openwrt/target/linux/ramips/dts/mt7621_sercomm_s1500.dtsi

282 lines
5.3 KiB
Plaintext
Raw Normal View History

ramips: add support for Sercomm S1500 devices This commit adds support for following wireless routers: - Beeline SmartBox PRO (Serсomm S1500 AWI) - WiFire S1500.NBN (Serсomm S1500 BUC) This commit is based on this PR: - Link: https://github.com/openwrt/openwrt/pull/4770 - Author: Maximilian Weinmann <x1@disroot.org> The opening of this PR was agreed with author. My changes: - Sorting, minor changes and some movings between dts and dtsi - Move leds to dts when possible - Recipes for the factory image - Update of the installation/recovery/return to stock guides - Add reset GPIO for the pcie1 Common specification -------------------- SoC: MediaTek MT7621AT (880 MHz, 2 cores) Switch: MediaTek MT7530 (via SoC MT7621AT) Wireless: 2.4 GHz, MT7602EN, b/g/n, 2x2 Wireless: 5 GHz, MT7612EN, a/n/ac, 2x2 Ethernet: 5 ports - 5×GbE (WAN, LAN1-4) Mini PCIe: via J2 on PCB, not soldered on the board UART: J4 -> GND[], TX, VCC(3.3V), RX BootLoader: U-Boot SerComm/Mediatek Beeline SmartBox PRO specification ---------------------------------- RAM (Nanya NT5CB128M16FP): 256 MiB NAND-Flash (ESMT F59L2G81A): 256 MiB USB ports: 2xUSB2.0 LEDs: Status (white), WPS (blue), 2g (white), 5g (white) + 10 LED Ethernet Buttons: 2 button (reset, wps), 1 switch button (ROUT<->REP) Power: 12 VDC, 1.5 A PCB Sticker: 970AWI0QW00N256SMT Ver. 1.0 CSN: SG15******** MAC LAN: 94:4A:0C:**:**:** Manufacturer's code: 0AWI0500QW1 WiFire S1500.NBN specification ------------------------------ RAM (Nanya NT5CC64M16GP): 128 MiB NAND-Flash (ESMT F59L1G81MA): 128 MiB USB ports: 1xUSB2.0 LEDs: Status (white), WPS (white), 2g (white), 5g (white) + 10 LED Ethernet Buttons: 2 button (RESET, WPS) Power: 12 VDC, 1.0 A PCB Sticker: 970BUC0RW00N128SMT Ver. 1.0 CSN: MH16******** MAC WAN: E0:60:66:**:**:** Manufacturer's code: 0BUC0500RW1 MAC address table (PRO) ----------------------- use address source LAN *:23 factory 0x1000 (label) WAN *:24 factory $label +1 2g *:23 factory $label 5g *:25 factory $label +2 MAC addresses (NBN) ------------------- use address source LAN *:0e factory 0x1000 WAN *:0f LAN +1 (label) 2g *:0f LAN +1 5g *:10 LAN +2 OEM easy installation --------------------- 1. Remove all dots from the factory image filename (except the dot before file extension) 2. Upload and update the firmware via the original web interface 3. Two options are possible after the reboot: a. OpenWrt - that's OK, the mission accomplished b. Stock firmware - install Stock firmware (to switch booflag from Sercomm0 to Sercomm1) and then OpenWrt factory image. Return to Stock --------------- 1. Change the bootflag to Sercomm1 in OpenWrt CLI and then reboot: printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock2 reboot 2. Install stock firmware via the web OEM firmware interface Recovery -------- Use sercomm-recovery tool. Link: https://github.com/danitool/sercomm-recovery Tested-by: Pavel Ivanov <pi635v@gmail.com> Tested-by: Denis Myshaev <denis.myshaev@gmail.com> Tested-by: Oleg Galeev <olegingaleev@gmail.com> Tested-By: Ivan Pavlov <AuthorReflex@gmail.com> Co-authored-by: Maximilian Weinmann <x1@disroot.org> Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com> (cherry picked from commit 2d6784a033a994043759fa3b94c48afd5df81f88)
2023-06-11 20:50:23 +00:00
// SPDX-License-Identifier: GPL-2.0-or-later
#include "mt7621.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include <dt-bindings/leds/common.h>
/ {
aliases {
led-boot = &led_status;
led-running = &led_status;
led-upgrade = &led_wps;
led-failsafe = &led_wps;
};
keys {
compatible = "gpio-keys";
reset {
label = "reset";
gpios = <&gpio 7 GPIO_ACTIVE_LOW>;
linux,code = <KEY_RESTART>;
};
wps {
label = "wps";
gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
linux,code = <KEY_WPS_BUTTON>;
};
};
leds {
compatible = "gpio-leds";
led-0 {
label = "amber:lan4";
color = <LED_COLOR_ID_AMBER>;
function = LED_FUNCTION_LAN;
function-enumerator = <0>;
linux,default-trigger = "mt7530-0:00:1Gbps";
gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
};
