openwrt/target/linux/ipq806x/base-files/etc/init.d/bootcount

24 lines
365 B
Plaintext
Raw Normal View History

mtd: base-files: Unify dual-firmware devices (Linksys) Consistently handle boot-count reset and upgrade across ipq40xx, ipq806x, kirkwood, mvebu Dual-firmware devices often utilize a specific MTD partition to record the number of times the boot loader has initiated boot. Most of these devices are NAND, typically with a 2k erase size. When this code was ported to the ipq40xx platform, the device in hand used NOR for this partition, with a 16-byte "record" size. As the implementation of `mtd resetbc` is by-platform, the hard-coded nature of this change prevented proper operation of a NAND-based device. * Unified the "NOR" variant with the rest of the Linksys variants * Added logging to indicate success and failure * Provided a meaningful return value for scripting * "Protected" the use of `mtd resetbc` in start-up scripts so that failure does not end the boot sequence * Moved Linksys-specific actions into common `/etc/init.d/bootcount` For upgrade, these devices need to determine which partition to flash, as well as set certain U-Boot envirnment variables to change the next boot to the newly flashed version. * Moved upgrade-related environment changes out of bootcount * Combined multiple flashes of environment into single one * Current-partition detection now handles absence of `boot_part` Runtime-tested: Linksys EA8300 Signed-off-by: Jeff Kletsky <git-commits@allycomm.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [checkpatch.pl fixes, traded split strings for 80+ chars per line]
2019-04-10 15:28:01 +00:00
#!/bin/sh /etc/rc.common
START=99
. "$IPKG_INSTROOT/lib/upgrade/asrock.sh"
ipq806x: add support for ASRock G10 The ASRock G10 is a 2.4/5 GHz band 11ac "Gaming" router, based on Qualcomm IPQ8064. Specifications: SoC: Qualcomm IPQ8064 CPU: Dual-Core A15 @ (384 - 1,400 MHz, 2C2T) DRAM: 512 MiB (~467 MiB available) NAND: 128 MB (Micron MT29F1G08ABBEAH4) WLAN0: 4T4R 5 GHz Wlan (QCA9980) WLAN1: 4T4R 2.4 GHz Wlan (QCA9980) ETH: 5x 10/100/1000 Mbps Ethernet (QCA8337) INPUT: Reset Button, WPS 2.4G and WPS 5G Button LEDS: 1 multicolor status LED USB: 2x USB 3.0 Type-A POWER: 12VDC/3A AC Adapter + dedicated Power Switch UART: Setting is 115200-8-N-1. 1x4 .1" unpopulated header on the PCB (J6 - very tiny silkscreen next to TX). Pinout: 1. 3v3 (Square - best skipped!), 2. RX, 3. GND, 4. TX WARNING: The serial port needs a TTL/RS-232 3.3v level converter! (Depending on the serial adapter RX and TX might need to be swapped). Note about the IR-Remote: There's a 8-Bit MCU (SONIX SN8F25E21SG) which is controlling the IR-Remote and is fed by the IR-Photodiode. The SoC can talk to the device via I2C. The vendor's GPL archive comes with the source of the interface driver for this as a (character driver), the main control software is however a blob. Installation Instructions: 1. Download factory image to disk 2. Apply factory image via stock web-gui Back to stock: 1. Login to router via ssh 2. run "asrock_g10_back_to_factory" script from /sbin Notes: - If something goes wrong durring sysupgrade, router will go back to factory image. - Asrock G10 uses partition layout from smem. So partition layout can be normal or alternate. - 900-arm-add-cmdline-override.patch was copied from 102-powerpc-add-cmdline-override.patch from powerpc target. Knowledge about BOOTCONFIG partition was based on user "jmomo" post from old OpenWrt forum (Post #50): https://forum.archive.openwrt.org/viewtopic.php?id=65956&p=2 Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [bump to 5.4, add factory image, fix sysupgrade, convert partition layout to smem, remove ipq-wifi-asrock-g10 and use ART, minor fixes] Co-Authored-by: Pawel Dembicki <paweldembicki@gmail.com> Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> Tested-by: Lukasz Ostapiuk <palibrzuch@gmail.com>
2019-10-11 22:49:15 +00:00
boot() {
