openwrt/target/linux/ramips/dts/mt7620a_trendnet_tew-810dr.dts

167 lines
2.7 KiB
Plaintext
Raw Normal View History

ramips: add support for TRENDnet TEW-810DR Specifications: * MediaTek MT7620A (580 Mhz) * 8 MB of FLASH * 64 MB of RAM * 2.4Ghz and 5.0Ghz radios * 5x 10/100 Mbps Ethernet (1 WAN and 4 LAN) * UART header on PCB (57600 8n1) * Green/Orange Power LEDs illuminating a Power-Button Lens * Green/Orange Internet LEDs GPIO controlled illuminating a Globe/Internet Lens * 3x button - wps, power and reset * U-boot bootloader Installation: The sysupgrade.bin image is reported to be OEM web flashed with an ncc_att_hwid appended. ncc_att_hwid is a 32bit binary in the GPL Source download for either the TEW-810DR or DIR-810L and is located at source/user/wolf/cameo/ncc/hostTools. The invocation is: ncc_att_hwid -f tew-810dr-squashfs-factory.bin -a -m "TEW-810DR" -H "1.0R" -r "WW" -c "1.0" This may need to be altered if your hardware version is "1.1R". The image can also be directly flashed via serial tftp: 1. Load *.sysupgrade.bin to your tftp server directory and rename for convenience. 2. Set a static ip 192.168.10.100. 3. NIC cable to a lan port. 4. Serial connection parameters 57600,8N1 5. Power on the TEW-810 and press 4 for a u-boot command line prompt. 6. Verify IP's with U-Boot command "printenv". 7. Adjust tftp settings if needed per the tftp documentation 8. Boot the tftp image to test the build. 9. If the image loads, reset your server ip to 192.168.1.10 and restart network. 10. Log in to Luci, 192.168.1.1, and flash the *sysupgrade.bin image. Notes: The only valid MAC address is found in 0x28 of the factory partition. Other typical offsets/caldata only contain example data: 00:11:22:00:0f:xx Signed-off-by: J. Scott Heppler <shep971@centurylink.net> [remove "link rx tx" in 01_leds, format and extend commit message, fix DTS led node names] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-26 01:24:40 +00:00
//SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/dts-v1/;
#include "mt7620a.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
/ {
compatible = "trendnet,tew-810dr", "ralink,mt7620a-soc";
model = "TRENDnet TEW-810DR";
aliases {
led-boot = &led_power_green;
led-failsafe = &led_power_green;
led-running = &led_power_green;
led-upgrade = &led_power_green;
label-mac-device = &ethernet;
};
keys {
compatible = "gpio-keys";
reset {
label = "reset";
gpios = <&gpio0 1 GPIO_ACTIVE_LOW>;
linux,code = <KEY_RESTART>;
};
wps {
label = "wps";
gpios = <&gpio0 2 GPIO_ACTIVE_LOW>;
linux,code = <KEY_WPS_BUTTON>;
};
};
leds {
compatible = "gpio-leds";
led_power_green: power_green {
label = "tew-810dr:green:power";
gpios = <&gpio0 9 GPIO_ACTIVE_HIGH>;
};
wan_orange {
label = "tew-810dr:orange:wan";
gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
};
wan_green {
label = "tew-810dr:green:wan";
gpios = <&gpio2 0 GPIO_ACTIVE_LOW>;
};
power_orange {
label = "tew-810dr:orange:power";
gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>;
};
};
};
&spi0 {
status = "okay";
flash@0 {
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <50000000>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "u-boot";
reg = <0x0 0x30000>;
read-only;
};
partition@30000 {
label = "u-boot-env";
reg = <0x30000 0x10000>;
read-only;
};
factory: partition@40000 {
label = "factory";
reg = <0x40000 0x10000>;
read-only;
};
factory5g: partition@50000 {
label = "factory5g";
reg = <0x50000 0x10000>;
read-only;
};
partition@60000 {
label = "Wolf_Config";
reg = <0x60000 0x10000>;
read-only;
};
partition@70000 {
label = "MyDlink";
reg = <0x70000 0x80000>;
read-only;
};
partition@f0000 {
label = "Jffs2";
reg = <0xf0000 0x80000>;
read-only;
};
partition@170000 {
compatible = "denx,uimage";
label = "firmware";
reg = <0x170000 0x690000>;
};
};
};
};
&state_default {
gpio {
groups = "i2c", "uartf", "ephy";
function = "gpio";
};
};
&ethernet {
mtd-mac-address = <&factory 0x28>;
mediatek,portmap = "llllw";
};
&gsw {
mediatek,port4 = "ephy";
};
&pcie {
status = "okay";
};
&wmac {
pinctrl-names = "default";
pinctrl-0 = <&pa_pins>;
ralink,mtd-eeprom = <&factory 0x0>;
mtd-mac-address = <&factory 0x28>;
};
&pcie0 {
wifi@0,0 {
reg = <0x0000 0 0 0 0>;
mediatek,mtd-eeprom = <&factory 0x8000>;
ieee80211-freq-limit = <5000000 6000000>;
mtd-mac-address = <&factory 0x28>;
mtd-mac-address-increment = <2>;
};
};
&gpio2 {
status = "okay";
};