led-1 {
label = "green:lan4";
color = <LED_COLOR_ID_GREEN>;
function = LED_FUNCTION_LAN;
function-enumerator = <1>;
gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
};
led-2 {
label = "amber:lan3";
color = <LED_COLOR_ID_AMBER>;
function = LED_FUNCTION_LAN;
function-enumerator = <2>;
linux,default-trigger = "mt7530-0:01:1Gbps";
gpios = <&gpio 10 GPIO_ACTIVE_LOW>;
};
led-3 {
label = "green:lan3";
color = <LED_COLOR_ID_GREEN>;
function = LED_FUNCTION_LAN;
function-enumerator = <3>;
gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
};
led-4 {
label = "amber:lan2";
color = <LED_COLOR_ID_AMBER>;
function = LED_FUNCTION_LAN;
function-enumerator = <4>;
linux,default-trigger = "mt7530-0:02:1Gbps";
gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
};
led-5 {
label = "amber:lan1";
color = <LED_COLOR_ID_AMBER>;
function = LED_FUNCTION_LAN;
function-enumerator = <5>;
linux,default-trigger = "mt7530-0:03:1Gbps";
gpios = <&gpio 22 GPIO_ACTIVE_LOW>;
};
led-6 {
label = "green:lan1";
color = <LED_COLOR_ID_GREEN>;
function = LED_FUNCTION_LAN;
function-enumerator = <6>;
gpios = <&gpio 23 GPIO_ACTIVE_LOW>;
};
led-7 {
label = "amber:wan";
color = <LED_COLOR_ID_AMBER>;
function = LED_FUNCTION_WAN;
function-enumerator = <0>;
linux,default-trigger = "mt7530-0:04:1Gbps";
gpios = <&gpio 24 GPIO_ACTIVE_LOW>;
};
led-8 {
label = "green:wan";
color = <LED_COLOR_ID_GREEN>;
function = LED_FUNCTION_WAN;
function-enumerator = <1>;
gpios = <&gpio 25 GPIO_ACTIVE_LOW>;
};
led-9 {
label = "green:lan2";
color = <LED_COLOR_ID_GREEN>;
function = LED_FUNCTION_LAN;
function-enumerator = <7>;
gpios = <&gpio 26 GPIO_ACTIVE_LOW>;
};
led-10 {
label = "white:wlan2g";
color = <LED_COLOR_ID_WHITE>;
function = LED_FUNCTION_WLAN;
function-enumerator = <0>;
linux,default-trigger = "phy1radio";
gpios = <&gpio 28 GPIO_ACTIVE_LOW>;
};
led_wps: led-11 {
function = LED_FUNCTION_WPS;
function-enumerator = <0>;
gpios = <&gpio 29 GPIO_ACTIVE_LOW>;
panic-indicator;
};
led_status: led-12 {
label = "white:status";
color = <LED_COLOR_ID_WHITE>;
function = LED_FUNCTION_STATUS;
function-enumerator = <0>;
gpios = <&gpio 30 GPIO_ACTIVE_LOW>;
};
led-13 {
label = "white:wlan5g";
color = <LED_COLOR_ID_WHITE>;
function = LED_FUNCTION_WLAN;
function-enumerator = <1>;
linux,default-trigger = "phy0radio";
gpios = <&gpio 32 GPIO_ACTIVE_LOW>;
};
};
};
&ethernet {
pinctrl-0 = <&mdio_pins>, <&rgmii1_pins>;
};
&gmac0 {
nvmem-cells = <&macaddr_factory_1000>;
nvmem-cell-names = "mac-address";
};
&nand {
status = "okay";
partitions: partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "u-boot";
reg = <0x0 0x100000>;
read-only;
};
factory: partition@100000 {
label = "Factory";
reg = <0x100000 0x100000>;
read-only;
compatible = "nvmem-cells";
#address-cells = <1>;
#size-cells = <1>;
macaddr_factory_1000: macaddr@1000 {
reg = <0x1000 0x6>;
};
};
partition@1600000 {
label = "boot_flag";
reg = <0x1600000 0x100000>;
};
partition@1700000 {
label = "kernel";
reg = <0x1700000 0x400000>;
};
partition@1b00000 {
label = "Kernel_2";
reg = <0x1b00000 0x400000>;
read-only;
};
};
};
&pcie {
status = "okay";
reset-gpios = <&gpio 8 GPIO_ACTIVE_LOW>,
<&gpio 19 GPIO_ACTIVE_LOW>;
};
&pcie0 {
wifi@0,0 {
compatible = "mediatek,mt76";
reg = <0x0000 0 0 0 0>;
ieee80211-freq-limit = <5000000 6000000>;
mediatek,mtd-eeprom = <&factory 0x8000>;
nvmem-cells = <&macaddr_factory_1000>;
nvmem-cell-names = "mac-address";
mac-address-increment = <2>;
};
};
&pcie1 {
wlan_2g: wifi@0,0 {
compatible = "mediatek,mt76";
reg = <0x0000 0 0 0 0>;
ieee80211-freq-limit = <2400000 2500000>;
mediatek,mtd-eeprom = <&factory 0x0>;
nvmem-cells = <&macaddr_factory_1000>;
nvmem-cell-names = "mac-address";
};
};
&state_default {
gpio {
groups = "wdt", "uart3", "jtag", "uart2", "i2c", "rgmii2";
function = "gpio";
};
};
&switch0 {
ports {
port@0 {
status = "okay";
label = "lan4";
};
port@1 {
status = "okay";
label = "lan3";
};
port@2 {
status = "okay";
label = "lan2";
};
port@3 {
status = "okay";
label = "lan1";
};
wan: port@4 {
status = "okay";
label = "wan";
nvmem-cells = <&macaddr_factory_1000>;
nvmem-cell-names = "mac-address";
mac-address-increment = <1>;
};
};
};