ExternalVendorCode/openwrt
1
0
Fork 0
mirror of https://github.com/openwrt/openwrt.git synced 2024-12-25 00:11:13 +00:00
Code Issues Actions 3 Packages Projects Releases Wiki Activity
24fddfa1be
openwrt/target/linux/ath79/image/generic-ubnt.mk

246 lines
6.7 KiB
Makefile
Raw Normal View History

ath79: ubnt-m-xw: Fix factory image flashing using TFTP recovery method Ubiquity allows flashing of unsigned factory images via TFTP recovery method[1]. They claim in airOS v6.0.7 release changelog[2] following: All future airOS versions will be signed in this way and not allow unsigned firmware to be loaded except via TFTP. U-boot bootloader on M-XW devices expects factory image revision version in specific format. On airOS v6.1.7 with `U-Boot 1.1.4-s1039 (May 24 2017 - 15:58:18)` bootloader checks if the revision major(?) number is actually a number, but in currently generated images there's OpenWrt text and so the check fails: Hit any key to stop autoboot: 0 Setting default IP 192.168.1.20 Starting TFTP server... Receiving file from 192.168.1.25:38438 Received 4981148 bytes Firmware check failed! (1) By placing arbitrary correct number first in major version, we make the bootloader happy and we can flash factory images over TFTP again: Received 3735964 bytes Firmware Version: XW.ar934x.v6.0.4-42.r8474-56aa1ac-OpenWrt Setting U-Boot environment variables Un-Protected 1 sectors Erasing Flash.... done Patch provided by AREDN[3] project, tested on Bullet M2 XW (ynezz) and Nanostation M5 XW (ae6xe). 1. https://help.ubnt.com/hc/en-us/articles/204910124-UniFi-TFTP-Recovery-for-Bricked-Access-Points 2. https://dl.ubnt.com/firmwares/XW-fw/v6.0.7/changelog.txt 3. https://github.com/aredn Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-11-19 20:44:50 +00:00
DEVICE_VARS += UBNT_BOARD UBNT_CHIP UBNT_TYPE UBNT_VERSION UBNT_REVISION
# On M (XW) devices the U-Boot as of version 1.1.4-s1039 doesn't like
# VERSION_DIST being on the place of major(?) version number, so we need to
# use some number.
UBNT_REVISION := $(VERSION_DIST)-$(REVISION)
ath79: add new OF only target for QCA MIPS silicon This target aims to replace ar71xx mid-term. The big part that is still missing is making the MMIO/AHB wifi work using OF. NAND and mikrotik subtargets will follow. Signed-off-by: John Crispin <john@phrozen.org>
2018-05-06 08:20:11 +00:00
# mkubntimage is using the kernel image direct
# routerboard creates partitions out of the ubnt header
define Build/mkubntimage
-$(STAGING_DIR_HOST)/bin/mkfwimage \
-B $(UBNT_BOARD) -v $(UBNT_TYPE).$(UBNT_CHIP).v6.0.0-$(VERSION_DIST)-$(REVISION) \
-k $(IMAGE_KERNEL) \
-r $@ \
-o $@
endef
ath79: Add support for Ubiquiti NanoStation AC loco Atheros AR9342, 16 MB flash, 64 MB RAM Successor to the old NanoStation M5 loco with AC wireless. Includes a mac80211 patch for ath10k_pci because Ubiquiti uses a Ubiquiti branded and customized QCA988X with vendor id 0777 and device id 11ac for AC wireless. Installation 1. Connect to serial header on device (8N1 115200) 2. Power on device and enter uboot console 3. Set up tftp server serving an openwrt initramfs build 4. Load initramfs build using the command tftpboot in the uboot cli 5. Boot the loaded image using the command bootm 6. Copy squashfs openwrt sysupgrade build to the booted device 7. Use mtd to write sysupgrade to partition "firmware" 8. Reboot and enjoy Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
2018-01-23 10:36:41 +00:00
# all UBNT XM/WA devices expect the kernel image to have 1024k while flash, when
ath79: add new OF only target for QCA MIPS silicon This target aims to replace ar71xx mid-term. The big part that is still missing is making the MMIO/AHB wifi work using OF. NAND and mikrotik subtargets will follow. Signed-off-by: John Crispin <john@phrozen.org>
2018-05-06 08:20:11 +00:00
# booting the image, the size doesn't matter.
define Build/mkubntimage-split
-[ -f $@ ] && ( \
dd if=$@ of=$@.old1 bs=1024k count=1; \
dd if=$@ of=$@.old2 bs=1024k skip=1; \
$(STAGING_DIR_HOST)/bin/mkfwimage \
ath79: ubnt-m-xw: Fix factory image flashing using TFTP recovery method Ubiquity allows flashing of unsigned factory images via TFTP recovery method[1]. They claim in airOS v6.0.7 release changelog[2] following: All future airOS versions will be signed in this way and not allow unsigned firmware to be loaded except via TFTP. U-boot bootloader on M-XW devices expects factory image revision version in specific format. On airOS v6.1.7 with `U-Boot 1.1.4-s1039 (May 24 2017 - 15:58:18)` bootloader checks if the revision major(?) number is actually a number, but in currently generated images there's OpenWrt text and so the check fails: Hit any key to stop autoboot: 0 Setting default IP 192.168.1.20 Starting TFTP server... Receiving file from 192.168.1.25:38438 Received 4981148 bytes Firmware check failed! (1) By placing arbitrary correct number first in major version, we make the bootloader happy and we can flash factory images over TFTP again: Received 3735964 bytes Firmware Version: XW.ar934x.v6.0.4-42.r8474-56aa1ac-OpenWrt Setting U-Boot environment variables Un-Protected 1 sectors Erasing Flash.... done Patch provided by AREDN[3] project, tested on Bullet M2 XW (ynezz) and Nanostation M5 XW (ae6xe). 1. https://help.ubnt.com/hc/en-us/articles/204910124-UniFi-TFTP-Recovery-for-Bricked-Access-Points 2. https://dl.ubnt.com/firmwares/XW-fw/v6.0.7/changelog.txt 3. https://github.com/aredn Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-11-19 20:44:50 +00:00
-B $(UBNT_BOARD) -v $(UBNT_TYPE).$(UBNT_CHIP).v$(UBNT_VERSION)-$(UBNT_REVISION) \
ath79: add new OF only target for QCA MIPS silicon This target aims to replace ar71xx mid-term. The big part that is still missing is making the MMIO/AHB wifi work using OF. NAND and mikrotik subtargets will follow. Signed-off-by: John Crispin <john@phrozen.org>
2018-05-06 08:20:11 +00:00
-k $@.old1 \
-r $@.old2 \
-o $@; \
rm $@.old1 $@.old2 )
endef
# UBNT_BOARD e.g. one of (XS2, XS5, RS, XM)
# UBNT_TYPE e.g. one of (BZ, XM, XW)
# UBNT_CHIP e.g. one of (ar7240, ar933x, ar934x)
ath79: Add support for Ubiquiti NanoStation AC loco Atheros AR9342, 16 MB flash, 64 MB RAM Successor to the old NanoStation M5 loco with AC wireless. Includes a mac80211 patch for ath10k_pci because Ubiquiti uses a Ubiquiti branded and customized QCA988X with vendor id 0777 and device id 11ac for AC wireless. Installation 1. Connect to serial header on device (8N1 115200) 2. Power on device and enter uboot console 3. Set up tftp server serving an openwrt initramfs build 4. Load initramfs build using the command tftpboot in the uboot cli 5. Boot the loaded image using the command bootm 6. Copy squashfs openwrt sysupgrade build to the booted device 7. Use mtd to write sysupgrade to partition "firmware" 8. Reboot and enjoy Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
2018-01-23 10:36:41 +00:00
# UBNT_VERSION e.g. one of (6.0.0, 8.5.0)
ath79: add new OF only target for QCA MIPS silicon This target aims to replace ar71xx mid-term. The big part that is still missing is making the MMIO/AHB wifi work using OF. NAND and mikrotik subtargets will follow. Signed-off-by: John Crispin <john@phrozen.org>
2018-05-06 08:20:11 +00:00
define Device/ubnt
DEVICE_PACKAGES := kmod-usb-core kmod-usb2
IMAGE_SIZE := 7552k
UBNT_BOARD := XM
