openwrt/target/linux/ramips/dts/mt7621_phicomm_k2p.dts

146 lines
2.1 KiB
Plaintext
Raw Normal View History

/dts-v1/;
#include "mt7621.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
/ {
compatible = "phicomm,k2p", "mediatek,mt7621-soc";
model = "Phicomm K2P";
aliases {
led-boot = &led_blue;
led-failsafe = &led_blue;
led-running = &led_blue;
led-upgrade = &led_blue;
};
leds {
compatible = "gpio-leds";
stat_r {
label = "k2p:red:status";
gpios = <&gpio 13 GPIO_ACTIVE_HIGH>;
};
stat_y {
label = "k2p:yellow:status";
gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
};
led_blue: stat_b {
label = "k2p:blue:status";
gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
};
};
keys {
compatible = "gpio-keys";
reset {
label = "reset";
gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
linux,code = <KEY_RESTART>;
};
};
};
&spi0 {
status = "okay";
flash@0 {
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <10000000>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "u-boot";
reg = <0x0 0x30000>;
read-only;
};
partition@30000 {
label = "u-boot-env";
reg = <0x30000 0x10000>;
read-only;
};
factory: partition@40000 {
label = "factory";
reg = <0x40000 0x10000>;
read-only;
};
partition@50000 {
label = "permanent_config";
reg = <0x50000 0x50000>;
read-only;
};
partition@a0000 {
compatible = "denx,uimage";
label = "firmware";
reg = <0xa0000 0xf60000>;
};
};
};
};
&pcie {
status = "okay";
};
&pcie0 {
mt76@0,0 {
reg = <0x0000 0 0 0 0>;
mediatek,mtd-eeprom = <&factory 0x0>;
};
};
&gmac0 {
ramips: clean and improve MAC address setup in 02_network This patch removes unnecessary MAC address setup statements in ramips' 02_network by doing several optimizations: 1. For the following devices, lan_mac was set up with mtd_get_mac_binary although the same address was set in DTS. The lan_mac statement is removed in 02_network, but wan_mac is kept: - mercury,mac1200r-v2 - phicomm,k2g - skylab,skw92a - wiznet,wizfi630a 2. For the following devices, wan_mac was set up with mtd_get_mac_binary although the same address was set in DTS. The wan_mac statement is removed in 02_network, no lan_mac is present: - buffalo,whr-g300n - glinet,gl-mt300n-v2 - zyxel,keenetic-start 3. For the following device, lan_mac and wan_mac were set up with mtd_get_mac_binary to the same address as set in DTS. Both statements are removed in 02_network: - buffalo,whr-600d 4. For some devices, it was possible to move setup from 02_network to DTS by introducing previously missing mtd_mac_address: - buffalo,whr-1166d - buffalo,whr-300hp2 - buffalo,wsr-600dhp - ohyeah,oy-0001 - planex,vr500 5. For one device, mtd_mac_address was just wrong and overwritten by 02_network. Put the correct value in DTS and remove redundant statement in 02_network: - asus,rt-ac57u 6. For one device, MAC address defined in DTS is exchanged together with lan_mac/wan_mac setup in 02_network, so that cases in 02_network can be merged: - phicomm,k2p For some devices, an empty case has to be used to prevent them from falling into the default case and have WAN address = eth0 address + 1 set to them. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-08-12 11:21:05 +00:00
mtd-mac-address = <&factory 0xe000>;
};
&switch0 {
ports {
port@0 {
status = "okay";
label = "lan1";
};
port@1 {
status = "okay";
label = "lan2";
};
port@2 {
status = "okay";
label = "lan3";
};
port@3 {
status = "okay";
label = "lan4";
};
port@4 {
status = "okay";
label = "wan";
mtd-mac-address = <&factory 0xe006>;
};
};
};
&state_default {
gpio {
groups = "i2c", "jtag";
function = "gpio";
};
};