openwrt/target/linux/ramips/dts/mt7621_hanyang_hyc-g920.dts

210 lines
3.3 KiB
Plaintext
Raw Normal View History

ramips: Add support for CJ-Hello HYC-G920 Hanyang Digitech Co., Ltd. MSIP-CMM-HYD-HYC-G920 CJ-Hello HYC-G920 SoC : MediaTek MT7621AT RAM : 256M (SK hynix H5TQ2G63FFR) FLASH : 16MB (Winbond W25Q128BV) WiFi : MediaTek MT7602EN bgn 2SS WiFi : MediaTek MT7612EN nac 2SS BTN : Reset LED : - Power RED - WAN Green - LAN {1-4} - WiFi 2.4 GHz Blue - WiFi 5 GHz Blue - USB Green **For MT7621 stage1 DDR Test** UART : J4 GND - 3V3 - TX - RX - GND / 57600-8N1 ``` MT7621 stage1 code 10:33:55 (ASIC) CPU=500000000 HZ BUS=166666666 HZ ``` **For u boot environment** UART : J4 GND - 3V3 - TX - RX - GND / 115200-8N1 **UART Menu** ``` Please choose the operation: 1: Load system code to SDRAM via TFTP. 2: Load system code then write to Flash via TFTP. 3: Boot system code via Flash (default). 4: Entr boot command line interface. 7: Load Boot Loader code then write to Flash via Serial. 9: Load Boot Loader code then write to Flash via TFTP. ``` **Steps** Press 4: Entr boot command line interface. On the pormpt enter. `setenv firmware_size 0xf60000` Then enter. `saveenv` Then enter. `reset` **Device will reboot** Set your IP 192.168.100.100/24 Connect your lan cable to wan port. **On the UART Menu** Press 2: Load system code then write to Flash via TFTP. Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N) **enter** `Y` Please Input new ones /or Ctrl-C to discard Input device IP (192.168.100.55) ==:`192.168.100.55` Input server IP (192.168.100.100) ==:`192.168.100.100` Input Linux Kernel filename () ==:`openwrt-22.03.0-ramips-mt7621-hanyang_hyc-g920-squashfs-sysupgrade.bin` After uploading firmware image, device will boot Openwrt. Signed-off-by: Muhammad AL-Qadhy <m.ismael@gmail.com>
2023-03-21 06:49:22 +00:00
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
#include "mt7621.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
/ {
compatible = "hanyang,hyc-g920", "mediatek,mt7621-soc";
model = "CJ-Hello HYC-G920";
aliases {
led-boot = &led_power;
led-failsafe = &led_power;
led-running = &led_power;
led-upgrade = &led_power;
};
chosen {
bootargs = "console=ttyS0,115200";
bootargs-override = "console=ttyS0,115200";
};
leds {
compatible = "gpio-leds";
led_power: power {
label = "red:power";
gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
};
usb {
label = "green:usb";
gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
trigger-sources = <&ehci_port2>;
linux,default-trigger = "usbport";
};
};
keys {
compatible = "gpio-keys";
reset {
label = "reset";
gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
linux,code = <KEY_RESTART>;
debounce-interval = <60>;
};
};
};
&spi0 {
status = "okay";
flash@0 {
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <40000000>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "bootloader";
reg = <0x0 0x30000>;
read-only;
};
partition@30000 {
label = "mac";
reg = <0x30000 0x10000>;
read-only;
};
factory: partition@40000 {
label = "factory";
reg = <0x40000 0x10000>;
read-only;
nvmem-layout {
compatible = "fixed-layout";
#address-cells = <1>;
#size-cells = <1>;
eeprom_factory_0: eeprom@0 {
reg = <0x0 0x200>;
};
eeprom_factory_8000: eeprom@8000 {
reg = <0x8000 0x200>;
};
macaddr_factory_4: macaddr@4 {
compatible = "mac-base";
reg = <0x4 0x6>;
