [fix two typos and add extended MAC address section to commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-19 23:27:56 +00:00
read-only;
eeprom_factory_0: eeprom@0 {
reg = <0x0 0x4da8>;
};
eeprom_factory_8000: eeprom@8000 {
reg = <0x8000 0x4da8>;
};
macaddr_factory_8004: macaddr@8004 {
reg = <0x8004 0x6>;
};
ramips: add support for Edimax Gemini RE23S Hardware -------- SoC: Mediatek MT7621AT (880 MHz, 2 cores 4 threads) RAM: 128MB FLASH: 16MB NOR (Macronix MX25L12805D) ETH: 1x 10/100/1000 Mbps Ethernet (MT7530) WIFI: - 2.4GHz: 1x MT7615 (4x4:4) - 5GHz: 1x MT7615 (4x4:4) - 4 antennas: 2 external detachable and 2 internal BTN: - 1x Reset button - 1x WPS button LEDS: - 1x Green led (Power) - 1x Green-Amber-Red led (Wifi) UART: - 57600-8-N-1 Everything works correctly. Installation ------------ Flash the factory image directly from OEM web interface. (You can login using these credentials: admin/1234) Restore OEM Firmware -------------------- Flash the OEM "bin" firmware directly from LUCI. The firmware is downloadable from the OEM web page. Warning: Remember to not keep settings! Warning2: Remember to force the flash. Restoring procedure tested with RE23_1.08.bin MAC addresses ------------- factory 0x4 *:24 factory 0x8004 *:25 Cimage 0x07 *:24 Cimage 0x0D *:24 Cimage 0x13 *:24 Cimage 0x19 *:25 No other addresses were found in factory partition. Since the label contains both the 2.4GHz and 5GHz mac address I decided to set the 5GHz one as label-mac-device. Moreover it also corresponds to the lan mac address. Notes ----- The wifi led in the OEM firmware changes colour depending on the signal strength. This can be done in OpenWrt but just for one interface. So for now will not be any default action for this led. If you want to open the case, pay attention to the antenna placed on the bottom part of the front cover. The wire is a bit short and it breaks easily. (I broke it) Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com> [fix two typos and add extended MAC address section to commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-19 23:27:56 +00:00
};
partition@50000 {
label = "cimage";
reg = <0x50000 0x20000>;
read-only;
};
partition@70000 {
compatible = "openwrt,uimage", "denx,uimage";
openwrt,offset = <FW_EDIMAX_OFFSET>;
openwrt,partition-magic = <FW_MAGIC_EDIMAX>;
ramips: add support for Edimax Gemini RE23S Hardware -------- SoC: Mediatek MT7621AT (880 MHz, 2 cores 4 threads) RAM: 128MB FLASH: 16MB NOR (Macronix MX25L12805D) ETH: 1x 10/100/1000 Mbps Ethernet (MT7530) WIFI: - 2.4GHz: 1x MT7615 (4x4:4) - 5GHz: 1x MT7615 (4x4:4) - 4 antennas: 2 external detachable and 2 internal BTN: - 1x Reset button - 1x WPS button LEDS: - 1x Green led (Power) - 1x Green-Amber-Red led (Wifi) UART: - 57600-8-N-1 Everything works correctly. Installation ------------ Flash the factory image directly from OEM web interface. (You can login using these credentials: admin/1234) Restore OEM Firmware -------------------- Flash the OEM "bin" firmware directly from LUCI. The firmware is downloadable from the OEM web page. Warning: Remember to not keep settings! Warning2: Remember to force the flash. Restoring procedure tested with RE23_1.08.bin MAC addresses ------------- factory 0x4 *:24 factory 0x8004 *:25 Cimage 0x07 *:24 Cimage 0x0D *:24 Cimage 0x13 *:24 Cimage 0x19 *:25 No other addresses were found in factory partition. Since the label contains both the 2.4GHz and 5GHz mac address I decided to set the 5GHz one as label-mac-device. Moreover it also corresponds to the lan mac address. Notes ----- The wifi led in the OEM firmware changes colour depending on the signal strength. This can be done in OpenWrt but just for one interface. So for now will not be any default action for this led. If you want to open the case, pay attention to the antenna placed on the bottom part of the front cover. The wire is a bit short and it breaks easily. (I broke it) Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com> [fix two typos and add extended MAC address section to commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-19 23:27:56 +00:00
label = "firmware";
reg = <0x70000 0xf50000>;
};
partition@fc0000 {
label = "freespace";
reg = <0xfc0000 0x40000>;
read-only;
};
};
};
};
&pcie {
status = "okay";
};
&pcie0 {
wifi@0,0 {
compatible = "mediatek,mt76";
reg = <0x0000 0 0 0 0>;
nvmem-cells = <&eeprom_factory_0>;
nvmem-cell-names = "eeprom";
