openwrt/target/linux/ath79/nand/base-files/etc/init.d/bootcount

#!/bin/sh /etc/rc.common
# SPDX-License-Identifier: GPL-2.0-only

START=99

boot() {
	case $(board_name) in
	glinet,gl-ar300m-nand)
		fw_setenv bootcount 0
		;;
	linksys,ea4500-v3)
		[ $(fw_printenv -n auto_recovery) = yes ] && \
			fw_setenv auto_recovery no
		;;
	esac
}
ath79: GL-AR300M: provide NAND support; increase to 4 MB kernel The GL.iNet GL-AR300M has been supported by the ar71xx and ath79 platforms with access to its 16 MB NOR flash, but not its 128 MB SPI NAND flash. This commit provides support for the NAND through the upstream SPI-NAND framework. Devices with both NOR and NAND flash can support independent firmware on each, with U-Boot able to boot from either. The OEM U-Boot will fall back to the NOR firmware after three "unsuccessful" boots. The family of GL-AR300M devices on the ath79 platform now includes: * glinet,gl-ar300m-lite "generic" target, NOR-only board * glinet,gl-ar300m-nand "nand" target * glinet,gl-ar300m-nor "nand" target (NAND-aware) NB: This commit increases the kernel size from 2 MB to 4 MB "Force-less" sysupgrade is presently supported from the current versions of following NOR-based firmwre images to the version of glinet,gl-ar300m-nor firmware produced by this commit: * gl-ar300m -- OEM v3 NOR ar71xx (openwrt-ar300m16-.bin) gl-ar300m -- OpenWrt 18.06 ar71xx * gl-ar300m -- OpenWrt 19.07 ar71xx Other upgrades to these images should be performed through U-Boot. The GL-AR300M OEM U-Boot allows upload and flashing of either NOR firmware (sysupgrade.bin) or NAND firmware (factory.img) through its HTTP-based GUI. Serial connectivity is not required. The glinet,gl-ar300m-nand and glinet,gl-ar300m-nor images generated after this commit should safely flash each other using sysupgrade. The boot counter is implemented by the OEM using u-boot-env. At this time, it does not appear that the switch on the side of the unit can be used to select NOR vs. NAND boot and the fail-over is only from NAND to NOR. To save flash wear, it is only reset when running the glinet,gl-ar300m-nand firmware. NAND-specific base-files are used to remove impact on existing generic and tiny targets. As there is now no "generic" build appropriate for the GL-AR300M16, (or for users of the GL-AR300M that do not need access to NAND) it will be introduced in a subsequent commit. Note: `mtd_get_mac_binary art 0x6` does not return the proper MAC and the GL.iNet source indicates that only the 0x0 offset is valid The ar71xx targets are unmodified. Signed-off-by: Jeff Kletsky <git-commits@allycomm.com> 2019-06-02 00:51:17 +00:00			`#!/bin/sh /etc/rc.common`
target: update SPDX license names SPDX moved from GPL-2.0 to GPL-2.0-only and from GPL-2.0+ to GPL-2.0-or-later. Reflect that in the SPDX license headers. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> 2020-09-22 18:49:55 +00:00			`# SPDX-License-Identifier: GPL-2.0-only`
ath79: GL-AR300M: provide NAND support; increase to 4 MB kernel The GL.iNet GL-AR300M has been supported by the ar71xx and ath79 platforms with access to its 16 MB NOR flash, but not its 128 MB SPI NAND flash. This commit provides support for the NAND through the upstream SPI-NAND framework. Devices with both NOR and NAND flash can support independent firmware on each, with U-Boot able to boot from either. The OEM U-Boot will fall back to the NOR firmware after three "unsuccessful" boots. The family of GL-AR300M devices on the ath79 platform now includes: * glinet,gl-ar300m-lite "generic" target, NOR-only board * glinet,gl-ar300m-nand "nand" target * glinet,gl-ar300m-nor "nand" target (NAND-aware) NB: This commit increases the kernel size from 2 MB to 4 MB "Force-less" sysupgrade is presently supported from the current versions of following NOR-based firmwre images to the version of glinet,gl-ar300m-nor firmware produced by this commit: * gl-ar300m -- OEM v3 NOR ar71xx (openwrt-ar300m16-.bin) gl-ar300m -- OpenWrt 18.06 ar71xx * gl-ar300m -- OpenWrt 19.07 ar71xx Other upgrades to these images should be performed through U-Boot. The GL-AR300M OEM U-Boot allows upload and flashing of either NOR firmware (sysupgrade.bin) or NAND firmware (factory.img) through its HTTP-based GUI. Serial connectivity is not required. The glinet,gl-ar300m-nand and glinet,gl-ar300m-nor images generated after this commit should safely flash each other using sysupgrade. The boot counter is implemented by the OEM using u-boot-env. At this time, it does not appear that the switch on the side of the unit can be used to select NOR vs. NAND boot and the fail-over is only from NAND to NOR. To save flash wear, it is only reset when running the glinet,gl-ar300m-nand firmware. NAND-specific base-files are used to remove impact on existing generic and tiny targets. As there is now no "generic" build appropriate for the GL-AR300M16, (or for users of the GL-AR300M that do not need access to NAND) it will be introduced in a subsequent commit. Note: `mtd_get_mac_binary art 0x6` does not return the proper MAC and the GL.iNet source indicates that only the 0x0 offset is valid The ar71xx targets are unmodified. Signed-off-by: Jeff Kletsky <git-commits@allycomm.com> 2019-06-02 00:51:17 +00:00
			`START=99`