#nvmem-cell-cells = <1>;
};
macaddr_factory_8004: macaddr@8004 {
reg = <0x8004 0x6>;
};
};
ramips: Add support for CJ-Hello HYC-G920 Hanyang Digitech Co., Ltd. MSIP-CMM-HYD-HYC-G920 CJ-Hello HYC-G920 SoC : MediaTek MT7621AT RAM : 256M (SK hynix H5TQ2G63FFR) FLASH : 16MB (Winbond W25Q128BV) WiFi : MediaTek MT7602EN bgn 2SS WiFi : MediaTek MT7612EN nac 2SS BTN : Reset LED : - Power RED - WAN Green - LAN {1-4} - WiFi 2.4 GHz Blue - WiFi 5 GHz Blue - USB Green **For MT7621 stage1 DDR Test** UART : J4 GND - 3V3 - TX - RX - GND / 57600-8N1 ``` MT7621 stage1 code 10:33:55 (ASIC) CPU=500000000 HZ BUS=166666666 HZ ``` **For u boot environment** UART : J4 GND - 3V3 - TX - RX - GND / 115200-8N1 **UART Menu** ``` Please choose the operation: 1: Load system code to SDRAM via TFTP. 2: Load system code then write to Flash via TFTP. 3: Boot system code via Flash (default). 4: Entr boot command line interface. 7: Load Boot Loader code then write to Flash via Serial. 9: Load Boot Loader code then write to Flash via TFTP. ``` **Steps** Press 4: Entr boot command line interface. On the pormpt enter. `setenv firmware_size 0xf60000` Then enter. `saveenv` Then enter. `reset` **Device will reboot** Set your IP 192.168.100.100/24 Connect your lan cable to wan port. **On the UART Menu** Press 2: Load system code then write to Flash via TFTP. Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N) **enter** `Y` Please Input new ones /or Ctrl-C to discard Input device IP (192.168.100.55) ==:`192.168.100.55` Input server IP (192.168.100.100) ==:`192.168.100.100` Input Linux Kernel filename () ==:`openwrt-22.03.0-ramips-mt7621-hanyang_hyc-g920-squashfs-sysupgrade.bin` After uploading firmware image, device will boot Openwrt. Signed-off-by: Muhammad AL-Qadhy <m.ismael@gmail.com>
2023-03-21 06:49:22 +00:00
};
partition@50000 {
compatible = "denx,uimage";
label = "firmware";
reg = <0x50000 0xfb0000>;
};
partition@fb0000 {
label = "config ";
reg = <0xfb0000 0x20000>;
read-only;
};
partition@fd0000 {
label = "config_bak ";
reg = <0xfd0000 0x20000>;
read-only;
};
partition@ff0000 {
label = "mac_bak ";
reg = <0xff0000 0x10000>;
read-only;
};
};
};
};
&pcie {
status = "okay";
};
&pcie0 {
wifi@0,0 {
compatible = "mediatek,mt76";
reg = <0x0000 0 0 0 0>;
nvmem-cells = <&eeprom_factory_8000>;
nvmem-cell-names = "eeprom";
ieee80211-freq-limit = <5000000 6000000>;
ramips: Add support for CJ-Hello HYC-G920 Hanyang Digitech Co., Ltd. MSIP-CMM-HYD-HYC-G920 CJ-Hello HYC-G920 SoC : MediaTek MT7621AT RAM : 256M (SK hynix H5TQ2G63FFR) FLASH : 16MB (Winbond W25Q128BV) WiFi : MediaTek MT7602EN bgn 2SS WiFi : MediaTek MT7612EN nac 2SS BTN : Reset LED : - Power RED - WAN Green - LAN {1-4} - WiFi 2.4 GHz Blue - WiFi 5 GHz Blue - USB Green **For MT7621 stage1 DDR Test** UART : J4 GND - 3V3 - TX - RX - GND / 57600-8N1 ``` MT7621 stage1 code 10:33:55 (ASIC) CPU=500000000 HZ BUS=166666666 HZ ``` **For u boot environment** UART : J4 GND - 3V3 - TX - RX - GND / 115200-8N1 **UART Menu** ``` Please choose the operation: 1: Load system code to SDRAM via TFTP. 2: Load system code then write to Flash via TFTP. 3: Boot system code via Flash (default). 4: Entr boot command line interface. 7: Load Boot Loader code then write to Flash via Serial. 