ramips: add support for Edimax Gemini RE23S Hardware -------- SoC: Mediatek MT7621AT (880 MHz, 2 cores 4 threads) RAM: 128MB FLASH: 16MB NOR (Macronix MX25L12805D) ETH: 1x 10/100/1000 Mbps Ethernet (MT7530) WIFI: - 2.4GHz: 1x MT7615 (4x4:4) - 5GHz: 1x MT7615 (4x4:4) - 4 antennas: 2 external detachable and 2 internal BTN: - 1x Reset button - 1x WPS button LEDS: - 1x Green led (Power) - 1x Green-Amber-Red led (Wifi) UART: - 57600-8-N-1 Everything works correctly. Installation ------------ Flash the factory image directly from OEM web interface. (You can login using these credentials: admin/1234) Restore OEM Firmware -------------------- Flash the OEM "bin" firmware directly from LUCI. The firmware is downloadable from the OEM web page. Warning: Remember to not keep settings! Warning2: Remember to force the flash. Restoring procedure tested with RE23_1.08.bin MAC addresses ------------- factory 0x4 *:24 factory 0x8004 *:25 Cimage 0x07 *:24 Cimage 0x0D *:24 Cimage 0x13 *:24 Cimage 0x19 *:25 No other addresses were found in factory partition. Since the label contains both the 2.4GHz and 5GHz mac address I decided to set the 5GHz one as label-mac-device. Moreover it also corresponds to the lan mac address. Notes ----- The wifi led in the OEM firmware changes colour depending on the signal strength. This can be done in OpenWrt but just for one interface. So for now will not be any default action for this led. If you want to open the case, pay attention to the antenna placed on the bottom part of the front cover. The wire is a bit short and it breaks easily. (I broke it) Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com> [fix two typos and add extended MAC address section to commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-19 23:27:56 +00:00
ieee80211-freq-limit = <2400000 2500000>;
};
};
&pcie1 {
wifi@0,0 {
compatible = "mediatek,mt76";
reg = <0x0000 0 0 0 0>;
nvmem-cells = <&eeprom_factory_8000>;
nvmem-cell-names = "eeprom";
ramips: add support for Edimax Gemini RE23S Hardware -------- SoC: Mediatek MT7621AT (880 MHz, 2 cores 4 threads) RAM: 128MB FLASH: 16MB NOR (Macronix MX25L12805D) ETH: 1x 10/100/1000 Mbps Ethernet (MT7530) WIFI: - 2.4GHz: 1x MT7615 (4x4:4) - 5GHz: 1x MT7615 (4x4:4) - 4 antennas: 2 external detachable and 2 internal BTN: - 1x Reset button - 1x WPS button LEDS: - 1x Green led (Power) - 1x Green-Amber-Red led (Wifi) UART: - 57600-8-N-1 Everything works correctly. Installation ------------ Flash the factory image directly from OEM web interface. (You can login using these credentials: admin/1234) Restore OEM Firmware -------------------- Flash the OEM "bin" firmware directly from LUCI. The firmware is downloadable from the OEM web page. Warning: Remember to not keep settings! Warning2: Remember to force the flash. Restoring procedure tested with RE23_1.08.bin MAC addresses ------------- factory 0x4 *:24 factory 0x8004 *:25 Cimage 0x07 *:24 Cimage 0x0D *:24 Cimage 0x13 *:24 Cimage 0x19 *:25 No other addresses were found in factory partition. Since the label contains both the 2.4GHz and 5GHz mac address I decided to set the 5GHz one as label-mac-device. Moreover it also corresponds to the lan mac address. Notes ----- The wifi led in the OEM firmware changes colour depending on the signal strength. This can be done in OpenWrt but just for one interface. So for now will not be any default action for this led. If you want to open the case, pay attention to the antenna placed on the bottom part of the front cover. The wire is a bit short and it breaks easily. (I broke it) Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com> [fix two typos and add extended MAC address section to commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-19 23:27:56 +00:00
ieee80211-freq-limit = <5000000 6000000>;
};
};
&gmac0 {
nvmem-cells = <&macaddr_factory_8004>;
nvmem-cell-names = "mac-address";
ramips: add support for Edimax Gemini RE23S Hardware -------- SoC: Mediatek MT7621AT (880 MHz, 2 cores 4 threads) RAM: 128MB FLASH: 16MB NOR (Macronix MX25L12805D) ETH: 1x 10/100/1000 Mbps Ethernet (MT7530) WIFI: - 2.4GHz: 1x MT7615 (4x4:4) - 5GHz: 1x MT7615 (4x4:4) - 4 antennas: 2 external detachable and 2 internal BTN: - 1x Reset button - 1x WPS button LEDS: - 1x Green led (Power) - 1x Green-Amber-Red led (Wifi) UART: - 57600-8-N-1 Everything works correctly. Installation ------------ Flash the factory image directly from OEM web interface. (You can login using these credentials: admin/1234) Restore OEM Firmware -------------------- Flash the OEM "bin" firmware directly from LUCI. The firmware is downloadable from the OEM web page. Warning: Remember to not keep settings! Warning2: Remember to force the flash. Restoring procedure tested with RE23_1.08.bin MAC addresses ------------- factory 0x4 *:24 factory 0x8004 *:25 Cimage 0x07 *:24 Cimage 0x0D *:24 Cimage 0x13 *:24 Cimage 0x19 *:25 No other addresses were found in factory partition. Since the label contains both the 2.4GHz and 5GHz mac address I decided to set the 5GHz one as label-mac-device. Moreover it also corresponds to the lan mac address. Notes ----- The wifi led in the OEM firmware changes colour depending on the signal strength. This can be done in OpenWrt but just for one interface. So for now will not be any default action for this led. If you want to open the case, pay attention to the antenna placed on the bottom part of the front cover. The wire is a bit short and it breaks easily. (I broke it) Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com> [fix two typos and add extended MAC address section to commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-19 23:27:56 +00:00
};
&switch0 {
ports {
port@4 {
status = "okay";
label = "lan";
};
};
};
&state_default {
gpio {
groups = "uart3", "uart2", "jtag", "wdt";
function = "gpio";
};
};
&xhci {
status = "disabled";
};