			`boot() {`
			`case $(board_name) in`
			`glinet,gl-ar300m-nand)`
			`fw_setenv bootcount 0`
			`;;`
ath79: add support for Linksys EA4500 v3 Add support for the Linksys EA4500 v3 wireless router Hardware -------- SoC: Qualcomm Atheros QCA9558 RAM: 128M DDR2 (Winbond W971GG6KB-25) FLASH: 128M SPI-NAND (Spansion S34ML01G100TFI00) WLAN: QCA9558 3T3R 802.11 bgn QCA9580 3T3R 802.11 an ETH: Qualcomm Atheros QCA8337 UART: 115200 8n1, same as ea4500 v2 USB: 1 single USB 2.0 host port BUTTON: Reset - WPS LED: 1x system-LED LEDs besides the ethernet ports are controlled by the ethernet switch MAC Address: use address(sample 1) source label 94:10:3e:xx:xx:6f caldata@cal_macaddr lan 94:10:3e:xx:xx:6f $label wan 94:10:3e:xx:xx:6f $label WiFi4_2G 94:10:3e:xx:xx:70 caldata@cal_ath9k_soc WiFi4_5G 94:10:3e:xx:xx:71 caldata@cal_ath9k_pci Installation from Serial Console ------------ 1. Connect to the serial console. Power up the device and interrupt autoboot when prompted 2. Connect a TFTP server reachable at 192.168.1.0/24 (e.g. 192.168.1.66) to the ethernet port. Serve the OpenWrt initramfs image as "openwrt.bin" 3. To test OpenWrt only, go to step 4 and never execute step 5; To install, auto_recovery should be disabled first, and boot_part should be set to 1 if its current value is not. ath> setenv auto_recovery no ath> setenv boot_part 1 ath> saveenv 4. Boot the initramfs image using U-Boot ath> setenv serverip 192.168.1.66 ath> tftpboot 0x84000000 openwrt.bin ath> bootm 5. Copy the OpenWrt sysupgrade image to the device using scp and install it like a normal upgrade (with no need to keeping config since no config from "previous OpenWRT installation" could be kept at all) # sysupgrade -n /path/to/openwrt/sysupgrade.bin Note: Like many other routers produced by Linksys, it has a dual firmware flash layout, but because I do not know how to handle it, I decide to disable it for more usable space. (That is why the "auto_recovery" above should be disabled before installing OpenWRT.) If someone is interested in generating factory firmware image capable to flash from stock firmware, as well as restoring the dual firmware layout, commented-out layout for the original secondary partitions left in the device tree may be a useful hint. Installation from Web Interface ------------ 1. Login to the router via its web interface (default password: admin) 2. Find the firmware update interface under "Connectivity/Basic" 3. Choose the OpenWrt factory image and click "Start" 4. If the router still boots into the stock firmware, it means that the OpenWrt factory image has been installed to the secondary partitions and failed to boot (since OpenWrt on EA4500 v3 does not support dual boot yet), and the router switched back to the stock firmware on the primary partitions. You have to install a stock firmware (e.g. 3.1.6.172023, downloadable from https://www.linksys.com/support-article?articleNum=148385 ) first (to the secondary partitions) , and after that, install OpenWrt factory image (to the primary partitions). After successful installation of OpenWrt, auto_recovery will be automatically disabled and router will only boot from the primary partitions. Signed-off-by: Edward Chow <equu@openmail.cc> 2022-09-14 00:15:58 +00:00			`linksys,ea4500-v3)`
			`[ $(fw_printenv -n auto_recovery) = yes ] && \`
			`fw_setenv auto_recovery no`
			`;;`
ath79: GL-AR300M: provide NAND support; increase to 4 MB kernel The GL.iNet GL-AR300M has been supported by the ar71xx and ath79 platforms with access to its 16 MB NOR flash, but not its 128 MB SPI NAND flash. This commit provides support for the NAND through the upstream SPI-NAND framework. Devices with both NOR and NAND flash can support independent firmware on each, with U-Boot able to boot from either. The OEM U-Boot will fall back to the NOR firmware after three "unsuccessful" boots. The family of GL-AR300M devices on the ath79 platform now includes: * glinet,gl-ar300m-lite "generic" target, NOR-only board * glinet,gl-ar300m-nand "nand" target * glinet,gl-ar300m-nor "nand" target (NAND-aware) NB: This commit increases the kernel size from 2 MB to 4 MB "Force-less" sysupgrade is presently supported from the current versions of following NOR-based firmwre images to the version of glinet,gl-ar300m-nor firmware produced by this commit: * gl-ar300m -- OEM v3 NOR ar71xx (openwrt-ar300m16-.bin) gl-ar300m -- OpenWrt 18.06 ar71xx * gl-ar300m -- OpenWrt 19.07 ar71xx Other upgrades to these images should be performed through U-Boot. The GL-AR300M OEM U-Boot allows upload and flashing of either NOR firmware (sysupgrade.bin) or NAND firmware (factory.img) through its HTTP-based GUI. Serial connectivity is not required. The glinet,gl-ar300m-nand and glinet,gl-ar300m-nor images generated after this commit should safely flash each other using sysupgrade. The boot counter is implemented by the OEM using u-boot-env. At this time, it does not appear that the switch on the side of the unit can be used to select NOR vs. NAND boot and the fail-over is only from NAND to NOR. To save flash wear, it is only reset when running the glinet,gl-ar300m-nand firmware. NAND-specific base-files are used to remove impact on existing generic and tiny targets. As there is now no "generic" build appropriate for the GL-AR300M16, (or for users of the GL-AR300M that do not need access to NAND) it will be introduced in a subsequent commit. Note: `mtd_get_mac_binary art 0x6` does not return the proper MAC and the GL.iNet source indicates that only the 0x0 offset is valid The ar71xx targets are unmodified. Signed-off-by: Jeff Kletsky <git-commits@allycomm.com> 2019-06-02 00:51:17 +00:00			`esac`
			`}`