ath79: add support for Qxwlan E1700AC v2
E1700AC v2 based on Qualcomm/Atheros QCA9563 + QCA9880.
Specification:
- 750/400/250 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 8/16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 3T3R 5 GHz
- 2 x 10/1000M Mbps Ethernet (RJ45)
- 1 x MiniPCI-e
- 1 x SIM (3G/4G)
- 1 x USB 2.0 Port
- 5 x LED , 2 x Button(S8-Reset Buttun), 1 x power input
- UART (J5) header on PCB (115200 8N1)
Flash instruction:
1.Using tftp mode with UART connection and original LEDE image
- Configure PC with static IP 192.168.1.10 and tftp server.
- Rename "openwrt-ar71xx-generic-xxx-squashfs-sysupgrade.bin"
to "firmware.bin" and place it in tftp server directory.
- Connect PC with one of LAN ports, power up the router and press
key "Enter" to access U-Boot CLI.
- Use the following commands to update the device to LEDE:
run lfw
- After that the device will reboot and boot to LEDE.
- Wait until all LEDs stops flashing and use the router.
2.Using httpd mode with Web UI connection and original LEDE image
- Configure PC with static IP 192.168.1.xxx(2-255) and tftp server.
- Connect PC with one of LAN ports,press the reset button, power up
the router and keep button pressed for around 6-7 seconds, until
leds flashing.
- Open your browser and enter 192.168.1.1,You will see the upgrade
interface, select "openwrt-ar71xx-generic-xxx-squashfs-
sysupgrade.bin" and click the upgrade button.
- After that the device will reboot and boot to LEDE.
- Wait until all LEDs stops flashing and use the router.
Signed-off-by: 张鹏 <sd20@qxwlan.com>
[cut out of bigger patch, keep swconfig, whitespace fixes]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-10-16 10:53:51 +00:00
|
|
|
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
|
|
|
|
|
|
#include "qca956x.dtsi"
|
|
|
|
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
|
|
|
|
/ {
|
|
|
|
aliases {
|
|
|
|
label-mac-device = ð0;
|
|
|
|
led-boot = &led_system;
|
|
|
|
led-failsafe = &led_system;
|
|
|
|
led-running = &led_system;
|
|
|
|
led-upgrade = &led_system;
|
|
|
|
};
|
|
|
|
|
|
|
|
keys {
|
|
|
|
compatible = "gpio-keys";
|
|
|
|
|
|
|
|
reset {
|
|
|
|
label = "reset";
|
|
|
|
linux,code = <KEY_RESTART>;
|
|
|
|
gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
|
|
|
|
debounce-interval = <60>;
|
|
|
|
};
|
|
|
|
};
|
|
|
|
|
|
|
|
leds {
|
|
|
|
compatible = "gpio-leds";
|
|
|
|
|
|
|
|
led_system: system {
|
|
|
|
label = "green:system";
|
|
|
|
gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
|
|
|
|
default-state = "on";
|
|
|
|
};
|
|
|
|
|
|
|
|
usb {
|
|
|
|
label = "green:usb";
|
|
|
|
gpios = <&gpio 7 GPIO_ACTIVE_LOW>;
|
|
|
|
trigger-sources = <&hub_port0>;
|
|
|
|
linux,default-trigger = "usbport";
|
|
|
|
};
|
|
|
|
|
|
|
|
wlan2g {
|
|
|
|
label = "green:wlan2g";
|
|
|
|
gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
|
|
|
|
linux,default-trigger = "phy1tpt";
|
|
|
|
};
|
|
|
|
};
|
|
|
|
};
|
|
|
|
|
|
|
|
&pcie {
|
|
|
|
status = "okay";
|
|
|
|
};
|
|
|
|
|
|
|
|
&spi {
|
|
|
|
status = "okay";
|
|
|
|
|
|
|
|
flash@0 {
|
|
|
|
compatible = "jedec,spi-nor";
|
|
|
|
reg = <0>;
|
|
|
|
spi-max-frequency = <25000000>;
|
|
|
|
|
|
|
|
partitions: partitions {
|
|
|
|
compatible = "fixed-partitions";
|
|
|
|
#address-cells = <1>;
|
|
|
|
#size-cells = <1>;
|
|
|
|
|
|
|
|
partition@0 {
|
|
|
|
label = "u-boot";
|
|
|
|
reg = <0x000000 0x040000>;
|
|
|
|
read-only;
|
|
|
|
};
|
|
|
|
|
|
|
|
partition@40000 {
|
|
|
|
