ExternalVendorCode/openwrt
1
0
Fork 0
mirror of https://github.com/openwrt/openwrt.git synced 2024-12-21 06:33:41 +00:00
Code Issues Actions 7 Packages Projects Releases Wiki Activity
30dcbc741d
openwrt/package/boot/uboot-envtools/files/ath79

38 lines
673 B
Plaintext
Raw Normal View History

uboot-envtools: add ath79 target This adds uci entries for all ath79 devices for which this already was the case on ar71xx. Additionally we add the OCEDO Koala as there was no support in OpenWRT yet. Signed-off-by: David Bauer <mail@david-bauer.net>
2018-08-06 14:21:01 +00:00
#!/bin/sh
#
# Copyright (C) 2011-2014 OpenWrt.org
#
[ -e /etc/config/ubootenv ] && exit 0
touch /etc/config/ubootenv
. /lib/uboot-envtools.sh
. /lib/functions.sh
board=$(board_name)
case "$board" in
uboot-envtools: ath79: add support for the Buffalo WZR-HP-AG300H Port support for the Buffalo WZR-HP-AG300H from the ar71xx target to ath79 as well. Build- and runtime tested on the Buffalo WZR-HP-AG300H. Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
2018-12-16 20:35:16 +00:00
buffalo,wzr-hp-ag300h)
ubootenv_add_uci_config "/dev/mtd3" "0x0" "0x10000" "0x10000"
;;
uboot-envtools: ath79: add support for the Buffalo BHR-4GRV2 According to https://github.com/openwrt/openwrt/pull/1527, support for the Buffalo BHR-4GRV2 in ath79 requires repartitioning from an initramfs image, make this easier by supporting uboot-envtools support out of the box. Build tested, but not runtime tested. Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
2018-12-16 20:41:55 +00:00
buffalo,bhr-4grv2|\
ath79: add support for EnGenius ECB1750 Specification: - Qualcomm Atheros SoC QCA9558 - 720/600/200 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 1x 10/100/1000 Mbps Ethernet - 3T3R 2.4 GHz (QCA9558 WMAC) - 3T3R 5.8 Ghz (QCA9880-BR4A, Senao PCE4553AH) https://fccid.io/A8J-ECB1750 Tested and working: - lan, wireless, leds, sysupgrade (tftp) Flash instructions: 1.) tftp recovery - use a 1GbE switch or direct attached 1GbE link - setup client ip address 192.168.1.10 and start tftpd - save "openwrt-ath79-generic-engenius_ecb1750-initramfs-kernel.bin" as "ap.bin" in tfpd root directory - plugin powercord and hold reset button 10secs.. "ap.bin" will be downloaded and executed - afterwards login via ssh and do a sysuprade 2.) oem webinterface factory install (not tested) Use normal webinterface upgrade page und select "openwrt-ath79-generic-engenius_ecb1750-squashfs-factory.bin". 3.) oem webinterface command injection OEM Firmware already running OpenWrt (Attitude Adjustment 12.09). Use OEM webinterface and command injection. See wiki for details. https://openwrt.org/toh/engenius/engenius_ecb1750_1 Signed-off-by: sven friedmann <sf.openwrt@okay.ms> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [use interrupt-driven "gpio-keys" binding]
2019-03-26 21:35:05 +00:00
engenius,ecb1750|\
ath79: fix boardname of GL.iNet GL-AR300M This device is called GL-AR300M, therefore rename the board(s) to 'gl-ar300m-nor' and 'gl-ar300m-nand' Signed-off-by: Paul Wassi <p.wassi@gmx.at> [change boardname in uboot envtools as well, don't use wildcards for boardname] Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-31 12:45:29 +00:00
glinet,gl-ar300m-nand|\
glinet,gl-ar300m-nor|\
ath79: add support for LibreRouter v1 Hardware -------- SOC: QCA9558 RAM: 128M DDR2 Flash: 16MiB SPI-NOR ETH: QCA8337N: 2x 10/100/1000 PoE and PoE pass-through WiFi2: QCA9558 (bgn) 2T2R WiFi5: 2x mPCIE with AR9582 (an) 2T2R BTN: 1x Reset GPIO: multiple GPIO on header, PoE passthrough enable UART: 3.3V 115200 8N1 header on the board WDG: ATTiny13 watchdog JTAG: header on the board USB: 1x connector and 1x header on the board PoE: 10-32V input in ETH port 1, passthrough in port 2 mPCIE: 2x populated with radios (but replaceable) OpenWrt is preinstalled from factory. To install use <your-image>-sysupgade.bin using the web interface or with sysupgrade -n. Flash from bootloader (in case failsafe does not work) 1. Connect the LibreRouter with a serial adapter (TTL voltage) to the UART header in the board. 2. Connect an ETH cable and configure static ip addres 192.168.1.10/24 3. Turn on the device and stop the bootloader sending any key through the serial interface. 4. Use a TFTP server to serve <your image>-sysupgrade.bin file. 5. Execute the following commands at the bootloader prompt: ath> tftp 82000000 <your image>-sysupgrade.bin ath> erase 0x9f050000 +$filesize ath> cp.b 0x82000000 0x9f050000 $filesize ath> bootm 0x9f050000 More docs * Bootloader https://github.com/librerouterorg/u-boot * Board details (schematics, gerbers): https://github.com/librerouterorg/board Signed-off-by: Santiago Piccinini <spiccinini@altermundi.net>
