openwrt/target/linux/ath79/dts/qca9558_tplink_archer-d7b-v1.dts

79 lines
1.2 KiB
Plaintext
Raw Normal View History

ath79: add support for TP-Link Archer D7/D7b v1 TP-Link Archer D7 v1 is a dual-band AC1750 router + modem. The router section is based on Qualcomm/Atheros QCA9558 + QCA9880. The "DSL" section is based on BCM6318 but it's currently not supported. The Archer D7b seems to differ from the Archer D7 only in the partition table. Router section - Specification: 775/650/258 MHz (CPU/DDR/AHB) 128 MB of RAM (DDR2) 16 MB of FLASH (SPI NOR) 3T3R 2.4 GHz 3T3R 5 GHz 4x 10/100/1000 Mbps Ethernet 7x LED, 2x button UART header on PCB Known issues: - Broadband LED (missing GPIO - probably driven by the BCM6318) - Internet LED (missing GPIO - probably driven by the BCM6318) - WIFI LED (working only for one interface at a time, while in the OEM firmware works for both wifi interfaces; thus, this patch does not set a trigger by default) - DSL not working (eth0) UART connection --------------- J1 HEADER (Qualcomm CPU) . VCC . GND . RX O TX J41 HEADER (Broadcom CPU) . VCC . GND . RX O TX The following instructions require a connection to the J1 UART header and are tested for the Archer D7 v1. For the Archer D7b v1, names should be changed accordingly. Flash instructions under U-Boot, using UART ------------------------------------------ 1. Press "tpl" to stop autobooting and obtain U-Boot CLI access. 2. Setup ip addresses for U-Boot and your tftp server. 3. Issue below commands: tftpboot 0x81000000 openwrt-ath79-generic-tplink_archer-d7-v1-squashfs-sysupgrade.bin erase 0x9f020000 +f90000 cp.b 0x81000000 0x9f020000 0xf90000 reset Initramfs instructions under U-Boot for testing, using UART ---------------------------------------------------------- 1. Press "tpl" to stop autobooting and obtain U-Boot CLI access. 2. Setup ip addresses for U-Boot and your tftp server. 3. Issue below commands: tftpboot 0x81000000 openwrt-ath79-generic-tplink_archer-d7-v1-initramfs-kernel.bin bootm 0x81000000 4. Here you can backup the original firmware and/or flash the sysupgrade openwrt if you want Restore the original firmware ----------------------------- 0. Backup every partition using the OpenWrt web interface 1. Download the OEM firmware from the TP-Link website 2. Extract the bin file in a folder (eg. Archer_D7v1_1.6.0_0.9.1_up_boot(160216)_2016-02-16_15.55.48.bin) 3. Remove the U-Boot and the Broadcom image part from the file. Issue the following command: dd if="Archer_D7v1_1.6.0_0.9.1_up_boot(160216)_2016-02-16_15.55.48.bin" of="Archer_D7v1_1.6.0_0.9.1_up_boot(160216)_2016-02-16_15.55.48.bin.mod" skip=257 bs=512 count=31872 4. Double check the .mod file size. It must be 16318464 bytes. 5. Flash it using the OpenWrt web interface. Force the update if needed. WARNING: Remember to NOT keep settings. 5b. (Alternative to 5.) Flash it using the U-Boot and UART connection. Issue below commands in the U-Boot: tftpboot 0x81000000 Archer_D7v1_1.6.0_0.9.1_up_boot(160216)_2016-02-16_15.55.48.bin.mod erase 0x9f020000 +f90000 cp.b 0x81000000 0x9f020000 0xf90000 reset Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com> [cosmetic DTS changes, remove TPLINK_HWREVADD := 0, do not use two phyXtpt at once, add missing buttons, minor commit message adjustments] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-01-19 20:05:31 +00:00
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
#include "qca9558_tplink_archer-d7.dtsi"
/ {
compatible = "tplink,archer-d7b-v1", "qca,qca9558";
model = "TP-Link Archer D7b v1";
aliases {
label-mac-device = &wmac;
};
};
&spi {
status = "okay";
flash@0 {
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <25000000>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "u-boot";
reg = <0x000000 0x020000>;
read-only;
};
partition@20000 {
compatible = "tplink,firmware";
label = "firmware";
reg = <0x020000 0xfa0000>;
};
partition@fc0000 {
label = "config";
reg = <0xfc0000 0x010000>;
read-only;
};
romfs: partition@fd0000 {
label = "romfs";
reg = <0xfd0000 0x010000>;
read-only;
};
partition@fe0000 {
label = "reserve";
reg = <0xfe0000 0x010000>;
read-only;
};
art: partition@ff0000 {
label = "art";
reg = <0xff0000 0x010000>;
read-only;
};
};
};
};
&eth0 {
mtd-mac-address = <&romfs 0xf100>;
mtd-mac-address-increment = <1>;
};
&eth1 {
mtd-mac-address = <&romfs 0xf100>;
};
&wmac {
mtd-cal-data = <&art 0x1000>;
mtd-mac-address = <&romfs 0xf100>;
};