openwrt/target/linux/ath79/dts/ar7240_ubnt_bullet-m-ar7240.dts

// SPDX-License-Identifier: GPL-2.0-or-later OR MIT

#include "ar7240.dtsi"
#include "ar724x_ubnt_xm.dtsi"
#include "ar724x_ubnt_xm_outdoor.dtsi"

/ {
	compatible = "ubnt,bullet-m-ar7240", "ubnt,xm", "qca,ar7240";
	model = "Ubiquiti Bullet M (XM AR7240)";
};

&eth0 {
	fixed-link {
		speed = <100>;
		full-duplex;
	};
};

&eth1 {
	compatible = "syscon", "simple-mfd";
};
ath79: add support for ubnt_bullet-m-ar7240 variant This adds support for the Ubiquiti Bullet M (AR7240). Specifications: - AR7240 SoC @ 400 MHz - 32 MB RAM - 8 MB SPI flash - 1x 10/100 Mbps Ethernet, 24 Vdc PoE-in - External antenna - POWER/LAN green LEDs - 4x RSSI LEDs (red, orange, green, green) - UART (115200 8N1) on PCB Flashing via WebUI: Upload the factory image via the stock firmware web UI. Attention: airOS firmware versions >= 5.6 have a new bootloader with an incompatible partition table! Please downgrade to <= 5.5 _before_ flashing OpenWrt! Refer to the device's Wiki page for further information. Flashing via TFTP: Same procedure as other Ubiquiti M boards. - Use a pointy tool (e.g., pen cap, paper clip) and keep the reset button on the device or on the PoE supply pressed - Power on the device via PoE (keep reset button pressed) - Keep pressing until LEDs flash alternatively LED1+LED3 => LED2+LED4 => LED1+LED3, etc. - Release reset button - The device starts a TFTP server at 192.168.1.20 - Set a static IP on the computer (e.g., 192.168.1.21/24) - Upload via tftp the factory image: $ tftp 192.168.1.20 tftp> bin tftp> trace tftp> put openwrt-ath79-generic-xxxxx-ubnt_bullet-m-ar7240-squashfs-factory.bin The "fixed-link" section of the device tree is needed to avoid errors like this: Generic PHY mdio.0:1f:04: Master/Slave resolution failed, maybe conflicting manual settings? With "fixed-link", the errors go away and eth0 comes up reliably. Signed-off-by: Russell Senior <russell@personaltelco.net> [fix SUPPORTED_DEVICES] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> 2020-03-19 11:27:28 +00:00			`// SPDX-License-Identifier: GPL-2.0-or-later OR MIT`

			`#include "ar7240.dtsi"`
			`#include "ar724x_ubnt_xm.dtsi"`
			`#include "ar724x_ubnt_xm_outdoor.dtsi"`

			`/ {`
			`compatible = "ubnt,bullet-m-ar7240", "ubnt,xm", "qca,ar7240";`
ath79: harmonize model names for Ubiquiti devices This harmonizes the model names for the ath79 Ubiquiti devices by applying a few minor cosmetic adjustments: - Removes hyphens where they are not found in the product names (Ubiquiti uses hyphens only for the abbreviated version names like UAP-AC-PRO which we don't use anyway.) - Add (XM) suffix for DTS model strings to help with distinguishing them from their XW counterparts. - Remove DEVICE_VARIANT for LAP-120 which actually was an alternate device name. - Generally make DTS model names and those from generic-ubnt.mk more consistent. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> 2020-07-15 16:41:57 +00:00			`model = "Ubiquiti Bullet M (XM AR7240)";`
ath79: add support for ubnt_bullet-m-ar7240 variant This adds support for the Ubiquiti Bullet M (AR7240). Specifications: - AR7240 SoC @ 400 MHz - 32 MB RAM - 8 MB SPI flash - 1x 10/100 Mbps Ethernet, 24 Vdc PoE-in - External antenna - POWER/LAN green LEDs - 4x RSSI LEDs (red, orange, green, green) - UART (115200 8N1) on PCB Flashing via WebUI: Upload the factory image via the stock firmware web UI. Attention: airOS firmware versions >= 5.6 have a new bootloader with an incompatible partition table! Please downgrade to <= 5.5 _before_ flashing OpenWrt! Refer to the device's Wiki page for further information. Flashing via TFTP: Same procedure as other Ubiquiti M boards. - Use a pointy tool (e.g., pen cap, paper clip) and keep the reset button on the device or on the PoE supply pressed - Power on the device via PoE (keep reset button pressed) - Keep pressing until LEDs flash alternatively LED1+LED3 => LED2+LED4 => LED1+LED3, etc. - Release reset button - The device starts a TFTP server at 192.168.1.20 - Set a static IP on the computer (e.g., 192.168.1.21/24) - Upload via tftp the factory image: $ tftp 192.168.1.20 tftp> bin tftp> trace tftp> put openwrt-ath79-generic-xxxxx-ubnt_bullet-m-ar7240-squashfs-factory.bin The "fixed-link" section of the device tree is needed to avoid errors like this: Generic PHY mdio.0:1f:04: Master/Slave resolution failed, maybe conflicting manual settings? With "fixed-link", the errors go away and eth0 comes up reliably. Signed-off-by: Russell Senior <russell@personaltelco.net> [fix SUPPORTED_DEVICES] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> 2020-03-19 11:27:28 +00:00			`};`

			`&eth0 {`
			`fixed-link {`
			`speed = <100>;`
			`full-duplex;`
			`};`
			`};`

			`&eth1 {`
			`compatible = "syscon", "simple-mfd";`
			`};`