2019-03-09 01:10:25 +00:00
librerouter,librerouter-v1|\
ath79: add support for Netgear EX6400 and EX7300 This is sold as a dual-band 802.11ac range extender. It has a sliding switch for Extender mode or Access Point mode, a WPS button, a recessed Reset button, a hard-power button, and a multitude of LED's, some multiplexed via an NXP 74AHC164D chip. The internal serial header pinout is Vcc, Tx, Rx, GND, with GND closest to the corner of the board. You may connect at 115200 bps, 8 data bits, no parity, 1 stop bit. Specification: - System-On-Chip: QCA9558 - CPU/Speed: 720 MHz - Flash-Chip: Winbond 25Q128FVSG - Flash size: 16 MiB - RAM: 128 MiB - Wireless No1: QCA9558 on-chip 2.4GHz 802.11bgn, 3x3 - Wireless No2: QCA99x0 chip 5GHz 802.11an+ac, 4x4 - PHY: Atheros AR8035-A Installation: If you can get to the stock firmware's firmware upgrade option, just feed it the factory.img and boot as usual. As an alternative, TFTP the factory.img to the bootloader. Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us> [whitespace fix in DTS and reorder of make variables] Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-09-14 04:08:51 +00:00
netgear,ex6400|\
netgear,ex7300|\
ath79: add support for OCEDO Koala This commit adds support for the OCEDO Koala SOC: Qualcomm QCA9558 (Scorpion) RAM: 128MB FLASH: 16MiB WLAN1: QCA9558 2.4 GHz 802.11bgn 3x3 WLAN2: QCA9880 5 GHz 802.11nac 3x3 INPUT: RESET button LED: Power, LAN, WiFi 2.4, WiFi 5, SYS Serial: Header Next to Black metal shield Pinout is 3.3V - GND - TX - RX (Arrow Pad is 3.3V) The Serial setting is 115200-8-N-1. Tested and working: - Ethernet - 2.4 GHz WiFi - 5 GHz WiFi - TFTP boot from ramdisk image - Installation via ramdisk image - OpenWRT sysupgrade - Buttons - LEDs Installation seems to be possible only through booting an OpenWRT ramdisk image. Hold down the reset button while powering on the device. It will load a ramdisk image named 'koala-uImage-initramfs-lzma.bin' from 192.168.100.8. Note: depending on the present software, the device might also try to pull a file called 'koala-uimage-factory'. Only the name differs, it is still used as a ramdisk image. Wait for the ramdisk image to boot. OpenWRT can be written to the flash via sysupgrade or mtd. Due to the flip-flop bootloader which we not (yet) support, you need to set the partition the bootloader is selecting. It is possible from the initramfs image with > fw_setenv bootcmd run bootcmd_1 Afterwards you can reboot the device. Signed-off-by: David Bauer <mail@david-bauer.net>
2018-08-08 20:13:44 +00:00
ocedo,koala|\
uboot-envtools: add ath79 target This adds uci entries for all ath79 devices for which this already was the case on ar71xx. Additionally we add the OCEDO Koala as there was no support in OpenWRT yet. Signed-off-by: David Bauer <mail@david-bauer.net>
2018-08-06 14:21:01 +00:00
ocedo,raccoon|\
uboot-envtools: ath79: add support for YunCore A770 Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2019-03-09 15:31:22 +00:00
openmesh,om5p-ac-v2|\
yuncore,a770)
uboot-envtools: add ath79 target This adds uci entries for all ath79 devices for which this already was the case on ar71xx. Additionally we add the OCEDO Koala as there was no support in OpenWRT yet. Signed-off-by: David Bauer <mail@david-bauer.net>
2018-08-06 14:21:01 +00:00
ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x10000" "0x10000"
;;
esac
config_load ubootenv
config_foreach ubootenv_add_app_config ubootenv
exit 0
Reference in New Issue Copy Permalink