ath79: Add support for Ubiquiti NanoStation AC loco Atheros AR9342, 16 MB flash, 64 MB RAM Successor to the old NanoStation M5 loco with AC wireless. Includes a mac80211 patch for ath10k_pci because Ubiquiti uses a Ubiquiti branded and customized QCA988X with vendor id 0777 and device id 11ac for AC wireless. Installation 1. Connect to serial header on device (8N1 115200) 2. Power on device and enter uboot console 3. Set up tftp server serving an openwrt initramfs build 4. Load initramfs build using the command tftpboot in the uboot cli 5. Boot the loaded image using the command bootm 6. Copy squashfs openwrt sysupgrade build to the booted device 7. Use mtd to write sysupgrade to partition "firmware" 8. Reboot and enjoy Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
2018-01-23 10:36:41 +00:00
UBNT_VERSION := 6.0.0
ath79: add and enforce image metadata Add metadata to images and make the metdata mandatory. Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-05-07 20:41:04 +00:00
IMAGES += factory.bin
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
append-rootfs | pad-rootfs | check-size $$$$(IMAGE_SIZE) | mkubntimage-split
ath79: add new OF only target for QCA MIPS silicon This target aims to replace ar71xx mid-term. The big part that is still missing is making the MMIO/AHB wifi work using OF. NAND and mikrotik subtargets will follow. Signed-off-by: John Crispin <john@phrozen.org>
2018-05-06 08:20:11 +00:00
endef
define Device/ubnt-xm
$(Device/ubnt)
ath79: ubnt-xm: add rssileds package In order to make RSSI indicator on the device work out of box, include "rssileds" package in per-device rootfs image by default for Ubiquiti XM family. Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
2018-09-05 17:40:16 +00:00
DEVICE_PACKAGES += kmod-usb-ohci rssileds
ath79: add new OF only target for QCA MIPS silicon This target aims to replace ar71xx mid-term. The big part that is still missing is making the MMIO/AHB wifi work using OF. NAND and mikrotik subtargets will follow. Signed-off-by: John Crispin <john@phrozen.org>
2018-05-06 08:20:11 +00:00
UBNT_TYPE := XM
UBNT_CHIP := ar7240
ATH_SOC := ar7241
ath79: Ubiquiti Airmax M: add relocate-kernel to invalidate cache Apply ar71xx fix for broken Ubiquiti bootloader to ath79 as well. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2018-04-26 18:04:48 +00:00
KERNEL := kernel-bin | append-dtb | relocate-kernel | lzma | uImage lzma
ath79: add new OF only target for QCA MIPS silicon This target aims to replace ar71xx mid-term. The big part that is still missing is making the MMIO/AHB wifi work using OF. NAND and mikrotik subtargets will follow. Signed-off-by: John Crispin <john@phrozen.org>
2018-05-06 08:20:11 +00:00
endef
define Device/ubnt-bz
$(Device/ubnt)
UBNT_TYPE := BZ
UBNT_CHIP := ar7240
ath79: cleanup image build code Remove recipes for not yet migrated boards. Drop variables which aren't required due to the switch to devicetree like boardname. Drop the legacy image build code. Boards added to this target shouldn't use the legacy image build code anyway. Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-05-07 19:09:44 +00:00
ATH_SOC := ar7241
ath79: add new OF only target for QCA MIPS silicon This target aims to replace ar71xx mid-term. The big part that is still missing is making the MMIO/AHB wifi work using OF. NAND and mikrotik subtargets will follow. Signed-off-by: John Crispin <john@phrozen.org>
2018-05-06 08:20:11 +00:00
endef
ath79: Add support for Ubiquiti NanoStation AC loco Atheros AR9342, 16 MB flash, 64 MB RAM Successor to the old NanoStation M5 loco with AC wireless. Includes a mac80211 patch for ath10k_pci because Ubiquiti uses a Ubiquiti branded and customized QCA988X with vendor id 0777 and device id 11ac for AC wireless. Installation 1. Connect to serial header on device (8N1 115200) 2. Power on device and enter uboot console 3. Set up tftp server serving an openwrt initramfs build 4. Load initramfs build using the command tftpboot in the uboot cli 5. Boot the loaded image using the command bootm 6. Copy squashfs openwrt sysupgrade build to the booted device 7. Use mtd to write sysupgrade to partition "firmware" 8. Reboot and enjoy Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
2018-01-23 10:36:41 +00:00
define Device/ubnt-wa
$(Device/ubnt)
UBNT_TYPE := WA
UBNT_CHIP := ar934x
UBNT_BOARD := WA
UBNT_VERSION := 8.5.0
ATH_SOC := ar9342
endef
ath79: Add support for Ubiquity Bullet M (XW) CPU: AR9342 SoC RAM: 64 MB DDR2 Flash: 8 MB NOR SPI Ports: 100 MBit (24V PoE in) WLAN: 2.4/5 GHz UART: 1 UART on PCB marked as J1 with 115200 8N1 config LEDs: Power, Ethernet, 4x RSSI LEDs (orange, red, 2x green) Buttons: Reset UART connection details .---------------------------------. | | [ETH] J1 [ANT] | o VCC o RX o TX o GND | `---------------------------------' Flashing instructions A) Serial console, U-Boot and TFTP 1. Connect to serial header J1 on the PCB 2. Power on device and enter U-Boot console 3. Set up TFTP server serving an OpenWrt initramfs build 4. Load initramfs build using the command tftpboot in the U-Boot cli 5. Boot the loaded image using the command bootm 6. Copy squashfs OpenWrt sysupgrade build to the booted device 7. Use mtd to write sysupgrade to partition "firmware" 8. Reboot and enjoy B) Experimental factory image flashing over SSH from airOS v6.1.7 1. You need to flash your UBNT M2HP with airOS v6.1.7 firmware no other airOS version is currently supported 2. git clone https://github.com/true-systems/ubnt-bullet-m2hp-openwrt-flashing 3. cd ubnt-bullet-m2hp-openwrt-flashing 4. make flash-factory FW_OWRT=/path/to/your/openwrt-ath79-generic-ubnt_bullet-m-xw-squashfs-factory.bin Tested only on Bullet M2HP. Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-11-17 07:01:55 +00:00
define Device/ubnt-xw
$(Device/ubnt)
UBNT_TYPE := XW
UBNT_CHIP := ar934x
UBNT_BOARD := XM
UBNT_VERSION := 6.0.4
ath79: ubnt-m-xw: Fix factory image flashing using TFTP recovery method Ubiquity allows flashing of unsigned factory images via TFTP recovery method[1]. They claim in airOS v6.0.7 release changelog[2] following: All future airOS versions will be signed in this way and not allow unsigned firmware to be loaded except via TFTP. U-boot bootloader on M-XW devices expects factory image revision version in specific format. On airOS v6.1.7 with `U-Boot 1.1.4-s1039 (May 24 2017 - 15:58:18)` bootloader checks if the revision major(?) number is actually a number, but in currently generated images there's OpenWrt text and so the check fails: Hit any key to stop autoboot: 0 Setting default IP 192.168.1.20 Starting TFTP server... Receiving file from 192.168.1.25:38438 Received 4981148 bytes Firmware check failed! (1) By placing arbitrary correct number first in major version, we make the bootloader happy and we can flash factory images over TFTP again: Received 3735964 bytes Firmware Version: XW.ar934x.v6.0.4-42.r8474-56aa1ac-OpenWrt Setting U-Boot environment variables Un-Protected 1 sectors Erasing Flash.... done Patch provided by AREDN[3] project, tested on Bullet M2 XW (ynezz) and Nanostation M5 XW (ae6xe). 1. https://help.ubnt.com/hc/en-us/articles/204910124-UniFi-TFTP-Recovery-for-Bricked-Access-Points 2. https://dl.ubnt.com/firmwares/XW-fw/v6.0.7/changelog.txt 3. https://github.com/aredn Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-11-19 20:44:50 +00:00
UBNT_REVISION := 42.$(UBNT_REVISION)