mtd: base-files: Unify dual-firmware devices (Linksys) Consistently handle boot-count reset and upgrade across ipq40xx, ipq806x, kirkwood, mvebu Dual-firmware devices often utilize a specific MTD partition to record the number of times the boot loader has initiated boot. Most of these devices are NAND, typically with a 2k erase size. When this code was ported to the ipq40xx platform, the device in hand used NOR for this partition, with a 16-byte "record" size. As the implementation of `mtd resetbc` is by-platform, the hard-coded nature of this change prevented proper operation of a NAND-based device. * Unified the "NOR" variant with the rest of the Linksys variants * Added logging to indicate success and failure * Provided a meaningful return value for scripting * "Protected" the use of `mtd resetbc` in start-up scripts so that failure does not end the boot sequence * Moved Linksys-specific actions into common `/etc/init.d/bootcount` For upgrade, these devices need to determine which partition to flash, as well as set certain U-Boot envirnment variables to change the next boot to the newly flashed version. * Moved upgrade-related environment changes out of bootcount * Combined multiple flashes of environment into single one * Current-partition detection now handles absence of `boot_part` Runtime-tested: Linksys EA8300 Signed-off-by: Jeff Kletsky <git-commits@allycomm.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [checkpatch.pl fixes, traded split strings for 80+ chars per line]
2019-04-10 15:28:01 +00:00
case $(board_name) in
ipq806x: add support for ASRock G10 The ASRock G10 is a 2.4/5 GHz band 11ac "Gaming" router, based on Qualcomm IPQ8064. Specifications: SoC: Qualcomm IPQ8064 CPU: Dual-Core A15 @ (384 - 1,400 MHz, 2C2T) DRAM: 512 MiB (~467 MiB available) NAND: 128 MB (Micron MT29F1G08ABBEAH4) WLAN0: 4T4R 5 GHz Wlan (QCA9980) WLAN1: 4T4R 2.4 GHz Wlan (QCA9980) ETH: 5x 10/100/1000 Mbps Ethernet (QCA8337) INPUT: Reset Button, WPS 2.4G and WPS 5G Button LEDS: 1 multicolor status LED USB: 2x USB 3.0 Type-A POWER: 12VDC/3A AC Adapter + dedicated Power Switch UART: Setting is 115200-8-N-1. 1x4 .1" unpopulated header on the PCB (J6 - very tiny silkscreen next to TX). Pinout: 1. 3v3 (Square - best skipped!), 2. RX, 3. GND, 4. TX WARNING: The serial port needs a TTL/RS-232 3.3v level converter! (Depending on the serial adapter RX and TX might need to be swapped). Note about the IR-Remote: There's a 8-Bit MCU (SONIX SN8F25E21SG) which is controlling the IR-Remote and is fed by the IR-Photodiode. The SoC can talk to the device via I2C. The vendor's GPL archive comes with the source of the interface driver for this as a (character driver), the main control software is however a blob. Installation Instructions: 1. Download factory image to disk 2. Apply factory image via stock web-gui Back to stock: 1. Login to router via ssh 2. run "asrock_g10_back_to_factory" script from /sbin Notes: - If something goes wrong durring sysupgrade, router will go back to factory image. - Asrock G10 uses partition layout from smem. So partition layout can be normal or alternate. - 900-arm-add-cmdline-override.patch was copied from 102-powerpc-add-cmdline-override.patch from powerpc target. Knowledge about BOOTCONFIG partition was based on user "jmomo" post from old OpenWrt forum (Post #50): https://forum.archive.openwrt.org/viewtopic.php?id=65956&p=2 Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [bump to 5.4, add factory image, fix sysupgrade, convert partition layout to smem, remove ipq-wifi-asrock-g10 and use ART, minor fixes] Co-Authored-by: Pawel Dembicki <paweldembicki@gmail.com> Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> Tested-by: Lukasz Ostapiuk <palibrzuch@gmail.com>
2019-10-11 22:49:15 +00:00
asrock,g10)
asrock_bootconfig_mangle "bootcheck" && reboot
ipq806x: add support for ASRock G10 The ASRock G10 is a 2.4/5 GHz band 11ac "Gaming" router, based on Qualcomm IPQ8064. Specifications: SoC: Qualcomm IPQ8064 CPU: Dual-Core A15 @ (384 - 1,400 MHz, 2C2T) DRAM: 512 MiB (~467 MiB available) NAND: 128 MB (Micron MT29F1G08ABBEAH4) WLAN0: 4T4R 5 GHz Wlan (QCA9980) WLAN1: 4T4R 2.4 GHz Wlan (QCA9980) ETH: 5x 10/100/1000 Mbps Ethernet (QCA8337) INPUT: Reset Button, WPS 2.4G and WPS 5G Button LEDS: 1 multicolor status LED USB: 2x USB 3.0 Type-A POWER: 12VDC/3A AC Adapter + dedicated Power Switch UART: Setting is 115200-8-N-1. 1x4 .1" unpopulated header on the PCB (J6 - very tiny silkscreen next to TX). Pinout: 1. 