The Librem Key is a custom device USB-based security token Nitrokey is
producing for Purism and among other things it has custom firmware
created for use with Heads. In particular, when a board is configured
with CONFIG_LIBREMKEY, this custom firmware allows Heads to use the
sealed TOTP secret to also send an HOTP authentication to the Librem
Key. If the HOTP code is successful, the Librem Key will blink a green
LED, if unsuccessful it will blink red, thereby informing the user that
Heads has been tampered with without requiring them to use a phone to
validate the TOTP secret.
Heads will still use and show the TOTP secret, in case the user wants to
validate both codes (in case the Librem Key was lost or is no longer
trusted). It will also show the result of the HOTP verification (but not
the code itself), even though the user should trust only what the Librem
Key displays, so the user can confirm that both the device and Heads are
in sync. If HOTP is enabled, Heads will maintain a new TPM counter
separate from the Heads TPM counter that will increment each time HOTP
codes are checked.
This change also modifies the routines that update TOTP so that if
the Librem Key executables are present it will also update HOTP codes
and synchronize them with a Librem Key.
Currently the TPM counter label is hard-coded. By changing it to a
variable in this function we can reuse all of the TPM counter functions
to create other monotonic counters in the TPM (if the hardware supports
it) with custom labels.
There was a bug in the "force" boot mode where it would still fail if
signatures didn't match. This was because the check_config function
validates the signatures for kexec files. I've added a few conditionals
here so that in the case of a forced boot mode, we can bypass those
signature checks that would prevent boot and error out to a recovery
console.
Guarded linuxboot specific init entries
Removed Makefile entries into separate file (conflicts with srcing /etc/config)
Added CONFIG_BOOT_LOCAL/_REMOTE to control interface setup
Fixed CONFIG_TPM usage
if "CONFIG_TPM=y" is not present in the config file, functionalities
needing TPM could be disabled, while leaving other functionalities intact.
This will make Heads a more general-usage bootloader payload atop coreboot.
USB smart card readers are most full speed devices, and there is no
"rate-matching hubs" beneath the root hub on older (e.g. GM45) plat-
forms, which has companion OHCI or UHCI controllers and needs cor-
responding drivers to communicate with card readers directly plugged
into the motherboard, otherwise a discrete USB hub should be inserted
between the motherboard and the reader.
This time I make inserting linux modules for OHCI and UHCI controllable
with option CONFIG_LINUX_USB_COMPANION_CONTROLLER.
A linux config for x200 is added as an example.
Tested on my x200s and elitebook revolve 810g1.
if "CONFIG_TPM=y" is not present in the config file, functionalities
needing TPM could be disabled, while leaving other functionalities intact.
This will make Heads a more general-usage bootloader payload atop coreboot.
This development branch builds a NERF firmware for the Dell R630
server. It does not use coreboot; instead it branches directly
from the vendor's PEI core into Linux and the Heads runtime
that is setup to be run as an EFI executable.
Changed the checking of required hashes or required rollback state
to be right before boot, allowing the user to sign/set defaults
in interactive mode.
Also cleaned up usages of recovery and fixed iso parameter
regression.
Similar to qubes-update, it will save then verify the hashes of
the kexec files. Once TOTP is verified, a normal boot will verify
that the file hashes and all the kexec params match and if
successful, boot directly to OS.
Also added a config option to require hash verification for
non-recovery boots, failing to recovery not met.
Supports booting from USB media using either the root device or
a signed ISO as the boot device. Boot options are parsed with
quick/dirty shell scripts to infer kexec params.
Closes#195 and begins to address #196
This addresses multiple issues:
* Issue #63: initrd is build fresh each time, so tracked files do not matter.
* Issue #144: build time configuration
* Issue #123: allows us to customize the startup experience
* Issue #122: manual start-xen will go away
* Issue #25: tpmtotp PCRs are updated after reading the secret
* Issue #16: insmod now meaures modules
Reduce the size of flashrom by commenting out most flash chips,
boards and programmers.
Wrapper script to make it easier to rewrite the ROM on the x230
using the flashrom layout.
Keep the entire 12 MB ROM for flashing.