9: Load Boot Loader code then write to Flash via TFTP. ``` **Steps** Press 4: Entr boot command line interface. On the pormpt enter. `setenv firmware_size 0xf60000` Then enter. `saveenv` Then enter. `reset` **Device will reboot** Set your IP 192.168.100.100/24 Connect your lan cable to wan port. **On the UART Menu** Press 2: Load system code then write to Flash via TFTP. Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N) **enter** `Y` Please Input new ones /or Ctrl-C to discard Input device IP (192.168.100.55) ==:`192.168.100.55` Input server IP (192.168.100.100) ==:`192.168.100.100` Input Linux Kernel filename () ==:`openwrt-22.03.0-ramips-mt7621-hanyang_hyc-g920-squashfs-sysupgrade.bin` After uploading firmware image, device will boot Openwrt. Signed-off-by: Muhammad AL-Qadhy <m.ismael@gmail.com>
2023-03-21 06:49:22 +00:00
led {
led-sources = <2>;
led-active-low;
};
};
};
&pcie1 {
wifi@0,0 {
compatible = "mediatek,mt76";
reg = <0x0000 0 0 0 0>;
nvmem-cells = <&eeprom_factory_0>;
nvmem-cell-names = "eeprom";
ieee80211-freq-limit = <2400000 2500000>;
ramips: Add support for CJ-Hello HYC-G920 Hanyang Digitech Co., Ltd. MSIP-CMM-HYD-HYC-G920 CJ-Hello HYC-G920 SoC : MediaTek MT7621AT RAM : 256M (SK hynix H5TQ2G63FFR) FLASH : 16MB (Winbond W25Q128BV) WiFi : MediaTek MT7602EN bgn 2SS WiFi : MediaTek MT7612EN nac 2SS BTN : Reset LED : - Power RED - WAN Green - LAN {1-4} - WiFi 2.4 GHz Blue - WiFi 5 GHz Blue - USB Green **For MT7621 stage1 DDR Test** UART : J4 GND - 3V3 - TX - RX - GND / 57600-8N1 ``` MT7621 stage1 code 10:33:55 (ASIC) CPU=500000000 HZ BUS=166666666 HZ ``` **For u boot environment** UART : J4 GND - 3V3 - TX - RX - GND / 115200-8N1 **UART Menu** ``` Please choose the operation: 1: Load system code to SDRAM via TFTP. 2: Load system code then write to Flash via TFTP. 3: Boot system code via Flash (default). 4: Entr boot command line interface. 7: Load Boot Loader code then write to Flash via Serial. 9: Load Boot Loader code then write to Flash via TFTP. ``` **Steps** Press 4: Entr boot command line interface. On the pormpt enter. `setenv firmware_size 0xf60000` Then enter. `saveenv` Then enter. `reset` **Device will reboot** Set your IP 192.168.100.100/24 Connect your lan cable to wan port. **On the UART Menu** Press 2: Load system code then write to Flash via TFTP. Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N) **enter** `Y` Please Input new ones /or Ctrl-C to discard Input device IP (192.168.100.55) ==:`192.168.100.55` Input server IP (192.168.100.100) ==:`192.168.100.100` Input Linux Kernel filename () ==:`openwrt-22.03.0-ramips-mt7621-hanyang_hyc-g920-squashfs-sysupgrade.bin` After uploading firmware image, device will boot Openwrt. Signed-off-by: Muhammad AL-Qadhy <m.ismael@gmail.com>
2023-03-21 06:49:22 +00:00
led {
led-sources = <2>;
led-active-low;
};
};
};
&gmac0 {
nvmem-cells = <&macaddr_factory_4 0>;
ramips: Add support for CJ-Hello HYC-G920 Hanyang Digitech Co., Ltd. MSIP-CMM-HYD-HYC-G920 CJ-Hello HYC-G920 SoC : MediaTek MT7621AT RAM : 256M (SK hynix H5TQ2G63FFR) FLASH : 16MB (Winbond W25Q128BV) WiFi : MediaTek MT7602EN bgn 2SS WiFi : MediaTek MT7612EN nac 2SS BTN : Reset LED : - Power RED - WAN Green - LAN {1-4} - WiFi 2.4 GHz Blue - WiFi 5 GHz Blue - USB Green **For MT7621 stage1 DDR Test** UART : J4 GND - 3V3 - TX - RX - GND / 57600-8N1 ``` MT7621 stage1 code 10:33:55 (ASIC) CPU=500000000 HZ BUS=166666666 HZ ``` **For u boot environment** UART : J4 GND - 3V3 - TX - RX - GND / 115200-8N1 **UART Menu** ``` Please choose the operation: 1: Load system code to SDRAM via TFTP. 2: Load system code then write to Flash via TFTP. 3: Boot system code via Flash (default). 