ExternalVendorCode/openwrt
1
0
Fork 0
mirror of https://github.com/openwrt/openwrt.git synced 2024-12-24 15:56:49 +00:00
Code Issues Actions 5 Packages Projects Releases Wiki Activity
14334c222e
openwrt/target/linux/ath79/dts/ar9342_ubnt_nanostation-m-xw.dts

32 lines
446 B
Plaintext
Raw Normal View History

ath79: Add support for Ubiquiti Nanostation M (XW) CPU: AR9342 SoC RAM: 64 MB DDR2 Flash: 8 MB NOR SPI Ports: 2x100 MBit (24V PoE in, 24V PoE out), AR8236 switch WLAN: 2.4/5 GHz UART: 1 UART LEDs: Power, 2x Ethernet, 4x RSSI LEDs (orange, red, 2x green) Buttons: Reset Flashing instructions using recovery method over TFTP 1. Unplug the ethernet cable from the router. 2. Using paper clip press and hold the router's reset button. Make sure you can feel it depressed by the paper clip. Do not release the button until step 4. 3. While keeping the reset button pressed in, plug the ethernet cable back into the AP. Keep the reset button depressed until you see the device's LEDs flashing in upgrade mode (alternating LED1/LED3 and LED2/LED4), this may take up to 25 seconds. 4. You may release the reset button, now the device should be in TFTP transfer mode. 5. Set a static IP on your Computer's NIC. A static IP of 192.168.1.25/24 should work. 6. Plug the PoE injector's LAN cable directly to your computer. 7. Start tftp client and issue following commands: tftp> binary tftp> connect 192.168.1.20 tftp> put openwrt-ath79-generic-ubnt-nano-m-xw-squashfs-factory.bin Tested-by: Joe Ayers <ae6xe@arrl.net> Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-12-12 20:09:01 +00:00
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
#include "ar9342_ubnt_xw.dtsi"
/ {
compatible = "ubnt,nanostation-m-xw", "ubnt,xw", "qca,ar9342";
model = "Ubiquiti Nanostation M (XW)";
};
&mdio0 {
status = "okay";
phy4-mii-enable;
ath79: harmonize ethernet-phy naming scheme A minority of ethernet-phy definitions seems to use numbers in label, name and reg property relatively random. This patch aligns their use to have the same numeric value for all of them. While at it, improve order of properties/add newlines for the ethX nodes where necessary. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-01-27 13:15:56 +00:00
phy0: ethernet-phy@0 {
ath79: Add support for Ubiquiti Nanostation M (XW) CPU: AR9342 SoC RAM: 64 MB DDR2 Flash: 8 MB NOR SPI Ports: 2x100 MBit (24V PoE in, 24V PoE out), AR8236 switch WLAN: 2.4/5 GHz UART: 1 UART LEDs: Power, 2x Ethernet, 4x RSSI LEDs (orange, red, 2x green) Buttons: Reset Flashing instructions using recovery method over TFTP 1. Unplug the ethernet cable from the router. 2. Using paper clip press and hold the router's reset button. Make sure you can feel it depressed by the paper clip. Do not release the button until step 4. 3. While keeping the reset button pressed in, plug the ethernet cable back into the AP. Keep the reset button depressed until you see the device's LEDs flashing in upgrade mode (alternating LED1/LED3 and LED2/LED4), this may take up to 25 seconds. 4. You may release the reset button, now the device should be in TFTP transfer mode. 5. Set a static IP on your Computer's NIC. A static IP of 192.168.1.25/24 should work. 6. Plug the PoE injector's LAN cable directly to your computer. 7. Start tftp client and issue following commands: tftp> binary tftp> connect 192.168.1.20 tftp> put openwrt-ath79-generic-ubnt-nano-m-xw-squashfs-factory.bin Tested-by: Joe Ayers <ae6xe@arrl.net> Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-12-12 20:09:01 +00:00
reg = <0>;
phy-mode = "mii";
};
};
&eth0 {
status = "okay";
ath79: harmonize ethernet-phy naming scheme A minority of ethernet-phy definitions seems to use numbers in label, name and reg property relatively random. This patch aligns their use to have the same numeric value for all of them. While at it, improve order of properties/add newlines for the ethX nodes where necessary. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-01-27 13:15:56 +00:00
phy-handle = <&phy0>;
ath79: Add support for Ubiquiti Nanostation M (XW) CPU: AR9342 SoC RAM: 64 MB DDR2 Flash: 8 MB NOR SPI Ports: 2x100 MBit (24V PoE in, 24V PoE out), AR8236 switch WLAN: 2.4/5 GHz UART: 1 UART LEDs: Power, 2x Ethernet, 4x RSSI LEDs (orange, red, 2x green) Buttons: Reset Flashing instructions using recovery method over TFTP 1. Unplug the ethernet cable from the router. 2. Using paper clip press and hold the router's reset button. Make sure you can feel it depressed by the paper clip. Do not release the button until step 4. 3. While keeping the reset button pressed in, plug the ethernet cable back into the AP. Keep the reset button depressed until you see the device's LEDs flashing in upgrade mode (alternating LED1/LED3 and LED2/LED4), this may take up to 25 seconds. 4. You may release the reset button, now the device should be in TFTP transfer mode. 5. Set a static IP on your Computer's NIC. A static IP of 192.168.1.25/24 should work. 6. Plug the PoE injector's LAN cable directly to your computer. 7. Start tftp client and issue following commands: tftp> binary tftp> connect 192.168.1.20 tftp> put openwrt-ath79-generic-ubnt-nano-m-xw-squashfs-factory.bin Tested-by: Joe Ayers <ae6xe@arrl.net> Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-12-12 20:09:01 +00:00
gmac-config {
device = <&gmac>;
mii-gmac0 = <1>;
mii-gmac0-slave = <1>;
};
};
Reference in New Issue Copy Permalink