ath79: Add support for Ubiquity Bullet M (XW) CPU: AR9342 SoC RAM: 64 MB DDR2 Flash: 8 MB NOR SPI Ports: 100 MBit (24V PoE in) WLAN: 2.4/5 GHz UART: 1 UART on PCB marked as J1 with 115200 8N1 config LEDs: Power, Ethernet, 4x RSSI LEDs (orange, red, 2x green) Buttons: Reset UART connection details .---------------------------------. | | [ETH] J1 [ANT] | o VCC o RX o TX o GND | `---------------------------------' Flashing instructions A) Serial console, U-Boot and TFTP 1. Connect to serial header J1 on the PCB 2. Power on device and enter U-Boot console 3. Set up TFTP server serving an OpenWrt initramfs build 4. Load initramfs build using the command tftpboot in the U-Boot cli 5. Boot the loaded image using the command bootm 6. Copy squashfs OpenWrt sysupgrade build to the booted device 7. Use mtd to write sysupgrade to partition "firmware" 8. Reboot and enjoy B) Experimental factory image flashing over SSH from airOS v6.1.7 1. You need to flash your UBNT M2HP with airOS v6.1.7 firmware no other airOS version is currently supported 2. git clone https://github.com/true-systems/ubnt-bullet-m2hp-openwrt-flashing 3. cd ubnt-bullet-m2hp-openwrt-flashing 4. make flash-factory FW_OWRT=/path/to/your/openwrt-ath79-generic-ubnt_bullet-m-xw-squashfs-factory.bin Tested only on Bullet M2HP. Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-11-17 07:01:55 +00:00
ATH_SOC := ar9342
endef
ath79: add support for Ubiquiti AirRouter Indoor low-power router with 2.4 GHz radio CPU: Atheros AR7241 rev 1 RAM: 32 MB Flash: 8 MB NOR SPI Switch: Atheros AR7240 Ports: 1x WAN, 4x LAN 10/100 Ethernet WLAN: Atheros AR9285 (2.4 GHz) USB: 1x USB2 host port Note: Ethernet WAN/LAN port naming is reversed from ar71xx. WAN is eth0; LAN is eth1.1. UART settings: 115200, 8N1 LEDs +-------------------------- | | | | | | | | VCC | x x RX | * x | x x | x x TX | * x GND | * x | | | | +-------------------------- ETHERNET PORTS Installation from Ubiquiti firmware, is as for other ubnt-xm AirOs devices. Signed-off-by: Russell Senior <russell@personaltelco.net>
2018-11-26 22:28:00 +00:00
define Device/ubnt_airrouter
$(Device/ubnt-xm)
DEVICE_TITLE := Ubiquiti AirRouter
SUPPORTED_DEVICES += airrouter
endef
TARGET_DEVICES += ubnt_airrouter
ath79: fix dts files Add the SoC compatible to the individual dts files. Rename the dts files to match the common pattern. Remove dts files wich aren't used and no image in ar71xx exists. Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-05-08 05:22:38 +00:00
define Device/ubnt_bullet-m
ath79: add new OF only target for QCA MIPS silicon This target aims to replace ar71xx mid-term. The big part that is still missing is making the MMIO/AHB wifi work using OF. NAND and mikrotik subtargets will follow. Signed-off-by: John Crispin <john@phrozen.org>
2018-05-06 08:20:11 +00:00
$(Device/ubnt-xm)
DEVICE_TITLE := Ubiquiti Bullet-M
ath79: add and enforce image metadata Add metadata to images and make the metdata mandatory. Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-05-07 20:41:04 +00:00
SUPPORTED_DEVICES += bullet-m
ath79: add new OF only target for QCA MIPS silicon This target aims to replace ar71xx mid-term. The big part that is still missing is making the MMIO/AHB wifi work using OF. NAND and mikrotik subtargets will follow. Signed-off-by: John Crispin <john@phrozen.org>
2018-05-06 08:20:11 +00:00
endef
ath79: fix dts files Add the SoC compatible to the individual dts files. Rename the dts files to match the common pattern. Remove dts files wich aren't used and no image in ar71xx exists. Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-05-08 05:22:38 +00:00
TARGET_DEVICES += ubnt_bullet-m
ath79: add new OF only target for QCA MIPS silicon This target aims to replace ar71xx mid-term. The big part that is still missing is making the MMIO/AHB wifi work using OF. NAND and mikrotik subtargets will follow. Signed-off-by: John Crispin <john@phrozen.org>
2018-05-06 08:20:11 +00:00
ath79: Add support for Ubiquity Bullet M (XW) CPU: AR9342 SoC RAM: 64 MB DDR2 Flash: 8 MB NOR SPI Ports: 100 MBit (24V PoE in) WLAN: 2.4/5 GHz UART: 1 UART on PCB marked as J1 with 115200 8N1 config LEDs: Power, Ethernet, 4x RSSI LEDs (orange, red, 2x green) Buttons: Reset UART connection details .---------------------------------. | | [ETH] J1 [ANT] | o VCC o RX o TX o GND | `---------------------------------' Flashing instructions A) Serial console, U-Boot and TFTP 1. Connect to serial header J1 on the PCB 2. Power on device and enter U-Boot console 3. Set up TFTP server serving an OpenWrt initramfs build 4. Load initramfs build using the command tftpboot in the U-Boot cli 5. Boot the loaded image using the command bootm 6. Copy squashfs OpenWrt sysupgrade build to the booted device 7. Use mtd to write sysupgrade to partition "firmware" 8. Reboot and enjoy B) Experimental factory image flashing over SSH from airOS v6.1.7 1. You need to flash your UBNT M2HP with airOS v6.1.7 firmware no other airOS version is currently supported 2. git clone https://github.com/true-systems/ubnt-bullet-m2hp-openwrt-flashing 3. cd ubnt-bullet-m2hp-openwrt-flashing 4. make flash-factory FW_OWRT=/path/to/your/openwrt-ath79-generic-ubnt_bullet-m-xw-squashfs-factory.bin Tested only on Bullet M2HP. Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-11-17 07:01:55 +00:00
define Device/ubnt_bullet-m-xw
$(Device/ubnt-xw)
DEVICE_TITLE := Ubiquiti Bullet-M (XW)
SUPPORTED_DEVICES += bullet-m-xw
endef
TARGET_DEVICES += ubnt_bullet-m-xw
ath79: fix dts files Add the SoC compatible to the individual dts files. Rename the dts files to match the common pattern. Remove dts files wich aren't used and no image in ar71xx exists. Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-05-08 05:22:38 +00:00
define Device/ubnt_rocket-m
ath79: add new OF only target for QCA MIPS silicon This target aims to replace ar71xx mid-term. The big part that is still missing is making the MMIO/AHB wifi work using OF. NAND and mikrotik subtargets will follow. Signed-off-by: John Crispin <john@phrozen.org>
2018-05-06 08:20:11 +00:00
$(Device/ubnt-xm)
DEVICE_TITLE := Ubiquiti Rocket-M
ath79: add and enforce image metadata Add metadata to images and make the metdata mandatory. Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-05-07 20:41:04 +00:00
SUPPORTED_DEVICES += rocket-m
ath79: add new OF only target for QCA MIPS silicon This target aims to replace ar71xx mid-term. The big part that is still missing is making the MMIO/AHB wifi work using OF. NAND and mikrotik subtargets will follow. Signed-off-by: John Crispin <john@phrozen.org>
2018-05-06 08:20:11 +00:00
endef
ath79: fix dts files Add the SoC compatible to the individual dts files. Rename the dts files to match the common pattern. Remove dts files wich aren't used and no image in ar71xx exists. Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-05-08 05:22:38 +00:00
TARGET_DEVICES += ubnt_rocket-m
ath79: add new OF only target for QCA MIPS silicon This target aims to replace ar71xx mid-term. The big part that is still missing is making the MMIO/AHB wifi work using OF. NAND and mikrotik subtargets will follow. Signed-off-by: John Crispin <john@phrozen.org>
2018-05-06 08:20:11 +00:00
ath79: align naming of Ubiquiti Nanostation M Support for the Nanostation M (XW) was added in 40530c8eb with board name "nanostation-m-xw". The current image for the "Nanostation M" uses "nano-m" as the board name. This commit renames it to the full product name as it's used by all other boards. The legacy boardname of the ar71xx target is added via SUPPORTED_DEVICES to ease switching to ath79 target. Signed-off-by: Sven Roederer <devel-sven@geroedel.de> [touch-ups on the commit message, removed subject remains] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-03-06 23:09:15 +00:00
define Device/ubnt_nanostation-m
