openwrt/target/linux/ramips/dts/UBNT-ERX-SFP.dts

/dts-v1/;

#include "UBNT-ER-e50.dtsi"

#include <dt-bindings/gpio/gpio.h>

/ {
	model = "UBNT-ERX-SFP";
	compatible = "ubiquiti,edgerouterx-sfp", "mediatek,mt7621-soc";

	i2c-gpio {
		compatible = "i2c-gpio";
		gpios = <&gpio0 3 GPIO_ACTIVE_HIGH /* sda */
		         &gpio0 4 GPIO_ACTIVE_HIGH /* scl */
		        >;
		#address-cells = <1>;
		#size-cells = <0>;

		pca9555@25 {
			compatible = "pca9555";
			reg = <0x25>;
		};
	};
};
ramips: add support for Ubiquiti EdgeRouter X-SFP This patch adds support for the Ubiquiti EdgeRouter X-SFP and improves support for the EdgeRouter X (PoE-passthrough). Specification: - SoC: MediaTek MT7621AT - Flash: 256 MiB - RAM: 265 MiB - Ethernet: 5 x LAN (1000 Mbps) - UART: 1 x UART on PCB (3.3V, RX, TX, GND) - 57600 8N1 - EdgeRouter X: - 1 x PoE-Passtrough (Eth4) - powered by Wallwart or passive PoE - EdgeRouter X-SFP: - 5 x PoE-Out (24V, passive) - 1 x SFP (unknown status) - powered by Wallwart (24V) Doesn't work: * SoC has crypto engine but no open driver. * SoC has nat acceleration, but no open driver. * This router has 2MB spi flash soldered in but MT nand/spi drivers do not support pin sharing, so it is not accessable and disabled. Stock firmware could read it and it was empty. Installation via vendor firmware: - build an Initrd-image (> 3MiB) and upload the factory-image - initrd can have luci-mod-failsafe - flash final firmware via LuCI / sysupgrade on rebooted system via TFTP: - stop uboot into tftp-load into option "1" - upload factory.bin image Signed-off-by: Sven Roederer <devel-sven@geroedel.de> 2017-05-29 09:24:49 +00:00			`/dts-v1/;`

			`#include "UBNT-ER-e50.dtsi"`

			`#include <dt-bindings/gpio/gpio.h>`

			`/ {`
			`model = "UBNT-ERX-SFP";`
ramips: add missing soc compatibles to dts Add SoC compatibles where missing. Signed-off-by: Mathias Kresin <dev@kresin.me> 2017-12-30 19:41:22 +00:00			`compatible = "ubiquiti,edgerouterx-sfp", "mediatek,mt7621-soc";`
ramips: add support for Ubiquiti EdgeRouter X-SFP This patch adds support for the Ubiquiti EdgeRouter X-SFP and improves support for the EdgeRouter X (PoE-passthrough). Specification: - SoC: MediaTek MT7621AT - Flash: 256 MiB - RAM: 265 MiB - Ethernet: 5 x LAN (1000 Mbps) - UART: 1 x UART on PCB (3.3V, RX, TX, GND) - 57600 8N1 - EdgeRouter X: - 1 x PoE-Passtrough (Eth4) - powered by Wallwart or passive PoE - EdgeRouter X-SFP: - 5 x PoE-Out (24V, passive) - 1 x SFP (unknown status) - powered by Wallwart (24V) Doesn't work: * SoC has crypto engine but no open driver. * SoC has nat acceleration, but no open driver. * This router has 2MB spi flash soldered in but MT nand/spi drivers do not support pin sharing, so it is not accessable and disabled. Stock firmware could read it and it was empty. Installation via vendor firmware: - build an Initrd-image (> 3MiB) and upload the factory-image - initrd can have luci-mod-failsafe - flash final firmware via LuCI / sysupgrade on rebooted system via TFTP: - stop uboot into tftp-load into option "1" - upload factory.bin image Signed-off-by: Sven Roederer <devel-sven@geroedel.de> 2017-05-29 09:24:49 +00:00
			`i2c-gpio {`
			`compatible = "i2c-gpio";`
			`gpios = <&gpio0 3 GPIO_ACTIVE_HIGH /* sda */`
			`&gpio0 4 GPIO_ACTIVE_HIGH /* scl */`
			`>;`
			`#address-cells = <1>;`
			`#size-cells = <0>;`

			`pca9555@25 {`
			`compatible = "pca9555";`
			`reg = <0x25>;`
			`};`
			`};`
			`};`