label = "u-boot-env";
|
|
|
|
reg = <0x040000 0x010000>;
|
|
|
|
read-only;
|
|
|
|
};
|
|
|
|
|
|
|
|
pridata: partition@50000 {
|
|
|
|
label = "pri-data";
|
|
|
|
reg = <0x050000 0x010000>;
|
|
|
|
read-only;
|
|
|
|
};
|
|
|
|
|
|
|
|
art: partition@60000 {
|
|
|
|
label = "art";
|
|
|
|
reg = <0x060000 0x010000>;
|
|
|
|
read-only;
|
|
|
|
};
|
|
|
|
};
|
|
|
|
};
|
|
|
|
};
|
|
|
|
|
|
|
|
&mdio0 {
|
|
|
|
status = "okay";
|
|
|
|
|
|
|
|
phy0: ethernet-phy@0 {
|
|
|
|
reg = <0>;
|
|
|
|
phy-mode = "sgmii";
|
|
|
|
qca,mib-poll-interval = <500>;
|
|
|
|
|
|
|
|
qca,ar8327-initvals = <
|
|
|
|
0x04 0x00080080 /* PORT0 PAD MODE CTRL */
|
|
|
|
0x7c 0x0000007e /* PORT0_STATUS */
|
|
|
|
>;
|
|
|
|
};
|
|
|
|
};
|
|
|
|
|
|
|
|
ð0 {
|
|
|
|
status = "okay";
|
|
|
|
|
|
|
|
pll-data = <0x03000101 0x00000101 0x00001919>;
|
|
|
|
|
|
|
|
phy-mode = "sgmii";
|
|
|
|
phy-handle = <&phy0>;
|
|
|
|
|
2021-04-02 21:47:31 +00:00
|
|
|
nvmem-cells = <&macaddr_pridata_400>;
|
|
|
|
nvmem-cell-names = "mac-address";
|
ath79: add support for Qxwlan E1700AC v2
E1700AC v2 based on Qualcomm/Atheros QCA9563 + QCA9880.
Specification:
- 750/400/250 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 8/16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 3T3R 5 GHz
- 2 x 10/1000M Mbps Ethernet (RJ45)
- 1 x MiniPCI-e
- 1 x SIM (3G/4G)
- 1 x USB 2.0 Port
- 5 x LED , 2 x Button(S8-Reset Buttun), 1 x power input
- UART (J5) header on PCB (115200 8N1)
Flash instruction:
1.Using tftp mode with UART connection and original LEDE image
- Configure PC with static IP 192.168.1.10 and tftp server.
- Rename "openwrt-ar71xx-generic-xxx-squashfs-sysupgrade.bin"
to "firmware.bin" and place it in tftp server directory.
- Connect PC with one of LAN ports, power up the router and press
key "Enter" to access U-Boot CLI.
- Use the following commands to update the device to LEDE:
run lfw
- After that the device will reboot and boot to LEDE.
- Wait until all LEDs stops flashing and use the router.
2.Using httpd mode with Web UI connection and original LEDE image
- Configure PC with static IP 192.168.1.xxx(2-255) and tftp server.
- Connect PC with one of LAN ports,press the reset button, power up
the router and keep button pressed for around 6-7 seconds, until
leds flashing.
- Open your browser and enter 192.168.1.1,You will see the upgrade
interface, select "openwrt-ar71xx-generic-xxx-squashfs-
sysupgrade.bin" and click the upgrade button.
- After that the device will reboot and boot to LEDE.
- Wait until all LEDs stops flashing and use the router.
Signed-off-by: 张鹏 <sd20@qxwlan.com>
[cut out of bigger patch, keep swconfig, whitespace fixes]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-10-16 10:53:51 +00:00
|
|
|
};
|
|
|
|
|
|
|
|
&usb_phy0 {
|
|
|
|
status = "okay";
|
|
|
|
};
|
|
|
|
|
|
|
|
&usb0 {
|
|
|
|
#address-cells = <1>;
|
|
|
|
#size-cells = <0>;
|
|
|
|
status = "okay";
|
|
|
|
|
|
|
|
hub_port0: port@1 {
|
|
|
|
reg = <1>;
|
|
|
|
#trigger-source-cells = <0>;
|
|
|
|
};
|
|
|
|
};
|
|
|
|
|
|
|
|
&usb_phy1 {
|
|
|
|
status = "okay";
|
|
|
|
};
|
|
|
|
|
|
|
|
&usb1 {
|
|
|
|
status = "okay";
|
|
|
|
};
|
|
|
|
|
|
|
|
&wmac {
|
|
|
|
status = "okay";
|
|
|
|
|
|
|
|
mtd-cal-data = <&art 0x1000>;
|
|
|
|
};
|
2021-04-02 21:47:31 +00:00
|
|
|
|
|
|
|
&pridata {
|
|
|
|
compatible = "nvmem-cells";
|
|
|
|
#address-cells = <1>;
|
|
|
|
#size-cells = <1>;
|
|
|
|
|
|
|
|
macaddr_pridata_400: macaddr@400 {
|
|
|
|
reg = <0x400 0x6>;
|
|
|
|
};
|
|
|
|
};
|