ath79: add new OF only target for QCA MIPS silicon This target aims to replace ar71xx mid-term. The big part that is still missing is making the MMIO/AHB wifi work using OF. NAND and mikrotik subtargets will follow. Signed-off-by: John Crispin <john@phrozen.org>
2018-05-06 08:20:11 +00:00
$(Device/ubnt-xm)
ath79: align naming of Ubiquiti Nanostation M Support for the Nanostation M (XW) was added in 40530c8eb with board name "nanostation-m-xw". The current image for the "Nanostation M" uses "nano-m" as the board name. This commit renames it to the full product name as it's used by all other boards. The legacy boardname of the ar71xx target is added via SUPPORTED_DEVICES to ease switching to ath79 target. Signed-off-by: Sven Roederer <devel-sven@geroedel.de> [touch-ups on the commit message, removed subject remains] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-03-06 23:09:15 +00:00
DEVICE_TITLE := Ubiquiti Nanostation M
ath79: add and enforce image metadata Add metadata to images and make the metdata mandatory. Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-05-07 20:41:04 +00:00
SUPPORTED_DEVICES += nano-m
ath79: add new OF only target for QCA MIPS silicon This target aims to replace ar71xx mid-term. The big part that is still missing is making the MMIO/AHB wifi work using OF. NAND and mikrotik subtargets will follow. Signed-off-by: John Crispin <john@phrozen.org>
2018-05-06 08:20:11 +00:00
endef
ath79: align naming of Ubiquiti Nanostation M Support for the Nanostation M (XW) was added in 40530c8eb with board name "nanostation-m-xw". The current image for the "Nanostation M" uses "nano-m" as the board name. This commit renames it to the full product name as it's used by all other boards. The legacy boardname of the ar71xx target is added via SUPPORTED_DEVICES to ease switching to ath79 target. Signed-off-by: Sven Roederer <devel-sven@geroedel.de> [touch-ups on the commit message, removed subject remains] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-03-06 23:09:15 +00:00
TARGET_DEVICES += ubnt_nanostation-m
ath79: add new OF only target for QCA MIPS silicon This target aims to replace ar71xx mid-term. The big part that is still missing is making the MMIO/AHB wifi work using OF. NAND and mikrotik subtargets will follow. Signed-off-by: John Crispin <john@phrozen.org>
2018-05-06 08:20:11 +00:00
ath79: Add support for Ubiquiti Nanostation M (XW) CPU: AR9342 SoC RAM: 64 MB DDR2 Flash: 8 MB NOR SPI Ports: 2x100 MBit (24V PoE in, 24V PoE out), AR8236 switch WLAN: 2.4/5 GHz UART: 1 UART LEDs: Power, 2x Ethernet, 4x RSSI LEDs (orange, red, 2x green) Buttons: Reset Flashing instructions using recovery method over TFTP 1. Unplug the ethernet cable from the router. 2. Using paper clip press and hold the router's reset button. Make sure you can feel it depressed by the paper clip. Do not release the button until step 4. 3. While keeping the reset button pressed in, plug the ethernet cable back into the AP. Keep the reset button depressed until you see the device's LEDs flashing in upgrade mode (alternating LED1/LED3 and LED2/LED4), this may take up to 25 seconds. 4. You may release the reset button, now the device should be in TFTP transfer mode. 5. Set a static IP on your Computer's NIC. A static IP of 192.168.1.25/24 should work. 6. Plug the PoE injector's LAN cable directly to your computer. 7. Start tftp client and issue following commands: tftp> binary tftp> connect 192.168.1.20 tftp> put openwrt-ath79-generic-ubnt-nano-m-xw-squashfs-factory.bin Tested-by: Joe Ayers <ae6xe@arrl.net> Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-12-12 20:09:01 +00:00
define Device/ubnt_nanostation-m-xw
$(Device/ubnt-xw)
DEVICE_TITLE := Ubiquiti Nanostation M (XW)
ath79: align naming of Ubiquiti Nanostation M Support for the Nanostation M (XW) was added in 40530c8eb with board name "nanostation-m-xw". The current image for the "Nanostation M" uses "nano-m" as the board name. This commit renames it to the full product name as it's used by all other boards. The legacy boardname of the ar71xx target is added via SUPPORTED_DEVICES to ease switching to ath79 target. Signed-off-by: Sven Roederer <devel-sven@geroedel.de> [touch-ups on the commit message, removed subject remains] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-03-06 23:09:15 +00:00
SUPPORTED_DEVICES += nano-m-xw
ath79: Add support for Ubiquiti Nanostation M (XW) CPU: AR9342 SoC RAM: 64 MB DDR2 Flash: 8 MB NOR SPI Ports: 2x100 MBit (24V PoE in, 24V PoE out), AR8236 switch WLAN: 2.4/5 GHz UART: 1 UART LEDs: Power, 2x Ethernet, 4x RSSI LEDs (orange, red, 2x green) Buttons: Reset Flashing instructions using recovery method over TFTP 1. Unplug the ethernet cable from the router. 2. Using paper clip press and hold the router's reset button. Make sure you can feel it depressed by the paper clip. Do not release the button until step 4. 3. While keeping the reset button pressed in, plug the ethernet cable back into the AP. Keep the reset button depressed until you see the device's LEDs flashing in upgrade mode (alternating LED1/LED3 and LED2/LED4), this may take up to 25 seconds. 4. You may release the reset button, now the device should be in TFTP transfer mode. 5. Set a static IP on your Computer's NIC. A static IP of 192.168.1.25/24 should work. 6. Plug the PoE injector's LAN cable directly to your computer. 7. Start tftp client and issue following commands: tftp> binary tftp> connect 192.168.1.20 tftp> put openwrt-ath79-generic-ubnt-nano-m-xw-squashfs-factory.bin Tested-by: Joe Ayers <ae6xe@arrl.net> Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-12-12 20:09:01 +00:00
endef
TARGET_DEVICES += ubnt_nanostation-m-xw
ath79: Add support for Ubiquiti LiteAP ac (LAP-120) This commit adds support for the Ubiquiti LiteAP ac (LAP-120), an outdoor 5 GHz AC access point with an integrated 120° 16 dBi antenna. The device was previously known as LiteBeam AP ac but was later rebranded. CPU: Atheros AR9342 SoC RAM: 64 MB DDR2 Flash: 16 MB NOR SPI Ports: 1 GbE port (PoE in) WLAN: 5 GHz QCA899X (PCI) The integrated QCA899X is a Ubiquiti branded part with modified vendor and product id (0777:11ac9). It is very similar to the NanoStation loco AC, except for the 2.4 GHz management radio (missing here). Installation procedure is the same as the NanoStation [loco] AC: 1. Connect to serial header on device 2. Power on device and enter uboot console 3. Set up tftp server serving an openwrt initramfs build 4. Load initramfs build using the command tftpboot in the uboot cli 5. Boot the loaded image using the command bootm 6. Copy squashfs openwrt sysupgrade build to the booted device 7. Use mtd to write sysupgrade to partition "firmware" 8. Reboot and enjoy Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2018-09-19 12:17:35 +00:00
define Device/ubnt_lap-120
$(Device/ubnt-wa)
DEVICE_TITLE := Ubiquiti LiteAP ac (LAP-120)
ar71xx/ath79: switch devices to the -ct driver and firmware Since commit 61b5b4971e7 ("mac80211: make ath10k-ct the default ath10k") select ath10k-ct and the -ct firmwares by default. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-12-17 00:58:49 +00:00
DEVICE_PACKAGES += kmod-ath10k-ct ath10k-firmware-qca988x-ct