4: Entr boot command line interface. 7: Load Boot Loader code then write to Flash via Serial. 9: Load Boot Loader code then write to Flash via TFTP. ``` **Steps** Press 4: Entr boot command line interface. On the pormpt enter. `setenv firmware_size 0xf60000` Then enter. `saveenv` Then enter. `reset` **Device will reboot** Set your IP 192.168.100.100/24 Connect your lan cable to wan port. **On the UART Menu** Press 2: Load system code then write to Flash via TFTP. Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N) **enter** `Y` Please Input new ones /or Ctrl-C to discard Input device IP (192.168.100.55) ==:`192.168.100.55` Input server IP (192.168.100.100) ==:`192.168.100.100` Input Linux Kernel filename () ==:`openwrt-22.03.0-ramips-mt7621-hanyang_hyc-g920-squashfs-sysupgrade.bin` After uploading firmware image, device will boot Openwrt. Signed-off-by: Muhammad AL-Qadhy <m.ismael@gmail.com>
2023-03-21 06:49:22 +00:00
nvmem-cell-names = "mac-address";
};
&switch0 {
ports {
port@0 {
status = "okay";
label = "wan";
nvmem-cells = <&macaddr_factory_4 1>;
ramips: Add support for CJ-Hello HYC-G920 Hanyang Digitech Co., Ltd. MSIP-CMM-HYD-HYC-G920 CJ-Hello HYC-G920 SoC : MediaTek MT7621AT RAM : 256M (SK hynix H5TQ2G63FFR) FLASH : 16MB (Winbond W25Q128BV) WiFi : MediaTek MT7602EN bgn 2SS WiFi : MediaTek MT7612EN nac 2SS BTN : Reset LED : - Power RED - WAN Green - LAN {1-4} - WiFi 2.4 GHz Blue - WiFi 5 GHz Blue - USB Green **For MT7621 stage1 DDR Test** UART : J4 GND - 3V3 - TX - RX - GND / 57600-8N1 ``` MT7621 stage1 code 10:33:55 (ASIC) CPU=500000000 HZ BUS=166666666 HZ ``` **For u boot environment** UART : J4 GND - 3V3 - TX - RX - GND / 115200-8N1 **UART Menu** ``` Please choose the operation: 1: Load system code to SDRAM via TFTP. 2: Load system code then write to Flash via TFTP. 3: Boot system code via Flash (default). 4: Entr boot command line interface. 7: Load Boot Loader code then write to Flash via Serial. 9: Load Boot Loader code then write to Flash via TFTP. ``` **Steps** Press 4: Entr boot command line interface. On the pormpt enter. `setenv firmware_size 0xf60000` Then enter. `saveenv` Then enter. `reset` **Device will reboot** Set your IP 192.168.100.100/24 Connect your lan cable to wan port. **On the UART Menu** Press 2: Load system code then write to Flash via TFTP. Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N) **enter** `Y` Please Input new ones /or Ctrl-C to discard Input device IP (192.168.100.55) ==:`192.168.100.55` Input server IP (192.168.100.100) ==:`192.168.100.100` Input Linux Kernel filename () ==:`openwrt-22.03.0-ramips-mt7621-hanyang_hyc-g920-squashfs-sysupgrade.bin` After uploading firmware image, device will boot Openwrt. Signed-off-by: Muhammad AL-Qadhy <m.ismael@gmail.com>
2023-03-21 06:49:22 +00:00
nvmem-cell-names = "mac-address";
};
port@1 {
status = "okay";
label = "lan1";
};
port@2 {
status = "okay";
label = "lan2";
};
port@3 {
status = "okay";
label = "lan3";
};
port@4 {
status = "okay";
label = "lan4";
};
};
};
&state_default {
gpio {
groups = "sdhci";
function = "gpio";
};
};