3v3 (Square - best skipped!), 2. RX, 3. GND, 4. TX WARNING: The serial port needs a TTL/RS-232 3.3v level converter! (Depending on the serial adapter RX and TX might need to be swapped). Note about the IR-Remote: There's a 8-Bit MCU (SONIX SN8F25E21SG) which is controlling the IR-Remote and is fed by the IR-Photodiode. The SoC can talk to the device via I2C. The vendor's GPL archive comes with the source of the interface driver for this as a (character driver), the main control software is however a blob. Installation Instructions: 1. Download factory image to disk 2. Apply factory image via stock web-gui Back to stock: 1. Login to router via ssh 2. run "asrock_g10_back_to_factory" script from /sbin Notes: - If something goes wrong durring sysupgrade, router will go back to factory image. - Asrock G10 uses partition layout from smem. So partition layout can be normal or alternate. - 900-arm-add-cmdline-override.patch was copied from 102-powerpc-add-cmdline-override.patch from powerpc target. Knowledge about BOOTCONFIG partition was based on user "jmomo" post from old OpenWrt forum (Post #50): https://forum.archive.openwrt.org/viewtopic.php?id=65956&p=2 Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [bump to 5.4, add factory image, fix sysupgrade, convert partition layout to smem, remove ipq-wifi-asrock-g10 and use ART, minor fixes] Co-Authored-by: Pawel Dembicki <paweldembicki@gmail.com> Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> Tested-by: Lukasz Ostapiuk <palibrzuch@gmail.com>
2019-10-11 22:49:15 +00:00
;;
ipq806x: add Edgecore ECW5410 support This patch adds support for the Edgecore ECW5410 indoor AP. Specification: - SoC: Qualcomm Atheros IPQ8068 ARMv7 2x Cortex A-15 - RAM: 256MB(225 usable) DDR3 - NOR Flash: 16MB SPI NOR - NAND Flash: 128MB S34MS01G2 Parallel NAND - Ethernet: 2 x 1G via 2x AR8033 PHY-s connected directly to GMAC2 and GMAC3 via SGMII (802.3af POE IN on eth0) - USB: 1 x USB 3.0 SuperSpeed - WLAN: 2x QCA9994 AC Wawe 2 (1x 2GHz bgn, 1x 5GHz acn) - CC2540 BLE - UART console on RJ45 next to ethernet ports exposed. Its Cisco pin compatible, 115200 8n1 baud. Installation instructions: Through stock firmware or initramfs. 1.Connect to console 2. Login with root account, if password is unknown then interrupt the boot with f and reset it in failsafe. 3. Transfer factory image 4. Flash the image with ubiformat /dev/mtd1 -y -f <your factory image path> This will replace the rootfs2 with OpenWrt, if you are currently running from rootfs2 then simply change /dev/mtd1 to /dev/mtd0 Note Initramfs: 1. Connect to console 2. Transfer the image from TFTP server with tftpboot, or by using DHCP advertised image with dhcp command. 3. bootm 4. Run ubiformat /dev/mtd1 You need to interrupt the bootloader after rebooting and run: run altbootcmd This will switch your active rootfs partition to one you wrote to and boot from it. So if rootfs1 is active, then it will change it to rootfs2. This will format the rootfs2 partition, if your active partition is 2 then simply change /dev/mtd1 with /dev/mtd0 If you dont format the partition you will be writing too, then sysupgrade will find existing UBI rootfs and kernel volumes and update those. This will result in wrong ordering and OpenWrt will panic on boot. 5. Transfer sysupgrade image 6. Flash with sysupgrade -n. Note that sysupgrade will write the image to rootfs partition that is not currently in use. Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2020-09-07 10:43:37 +00:00
edgecore,ecw5410)
fw_setenv bootcount 0
;;
ipq806x: add support for Extreme Networks AP3935 Extreme Networks AP3935i/e - https://www.extremenetworks.com/support/documentation/access-points-ap3935i-e/ SoC: IPQ8068 QYY AT46279K45060I RAM: NANYA 1527 NT5CC256M16DP-DI 515073W0EF 7 TW FLASH: NOR - S25FL256S1 - 32MB NAND - Macronix MX30UF4G28AB - 512MB LAN: Atheros AR8035-A J5150WL 1515 CN - RGMII LAN2: Atheros AR8033-AL1A SKCSR.AJ1 1444 China - SGMII WLAN2: QCA9990 OVV FNPV209 K451406 WLAN5: QCA9990 OVV FNPV209 K451406 SERIAL: RS232 Port (115200 8n1) Cisco console cable and 4pin Serial Header | 3.3 | GND | RX | TX MAC address for LAN1/LAN2/WLAN 2G/WLAN 5G in uboot env * Installation