ath79: Add support for Ubiquiti LiteAP ac (LAP-120) This commit adds support for the Ubiquiti LiteAP ac (LAP-120), an outdoor 5 GHz AC access point with an integrated 120° 16 dBi antenna. The device was previously known as LiteBeam AP ac but was later rebranded. CPU: Atheros AR9342 SoC RAM: 64 MB DDR2 Flash: 16 MB NOR SPI Ports: 1 GbE port (PoE in) WLAN: 5 GHz QCA899X (PCI) The integrated QCA899X is a Ubiquiti branded part with modified vendor and product id (0777:11ac9). It is very similar to the NanoStation loco AC, except for the 2.4 GHz management radio (missing here). Installation procedure is the same as the NanoStation [loco] AC: 1. Connect to serial header on device 2. Power on device and enter uboot console 3. Set up tftp server serving an openwrt initramfs build 4. Load initramfs build using the command tftpboot in the uboot cli 5. Boot the loaded image using the command bootm 6. Copy squashfs openwrt sysupgrade build to the booted device 7. Use mtd to write sysupgrade to partition "firmware" 8. Reboot and enjoy Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2018-09-19 12:17:35 +00:00
IMAGE_SIZE := 15744k
IMAGE/factory.bin := $$(IMAGE/sysupgrade.bin) | mkubntimage-split
endef
TARGET_DEVICES += ubnt_lap-120
ath79: Add support for Ubiquiti NanoBeam AC The NanoBeam is a small AR9342 based directional 5 GHz AC CPE with hardware almost identical to the Ubiquiti NanoStation AC loco. Over the NanoStation AC loco it has 5 additional LEDs. Four of those LEDs are used as rssi indicators, the fifth LED is used as an ethernet link/activity indicator. CPU: Atheros AR9342 SoC RAM: 64 MB DDR2 Flash: 16 MB NOR SPI WLAN: QCA988X Ports: 1x GbE Flashing procedure is identical to the NanoStation AC loco and can be performed either via serial or the factory firmware upgrade. Serial flashing: 1. Connect to serial header on device (8N1 115200) 2. Power on device and enter uboot console 3. Set up tftp server serving an openwrt initramfs build 4. Load initramfs build using the command tftpboot in the uboot cli 5. Boot the loaded image using the command bootm 6. Copy squashfs openwrt sysupgrade build to the booted device 7. Use mtd to write sysupgrade to partition "firmware" 8. Reboot and enjoy Flashing through factory firmware: 1. Ensure firmware version v8.5.0.36727 is installed. Up/downgrade to this exact version. 2. Patch fwupdate.real binary using `hexdump -Cv /bin/ubntbox | sed 's/14 40 fe fe/00 00 00 00/g' | hexdump -R > /tmp/fwupdate.real` 3. Make the patched fwupdate.real binary executable using `chmod +x /tmp/fwupdate.real` 4. Copy the squashfs factory image to /tmp on the device 5. Flash OpenWRT using `/tmp/fwupdate.real -m <squashfs-factory image>` 6. Wait for the device to reboot Thanks to @cybermaus for testing! Tested-by: Maurits van Dueren den Hollander <cybermaus@gmail.com> Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
2019-01-08 14:27:57 +00:00
define Device/ubnt_nanobeam-ac
$(Device/ubnt-wa)
DEVICE_TITLE := Ubiquiti NanoBeam AC
DEVICE_PACKAGES += kmod-ath10k-ct ath10k-firmware-qca988x-ct
IMAGE_SIZE := 15744k
IMAGE/factory.bin := $$(IMAGE/sysupgrade.bin) | mkubntimage-split
endef
TARGET_DEVICES += ubnt_nanobeam-ac
ath79: Add support for Ubiquiti Nanostation AC 5 GHz AC wireless outdoor PoE CPE with internal 2.4 GHz management radio CPU: Atheros AR9342 SoC RAM: 64 MB DDR2 Flash: 16 MB NOR SPI Switch: QCA8334 Ports: 2 GbE ports (1x PoE in, 1x PoE passthrough) WLAN: 5 GHz QCA899X (PCI) and 2.4 GHZ AR9342 Successor to the old NanoStation M5 with AC wireless. The integrated QCA899X is a Ubiquiti branded part with modified vendor and product id (0777:11ac9). Serial Serial settings: 115200, 8N1 * = plated through hole 0 = nylon screw [Top of device] +--------------------------+ | [label] | | 0 | | 0 | | [ubnt] | | [logo] 3V3 * | | TX * | | RX * | | GND * | | | | * | | * | | * | | * | | 0 | | 0 | | | | | Installation 1. Connect to serial header on device 2. Power on device and enter uboot console 3. Set up tftp server serving an openwrt initramfs build 4. Load initramfs build using the command tftpboot in the uboot cli 5. Boot the loaded image using the command bootm 6. Copy squashfs openwrt sysupgrade build to the booted device 7. Use mtd to write sysupgrade to partition "firmware" 8. Reboot and enjoy Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
2018-09-04 00:08:01 +00:00
define Device/ubnt_nanostation-ac
$(Device/ubnt-wa)
DEVICE_TITLE := Ubiquiti Nanostation AC
ar71xx/ath79: switch devices to the -ct driver and firmware Since commit 61b5b4971e7 ("mac80211: make ath10k-ct the default ath10k") select ath10k-ct and the -ct firmwares by default. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-12-17 00:58:49 +00:00
DEVICE_PACKAGES += kmod-ath10k-ct ath10k-firmware-qca988x-ct
ath79: Add support for Ubiquiti Nanostation AC 5 GHz AC wireless outdoor PoE CPE with internal 2.4 GHz management radio CPU: Atheros AR9342 SoC RAM: 64 MB DDR2 Flash: 16 MB NOR SPI Switch: QCA8334 Ports: 2 GbE ports (1x PoE in, 1x PoE passthrough) WLAN: 5 GHz QCA899X (PCI) and 2.4 GHZ AR9342 Successor to the old NanoStation M5 with AC wireless. The integrated QCA899X is a Ubiquiti branded part with modified vendor and product id (0777:11ac9). Serial Serial settings: 115200, 8N1 * = plated through hole 0 = nylon screw [Top of device] +--------------------------+ | [label] | | 0 | | 0 | | [ubnt] | | [logo] 3V3 * | | TX * | | RX * | | GND * | | | | * | | * | | * | | * | | 0 | | 0 | | | | | Installation 1. Connect to serial header on device 2. Power on device and enter uboot console 3. Set up tftp server serving an openwrt initramfs build 4. Load initramfs build using the command tftpboot in the uboot cli 5. Boot the loaded image using the command bootm 6. Copy squashfs openwrt sysupgrade build to the booted device 7. Use mtd to write sysupgrade to partition "firmware" 8. Reboot and enjoy Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
2018-09-04 00:08:01 +00:00
IMAGE_SIZE := 15744k
IMAGE/factory.bin := $$(IMAGE/sysupgrade.bin) | mkubntimage-split
endef
TARGET_DEVICES += ubnt_nanostation-ac
ath79: Add support for Ubiquiti NanoStation AC loco Atheros AR9342, 16 MB flash, 64 MB RAM Successor to the old NanoStation M5 loco with AC wireless. Includes a mac80211 patch for ath10k_pci because Ubiquiti uses a Ubiquiti branded and customized QCA988X with vendor id 0777 and device id 11ac for AC wireless. Installation 1. Connect to serial header on device (8N1 115200) 2. Power on device and enter uboot console 3. Set up tftp server serving an openwrt initramfs build 4. Load initramfs build using the command tftpboot in the uboot cli 5. Boot the loaded image using the command bootm 6. Copy squashfs openwrt sysupgrade build to the booted device 7. Use mtd to write sysupgrade to partition "firmware" 8. Reboot and enjoy Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
2018-01-23 10:36:41 +00:00
define Device/ubnt_nanostation-ac-loco
$(Device/ubnt-wa)
DEVICE_TITLE := Ubiquiti Nanostation AC loco
ar71xx/ath79: switch devices to the -ct driver and firmware Since commit 61b5b4971e7 ("mac80211: make ath10k-ct the default ath10k") select ath10k-ct and the -ct firmwares by default. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-12-17 00:58:49 +00:00
DEVICE_PACKAGES += kmod-ath10k-ct ath10k-firmware-qca988x-ct
ath79: Add support for Ubiquiti NanoStation AC loco Atheros AR9342, 16 MB flash, 64 MB RAM Successor to the old NanoStation M5 loco with AC wireless. Includes a mac80211 patch for ath10k_pci because Ubiquiti uses a Ubiquiti branded and customized QCA988X with vendor id 0777 and device id 11ac for AC wireless. Installation 1. Connect to serial header on device (8N1 115200) 2. Power on device and enter uboot console 3. Set up tftp server serving an openwrt initramfs build 4. Load initramfs build using the command tftpboot in the uboot cli 5. Boot the loaded image using the command bootm 6. Copy squashfs openwrt sysupgrade build to the booted device 7. Use mtd to write sysupgrade to partition "firmware" 8. Reboot and enjoy Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
