openwrt/package/broadcom-57xx/Makefile

# 
# Copyright (C) 2006 OpenWrt.org
#
# This is free software, licensed under the GNU General Public License v2.
# See /LICENSE for more information.
#
# $Id: Makefile 8694 2007-09-08 19:55:42Z nbd $

include $(TOPDIR)/rules.mk
include $(INCLUDE_DIR)/kernel.mk

PKG_NAME:=broadcom-57xx
PKG_RELEASE:=1

include $(INCLUDE_DIR)/package.mk

define KernelPackage/brcm-57xx
  SUBMENU:=Network Devices
  DEPENDS:=@TARGET_brcm_2_4 +kmod-switch
  TITLE:=Broadcom 57xx ethernet support
  FILES:=$(PKG_BUILD_DIR)/bcm57xx.$(LINUX_KMOD_SUFFIX)
  AUTOLOAD:=$(call AutoLoad,30,bcm57xx)
endef

define Build/Prepare
	mkdir -p $(PKG_BUILD_DIR)
	$(CP) ./src/* $(PKG_BUILD_DIR)/
endef

ifeq ($(BOARD),brcm-2.4)
	BUILDFLAGS = -DBCMDRIVER -I$(LINUX_DIR)/arch/mips/bcm947xx/include -I$(STAGING_DIR)/usr/include
	BUILDFLAGS += -DDBG=0 -DBCM_PROC_FS=1 -DT3_JUMBO_RCV_RCB_ENTRY_COUNT=256 -DNICE_SUPPORT
	BUILDFLAGS += -DPCIX_TARGET_WORKAROUND=1 -DINCLUDE_TBI_SUPPORT=1 -DINCLUDE_5701_AX_FIX=1
endif

define Build/Compile
	$(MAKE) -C "$(LINUX_DIR)" \
		CROSS_COMPILE="$(TARGET_CROSS)" \
		ARCH="$(LINUX_KARCH)" \
		SUBDIRS="$(PKG_BUILD_DIR)" \
		EXTRA_CFLAGS="$(BUILDFLAGS)" \
		modules
endef

define KernelPackage/brcm-57xx/install
	$(call Package/brcm-57xx/install/Default,$(1))
	#$(INSTALL_DIR) $(1)/etc/modules.d
	#echo "bcm57xx activate_gpio=1" > $(1)/etc/modules.d/30-bcm57xx
endef

$(eval $(call KernelPackage,brcm-57xx))
(6/6) bcm57xx: package This is the bcm57xx package. I have tested default vlan functions, but I dont have the equipment to test more advanced setups. The default vlan setup seems to be working fine. I also added the activate_gpio parameter which will make the driver activate the switch via gpio before probing for it. I'm not sure which method is best for autoload. For the wrt350n, I need the activate_gpio parameter. But its probably not a good idea to add that to the autoload file. On a system without a bcm57xx switch, isn't it a bad idea to mess with the gpios looking for the switch? Ideally, wouldn't it be best to load the bcm57xx module from broadcom-diag, after it has determined which router its on? I tried using 'request_module' from there, but had no success. For now, I am relying on preinit to load the bcm57xx module with activate_gpio param, after it has failed to load switch_robo and switch_adm. Signed-off-by: Ben Pfountz <netprince (at) vt (dot) edu> SVN-Revision: 11471 2008-06-15 11:11:28 +00:00			`#`
			`# Copyright (C) 2006 OpenWrt.org`
			`#`
			`# This is free software, licensed under the GNU General Public License v2.`
			`# See /LICENSE for more information.`
			`#`
			`# $Id: Makefile 8694 2007-09-08 19:55:42Z nbd $`

			`include $(TOPDIR)/rules.mk`
			`include $(INCLUDE_DIR)/kernel.mk`

			`PKG_NAME:=broadcom-57xx`
			`PKG_RELEASE:=1`

			`include $(INCLUDE_DIR)/package.mk`

			`define KernelPackage/brcm-57xx`
			`SUBMENU:=Network Devices`
			`DEPENDS:=@TARGET_brcm_2_4 +kmod-switch`
			`TITLE:=Broadcom 57xx ethernet support`
			`FILES:=$(PKG_BUILD_DIR)/bcm57xx.$(LINUX_KMOD_SUFFIX)`
			`AUTOLOAD:=$(call AutoLoad,30,bcm57xx)`
			`endef`

			`define Build/Prepare`
			`mkdir -p $(PKG_BUILD_DIR)`
			`$(CP) ./src/* $(PKG_BUILD_DIR)/`
			`endef`

			`ifeq ($(BOARD),brcm-2.4)`
			`BUILDFLAGS = -DBCMDRIVER -I$(LINUX_DIR)/arch/mips/bcm947xx/include -I$(STAGING_DIR)/usr/include`
			`BUILDFLAGS += -DDBG=0 -DBCM_PROC_FS=1 -DT3_JUMBO_RCV_RCB_ENTRY_COUNT=256 -DNICE_SUPPORT`
			`BUILDFLAGS += -DPCIX_TARGET_WORKAROUND=1 -DINCLUDE_TBI_SUPPORT=1 -DINCLUDE_5701_AX_FIX=1`
			`endif`

			`define Build/Compile`
			`$(MAKE) -C "$(LINUX_DIR)" \`
			`CROSS_COMPILE="$(TARGET_CROSS)" \`
			`ARCH="$(LINUX_KARCH)" \`
			`SUBDIRS="$(PKG_BUILD_DIR)" \`
			`EXTRA_CFLAGS="$(BUILDFLAGS)" \`
			`modules`
			`endef`

			`define KernelPackage/brcm-57xx/install`
			`$(call Package/brcm-57xx/install/Default,$(1))`
			`#$(INSTALL_DIR) $(1)/etc/modules.d`
			`#echo "bcm57xx activate_gpio=1" > $(1)/etc/modules.d/30-bcm57xx`
			`endef`

			`$(eval $(call KernelPackage,brcm-57xx))`