via either RJ45 console or on-board 4 PIN header Install Method -------------- 1) Setup TFTP server, and place openwrt-ipq806x-generic-extreme_ap3935-initramfs-uImage image in /srv/tftp or similar 2) Connect to console on router and connect ethernet port "LAN1" to your LAN 3) Interupt the boot with any character 4) Login with admin/new2day for default password (use reset/FactoryDefault if password needs to be reset) 5) Set serverip to TFTP IP: set serverip 192.168.1.2 6) Set ipaddr to another IP: set ipaddr 192.168.1.101 7) Make uboot ping something to activate eth0 on boot: set bootcmd 'ping 192.168.1.1; run boot_flash' saveenv 8) TFTP image to RAM: tftpboot 0x42000000 openwrt-ipq806x-generic-extreme_ap3935i-initramfs-uImage 9) Boot image: bootm 0x42000000 In OpenWRT, "LAN1" is LAN, "LAN2" is WAN 10) SFTP openwrt-ipq806x-generic-extreme_ap3935-squashfs-nand-sysupgrade.bin image to /tmp 11) sysupgrade /tmp/openwrt-*-nand-sysupgrade.bin Signed-off-by: Glen Lee <g2lee@yahoo.com>
2023-06-29 19:58:05 +00:00
extreme,ap3935)
fw_setenv WATCHDOG_COUNT 0x00000000
;;
ipq806x: add support for Linksys EA7500 V1 This patch adds support for the Linksys EA7500 V1 router. Specification: - CPU: Qualcomm IPQ8064 - RAM: 256MB - Flash: NAND 128MB - WiFi: QCA9982 an+ac + QCA9983 bgn - Ethernet: 5 GBE Ports (WAN+ 4xLAN) (QCA8337) - USB: 1x USB 3.0 1x USB2.0 - Serial console: RJ-45 115200 8n1 (1V8 Voltage level) - 2 Buttons - 1 LED Known issues: - Some devices won't flash via web gui Installation: - Newer stock images doesn't allow to install custom firmware. - Please downgrade software to 1.1.2 version. Official firmware: https://downloads.linksys.com/downloads/firmware/FW_EA7500_1.1.2.172843_prod.gpg.img - Do it two times to downgrade all stored images. - Apply factory image via web-gui. Serial + TFTP method: - downgrade to 1.1.2 two times - connect ehternet and serial cable - set ip address of tftp server to 192.168.1.254 - put openwrt factory image to tftp folder and rename it to macan.bin - stop device while booting in u-boot - run command: "run flashimg" - run command: "setenv boot_part 1" - run command "saveenv" - reset Back to stock: - Please use old non-gpg image like this 1.1.2: https://downloads.linksys.com/downloads/firmware/FW_EA7500_1.1.2.172843_prod.img - ssh to router and copy image to tmp - use sysupgrade -n -F Tested by github users: @jack338c and @grzesiczek1 Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> [removed i2c4_pins, mdio0_pins, nand_pins, rgmii2_pins from DTSI] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-26 19:14:11 +00:00
linksys,ea7500-v1 |\
mtd: base-files: Unify dual-firmware devices (Linksys) Consistently handle boot-count reset and upgrade across ipq40xx, ipq806x, kirkwood, mvebu Dual-firmware devices often utilize a specific MTD partition to record the number of times the boot loader has initiated boot. Most of these devices are NAND, typically with a 2k erase size. When this code was ported to the ipq40xx platform, the device in hand used NOR for this partition, with a 16-byte "record" size. As the implementation of `mtd resetbc` is by-platform, the hard-coded nature of this change prevented proper operation of a NAND-based device. * Unified the "NOR" variant with the rest of the Linksys variants * Added logging to indicate success and failure * Provided a meaningful return value for scripting * "Protected" the use of `mtd resetbc` in start-up scripts so that failure does not end the boot sequence * Moved Linksys-specific actions into common `/etc/init.d/bootcount` For upgrade, these devices need to determine which partition to flash, as well as set certain U-Boot envirnment variables to change the next boot to the newly flashed version. * Moved upgrade-related environment changes out of bootcount * Combined multiple flashes of environment into single one * Current-partition detection now handles absence of `boot_part` Runtime-tested: Linksys EA8300 Signed-off-by: Jeff Kletsky <git-commits@allycomm.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [checkpatch.pl fixes, traded split strings for 80+ chars per line]
2019-04-10 15:28:01 +00:00
linksys,ea8500)
mtd resetbc s_env || true
;;
esac
}