2018-01-23 10:36:41 +00:00
IMAGE_SIZE := 15744k
IMAGE/factory.bin := $$(IMAGE/sysupgrade.bin) | mkubntimage-split
endef
TARGET_DEVICES += ubnt_nanostation-ac-loco
ath79: fix dts files Add the SoC compatible to the individual dts files. Rename the dts files to match the common pattern. Remove dts files wich aren't used and no image in ar71xx exists. Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-05-08 05:22:38 +00:00
define Device/ubnt_unifi
ath79: add new OF only target for QCA MIPS silicon This target aims to replace ar71xx mid-term. The big part that is still missing is making the MMIO/AHB wifi work using OF. NAND and mikrotik subtargets will follow. Signed-off-by: John Crispin <john@phrozen.org>
2018-05-06 08:20:11 +00:00
$(Device/ubnt-bz)
DEVICE_TITLE := Ubiquiti UniFi
ath79: add and enforce image metadata Add metadata to images and make the metdata mandatory. Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-05-07 20:41:04 +00:00
SUPPORTED_DEVICES += unifi
ath79: add new OF only target for QCA MIPS silicon This target aims to replace ar71xx mid-term. The big part that is still missing is making the MMIO/AHB wifi work using OF. NAND and mikrotik subtargets will follow. Signed-off-by: John Crispin <john@phrozen.org>
2018-05-06 08:20:11 +00:00
endef
ath79: fix dts files Add the SoC compatible to the individual dts files. Rename the dts files to match the common pattern. Remove dts files wich aren't used and no image in ar71xx exists. Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-05-08 05:22:38 +00:00
TARGET_DEVICES += ubnt_unifi
ath79: add ubiquiti unifi ap ac lite/lr Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
2018-06-05 12:38:02 +00:00
ath79: sync naming of Ubiquiti devices Use a Unifi AC Lite board-/image name consistent with other Ubiquiti devices. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2018-06-27 10:10:33 +00:00
define Device/ubnt_unifiac
ath79: add support for Ubiquiti UniFi AC-Pro rework the dts to a common unifi-ac dtsi pro network is connected via phy0 and has usb ports lite network is connected via phy4 without usb ports Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
2018-06-26 07:30:46 +00:00
ATH_SOC := qca9563
ath79: add ubiquiti unifi ap ac lite/lr Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
2018-06-05 12:38:02 +00:00
IMAGE_SIZE := 7744k
mac80211: make ath10k-ct the default ath10k We select ath10k-ct by default, but it is still possible to build the upstream version. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John Crispin <john@phrozen.org>
2018-09-05 12:51:44 +00:00
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
ath79: add ubiquiti unifi ap ac lite/lr Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
2018-06-05 12:38:02 +00:00
endef
ath79: sync naming of Ubiquiti devices Use a Unifi AC Lite board-/image name consistent with other Ubiquiti devices. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2018-06-27 10:10:33 +00:00
define Device/ubnt_unifiac-lite
$(Device/ubnt_unifiac)
ath79: add ubiquiti unifi ap ac lite/lr Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
2018-06-05 12:38:02 +00:00
DEVICE_TITLE := Ubiquiti UniFi AC-Lite
ath79: correct ar71xx boardname for UniFi AC Lite This corrects the additional boardname for the image metadata to the one used in ar71xx. The previously present additional entry was never used on a running system. Reviewed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit 1a256470e78a90ac97f41e3335b3fc6ee827e4bc) Signed-off-by: David Bauer <mail@david-bauer.net>
2019-10-14 09:16:54 +00:00
SUPPORTED_DEVICES += unifiac-lite
ath79: add ubiquiti unifi ap ac lite/lr Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
2018-06-05 12:38:02 +00:00
endef
ath79: sync naming of Ubiquiti devices Use a Unifi AC Lite board-/image name consistent with other Ubiquiti devices. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2018-06-27 10:10:33 +00:00
TARGET_DEVICES += ubnt_unifiac-lite
ath79: add support for Ubiquiti UniFi AC-Pro rework the dts to a common unifi-ac dtsi pro network is connected via phy0 and has usb ports lite network is connected via phy4 without usb ports Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
2018-06-26 07:30:46 +00:00
ath79: add support for Unifi AC Mesh The Unifi AC Mesh is equivalent to the Unifi AC Lite. However, for setting certain parameters with the flashed device it is helpful that the devices know their variant (e.g. automatically setting antenna gain for the different antennas in Lite and Mesh). Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2018-06-27 12:33:40 +00:00
define Device/ubnt_unifiac-mesh
$(Device/ubnt_unifiac)
DEVICE_TITLE := Ubiquiti UniFi AC-Mesh
SUPPORTED_DEVICES += ubnt-unifiac-mesh
endef
TARGET_DEVICES += ubnt_unifiac-mesh
ath79: add support for UniFi AC-Mesh Pro The Unifi AC-Mesh Pro has identical hardware to the Unifi AC-Pro except USB support. Furthermore for setting parameters like antenna gain it is helpful to know the exact device variant. Signed-off-by: Christoph Krapp <achterin@googlemail.com>
2018-07-02 12:39:54 +00:00
define Device/ubnt_unifiac-mesh-pro
$(Device/ubnt_unifiac)
DEVICE_TITLE := Ubiquiti UniFi AC-Mesh Pro
SUPPORTED_DEVICES += ubnt-unifiac-mesh-pro
endef
TARGET_DEVICES += ubnt_unifiac-mesh-pro
ath79: add support for Ubiquiti UniFi AC-Pro rework the dts to a common unifi-ac dtsi pro network is connected via phy0 and has usb ports lite network is connected via phy4 without usb ports Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
2018-06-26 07:30:46 +00:00
define Device/ubnt_unifiac-pro
$(Device/ubnt_unifiac)
DEVICE_TITLE := Ubiquiti UniFi AC-Pro
DEVICE_PACKAGES += kmod-usb-core kmod-usb2
SUPPORTED_DEVICES += ubnt-unifiac-pro
endef
TARGET_DEVICES += ubnt_unifiac-pro
ath79: initial support for Ubiquiti RouterStation and RouterStation Pro This adds a shared ar7161_ubnt_routerstation.dtsi as well as two other .dts files that utilize it, ar7161_ubnt_routerstation.dts and ar7161_ubnt_routerstation-pro.dts. The modifications to generic-ubnt.mk, config-default, and base-files necessary for image generation, parsing RedBoot FIS partitions, network configuration, and sysupgrade are also included. This reintroduces vital bits from platform_do_upgrade_combined() and its supporting functions to /lib/upgrade/platform.sh, which were previously removed from ath79 in 3e9d9f62258f80298710441e0db557e59e152dcf "ath79: sysupgrade: drop unused platform checks". The new function is called "routerstation_do_upgrade" and will *only* work for the RouterStation series of boards. It does however retain the ability to downgrade (e.g. from master -> 17.01.x using sysupgrade -F). All hardware is functional including the AR8216 switch (for the Pro), wireless via ath5k/ath9k using the miniPCI slots, flash, USB, button, and LED. Switch and LAN/WAN configuration is the same as it is with the equivalent ar71xx targets. MAC addresses are assigned based upon the content stored in the RedBoot config partition. Flashing via both sysupgrade and TFTP has been confirmed to work. Also, the initramfs images are now raw .bin files instead of being wrapped in a uImage (as they currently are in ar71xx), which makes them bootable with RedBoot. One notable difference to ar71xx is the inclusion of the RedBoot "fconfig" utility (analogous to U-Boot’s fw_printenv/fw_setenv) in DEVICE_PACKAGES. The FIS partitions are probed using the RedBoot MTD parser’s DT binding, whose proper usage is mutually exclusive to defining a separate fixed-partitions node for "RedBoot config". This config partition contains the board's base MAC address. The lack of a hard-coded flash location means that the mtd-mac-address property cannot be used in the .dts, so instead fconfig is used to read the MAC addresses from flash in userspace during first boot. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl> Signed-off-by: Matt Merhar <mattmerhar@protonmail.com>
2018-08-27 13:59:09 +00:00
define Device/ubnt_routerstation_common
DEVICE_PACKAGES := -kmod-ath9k -wpad-mini -uboot-envtools kmod-usb-ohci kmod-usb2 fconfig
ATH_SOC := ar7161
IMAGE_SIZE := 16128k
ath79: remove duplicate image build variables Remove image build variables which are set to the same value as the default image build recipe. Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-06 11:07:56 +00:00
IMAGES += factory.bin
ath79: initial support for Ubiquiti RouterStation and RouterStation Pro This adds a shared ar7161_ubnt_routerstation.dtsi as well as two other .dts files that utilize it, ar7161_ubnt_routerstation.dts and ar7161_ubnt_routerstation-pro.dts. The modifications to generic-ubnt.mk, config-default, and base-files necessary for image generation, parsing RedBoot FIS partitions, network configuration, and sysupgrade are also included. This reintroduces vital bits from platform_do_upgrade_combined() and its supporting functions to /lib/upgrade/platform.sh, which were previously removed from ath79 in 3e9d9f62258f80298710441e0db557e59e152dcf "ath79: sysupgrade: drop unused platform checks". The new function is called "routerstation_do_upgrade" and will *only* work for the RouterStation series of boards. It does however retain the ability to downgrade (e.g. from master -> 17.01.x using sysupgrade -F). All hardware is functional including the AR8216 switch (for the Pro), wireless via ath5k/ath9k using the miniPCI slots, flash, USB, button, and LED. Switch and LAN/WAN configuration is the same as it is with the equivalent ar71xx targets. MAC addresses are assigned based upon the content stored in the RedBoot config partition. Flashing via both sysupgrade and TFTP has been confirmed to work. Also, the initramfs images are now raw .bin files instead of being wrapped in a uImage (as they currently are in ar71xx), which makes them bootable with RedBoot. One notable difference to ar71xx is the inclusion of the RedBoot "fconfig" utility (analogous to U-Boot’s fw_printenv/fw_setenv) in DEVICE_PACKAGES. The FIS partitions are probed using the RedBoot MTD parser’s DT binding, whose proper usage is mutually exclusive to defining a separate fixed-partitions node for "RedBoot config". This config partition contains the board's base MAC address. The lack of a hard-coded flash location means that the mtd-mac-address property cannot be used in the .dts, so instead fconfig is used to read the MAC addresses from flash in userspace during first boot. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl> Signed-off-by: Matt Merhar <mattmerhar@protonmail.com>
2018-08-27 13:59:09 +00:00
IMAGE/factory.bin := append-rootfs | pad-rootfs | mkubntimage | check-size $$$$(IMAGE_SIZE)
ath79: image: append metadata to routerstations and ja76pf2 images This target enforces metadata check so add the necessary information. It was previously removed because md5 sum check. When using these sysupgrade images on ar71xx target the check would complain about them not matching. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl> (cherry picked from commit 077d06a1a5a23caae4d0c53afb60913955d2a3ea)
2019-08-23 13:50:49 +00:00
IMAGE/sysupgrade.bin := append-rootfs | pad-rootfs | combined-image | append-metadata | check-size $$$$(IMAGE_SIZE)
ath79: routerstation: prepare to use sysupgrade-tar format image In PR [1] introducing initial support for Ubiquiti RouterStation boards, Mathias Kresin suggested to replace the combined sysupgrade image with tarball generated by sysupgrade-tar.sh. This would simplify deployment of sysupgrade as the kernel size (needed to update FIS partition) could be simply calculated on the fly instead of reading value from combined image header. Unfortunately this would break sysupgrade compatibility between ar71xx image and ath79 image. Therefore this commit creates migration path to use new sysuprade image, it adds code to accept both of them at this moment. The plan is to keep it until new stable version is released. Then the image recipe should be changed to new format and compatibility code for old image removed. 1. https://github.com/openwrt/openwrt/pull/1237 Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-03-04 14:14:18 +00:00
# IMAGE/sysupgrade.bin := append-rootfs | pad-rootfs | check-size $$$$(IMAGE_SIZE) | sysupgrade-tar rootfs=$$$$@ | append-metadata
ath79: initial support for Ubiquiti RouterStation and RouterStation Pro This adds a shared ar7161_ubnt_routerstation.dtsi as well as two other .dts files that utilize it, ar7161_ubnt_routerstation.dts and ar7161_ubnt_routerstation-pro.dts. The modifications to generic-ubnt.mk, config-default, and base-files necessary for image generation, parsing RedBoot FIS partitions, network configuration, and sysupgrade are also included. This reintroduces vital bits from platform_do_upgrade_combined() and its supporting functions to /lib/upgrade/platform.sh, which were previously removed from ath79 in 3e9d9f62258f80298710441e0db557e59e152dcf "ath79: sysupgrade: drop unused platform checks". The new function is called "routerstation_do_upgrade" and will *only* work for the RouterStation series of boards. It does however retain the ability to downgrade (e.g. from master -> 17.01.x using sysupgrade -F). All hardware is functional including the AR8216 switch (for the Pro), wireless via ath5k/ath9k using the miniPCI slots, flash, USB, button, and LED. Switch and LAN/WAN configuration is the same as it is with the equivalent ar71xx targets. MAC addresses are assigned based upon the content stored in the RedBoot config partition. Flashing via both sysupgrade and TFTP has been confirmed to work. Also, the initramfs images are now raw .bin files instead of being wrapped in a uImage (as they currently are in ar71xx), which makes them bootable with RedBoot. One notable difference to ar71xx is the inclusion of the RedBoot "fconfig" utility (analogous to U-Boot’s fw_printenv/fw_setenv) in DEVICE_PACKAGES. The FIS partitions are probed using the RedBoot MTD parser’s DT binding, whose proper usage is mutually exclusive to defining a separate fixed-partitions node for "RedBoot config". This config partition contains the board's base MAC address. The lack of a hard-coded flash location means that the mtd-mac-address property cannot be used in the .dts, so instead fconfig is used to read the MAC addresses from flash in userspace during first boot. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl> Signed-off-by: Matt Merhar <mattmerhar@protonmail.com>
2018-08-27 13:59:09 +00:00
KERNEL := kernel-bin | append-dtb | lzma | pad-to $$(BLOCKSIZE)
KERNEL_INITRAMFS := kernel-bin | append-dtb
endef
define Device/ubnt_routerstation
$(Device/ubnt_routerstation_common)
DEVICE_TITLE := Ubiquiti RouterStation
UBNT_BOARD := RS
UBNT_TYPE := RSx
UBNT_CHIP := ar7100
DEVICE_PACKAGES += -swconfig
ath79: image: add supported string for routerstations and ja76pf2 Now that the md5 check is fixed and metadata present, sysupgrade on ar71xx will complain about device not being supported by the image. Since the cause is not matching strings for supported devices add them accordingly. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl> (cherry picked from commit a45cf75eca4069f24bf5bba8f245de2e553f7f78)
2019-08-23 13:50:50 +00:00
SUPPORTED_DEVICES += routerstation
ath79: initial support for Ubiquiti RouterStation and RouterStation Pro This adds a shared ar7161_ubnt_routerstation.dtsi as well as two other .dts files that utilize it, ar7161_ubnt_routerstation.dts and ar7161_ubnt_routerstation-pro.dts. The modifications to generic-ubnt.mk, config-default, and base-files necessary for image generation, parsing RedBoot FIS partitions, network configuration, and sysupgrade are also included. This reintroduces vital bits from platform_do_upgrade_combined() and its supporting functions to /lib/upgrade/platform.sh, which were previously removed from ath79 in 3e9d9f62258f80298710441e0db557e59e152dcf "ath79: sysupgrade: drop unused platform checks". The new function is called "routerstation_do_upgrade" and will *only* work for the RouterStation series of boards. It does however retain the ability to downgrade (e.g. from master -> 17.01.x using sysupgrade -F). All hardware is functional including the AR8216 switch (for the Pro), wireless via ath5k/ath9k using the miniPCI slots, flash, USB, button, and LED. Switch and LAN/WAN configuration is the same as it is with the equivalent ar71xx targets. MAC addresses are assigned based upon the content stored in the RedBoot config partition. Flashing via both sysupgrade and TFTP has been confirmed to work. Also, the initramfs images are now raw .bin files instead of being wrapped in a uImage (as they currently are in ar71xx), which makes them bootable with RedBoot. One notable difference to ar71xx is the inclusion of the RedBoot "fconfig" utility (analogous to U-Boot’s fw_printenv/fw_setenv) in DEVICE_PACKAGES. The FIS partitions are probed using the RedBoot MTD parser’s DT binding, whose proper usage is mutually exclusive to defining a separate fixed-partitions node for "RedBoot config". This config partition contains the board's base MAC address. The lack of a hard-coded flash location means that the mtd-mac-address property cannot be used in the .dts, so instead fconfig is used to read the MAC addresses from flash in userspace during first boot. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl> Signed-off-by: Matt Merhar <mattmerhar@protonmail.com>
2018-08-27 13:59:09 +00:00
endef
TARGET_DEVICES += ubnt_routerstation
define Device/ubnt_routerstation-pro
$(Device/ubnt_routerstation_common)
DEVICE_TITLE := Ubiquiti RouterStation Pro
UBNT_BOARD := RSPRO
UBNT_TYPE := RSPRO
UBNT_CHIP := ar7100pro
ath79: image: add supported string for routerstations and ja76pf2 Now that the md5 check is fixed and metadata present, sysupgrade on ar71xx will complain about device not being supported by the image. Since the cause is not matching strings for supported devices add them accordingly. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl> (cherry picked from commit a45cf75eca4069f24bf5bba8f245de2e553f7f78)
2019-08-23 13:50:50 +00:00
SUPPORTED_DEVICES += routerstation-pro
ath79: initial support for Ubiquiti RouterStation and RouterStation Pro This adds a shared ar7161_ubnt_routerstation.dtsi as well as two other .dts files that utilize it, ar7161_ubnt_routerstation.dts and ar7161_ubnt_routerstation-pro.dts. The modifications to generic-ubnt.mk, config-default, and base-files necessary for image generation, parsing RedBoot FIS partitions, network configuration, and sysupgrade are also included. This reintroduces vital bits from platform_do_upgrade_combined() and its supporting functions to /lib/upgrade/platform.sh, which were previously removed from ath79 in 3e9d9f62258f80298710441e0db557e59e152dcf "ath79: sysupgrade: drop unused platform checks". The new function is called "routerstation_do_upgrade" and will *only* work for the RouterStation series of boards. It does however retain the ability to downgrade (e.g. from master -> 17.01.x using sysupgrade -F). All hardware is functional including the AR8216 switch (for the Pro), wireless via ath5k/ath9k using the miniPCI slots, flash, USB, button, and LED. Switch and LAN/WAN configuration is the same as it is with the equivalent ar71xx targets. MAC addresses are assigned based upon the content stored in the RedBoot config partition. Flashing via both sysupgrade and TFTP has been confirmed to work. Also, the initramfs images are now raw .bin files instead of being wrapped in a uImage (as they currently are in ar71xx), which makes them bootable with RedBoot. One notable difference to ar71xx is the inclusion of the RedBoot "fconfig" utility (analogous to U-Boot’s fw_printenv/fw_setenv) in DEVICE_PACKAGES. The FIS partitions are probed using the RedBoot MTD parser’s DT binding, whose proper usage is mutually exclusive to defining a separate fixed-partitions node for "RedBoot config". This config partition contains the board's base MAC address. The lack of a hard-coded flash location means that the mtd-mac-address property cannot be used in the .dts, so instead fconfig is used to read the MAC addresses from flash in userspace during first boot. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl> Signed-off-by: Matt Merhar <mattmerhar@protonmail.com>
2018-08-27 13:59:09 +00:00
endef
TARGET_DEVICES += ubnt_routerstation-pro
ath79: add support for Ubiquiti airCube ISP The Ubiquiti Network airCube ISP is a cube shaped 2.4 GHz with internal 2x2 MIMO antennas. It can be supplied via a USB connector or via PoE. There are for 10/100 Mbps ports (1 * WAN + 3 * LAN). There is an optional PoE passthrough from the first LAN port to the WAN port. SoC: Qualcomm / Atheros QCA9533-BL3A RAM: 64 MB DDR2 Flash: 16 MB SPI NOR Ethernet: 4x 10/100 Mbps (1 WAN + 3 LAN) LEDS: 1x via a SPI controller (not yet supported) Buttons: 1x Reset Serial: 1x (only RX and TX); 115200 baud, 8N1 Missing points: - LED not yet supported - Factory upgrade via web IF or TFTP recovery not yet supported (Needs RSA signed images, for details see PR#1958) The serial port is on a four pin connextor labeled J1 and located between Ethernet and USB connector. The pinout is: 1. 3V3 (out) 2. Rx (in) 3. Tx (out) 4. GND Upgrading via serial port / U-Boot: - Connect the serial port via a level converter - Power the system and stop U-Boot with pressing any key when `Hit any key to stop autoboot` is displayed. Note: Pressing space multiple times untill U-Boot reaches that location works well. - Connect a PC with the IP 192.168.1.100 (or some other in that net) running a TFTP-Server to one of the LAN ports. Copy the sysupgrade image to the server. - Set the U-Boot server IP with setenv serverip 192.168.1.100 - Load the flash image to RAM with tftpboot 0x81000000 sysupgrade.bin - Erase the flash with erase 0x9f050000 0x9ffaffff - Write the new flash content with cp 0x81000000 0x9f050000 ${filesize} - Reset the device with reset Signed-off-by: Christian Mauderer <oss@c-mauderer.de> [removed full stop in subject and added lockdown note to commit message] Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-03-15 20:02:54 +00:00
define Device/ubnt_acb-isp
$(Device/ubnt)
ATH_SOC := qca9533
IMAGE_SIZE := 15744k
DEVICE_TITLE := Ubiquiti airCube ISP
UBNT_BOARD := ACB-ISP
UBNT_TYPE := ACB
UBNT_CHIP := qca9533
IMAGES := sysupgrade.bin
endef
TARGET_DEVICES += ubnt_acb-isp
Reference in New Issue Copy Permalink