Point stack to client context region and save registers using push
instructions.
Note that since the push instruction first increments the stack pointer
and then stores the value on the stack, the RSP has to point one field
past RBP before pushing the first register value.
As the kernel entry is called from the interrupt handler the stack
layout is as specified by Intel SDM Vol. 3A, figure 6-8. An additional
vector number is stored at the top of the stack.
Gather the necessary client information from the interrupt stack frame
and store it in the client context.
The new errcode field is used to store the error code that some
interrupts provide (e.g. #PF). Rework mode transition reserved space and
offset constants to match the new CPU_state layout.
The macros are used to assign syscall arguments to specific registers.
Using the AMD64 parameter passing convention avoids additional copying of
variables since the C++ function parameters are already in the right
registers.
The interrupt return instruction in IA-32e mode applies the prepared
interrupt stack frame to set the RFLAGS, CS and SS segment as well as
the RIP and RSP registers. It then continues execution of the user code.
For detailed information refer to Intel SDM Vol. 3A, section 6.14.3.
After activating the client page tables the client context cannot be
accessed any longer. The mode transition buffer however is globally
mapped and can be used to restore the remaining register values.
Set the stack pointer to the R8 field in the client context to enable
restoring registers by popping values of the stack.
After this step the only remaining registers that do not contain client
values are RAX, RSP and RIP.
Note that the client value of RAX is pop'd to the global buffer region as
the register will still be used by subsequent steps. It will be restored to
the value in the buffer area just prior to resuming client code execution.
Set I/O privilege level to 3 to allow core to perform port I/O from
userspace. Also make sure the IF flag is cleared for now until interrupt
handling is implemented.
Setup an IA-32e interrupt stack frame in the mode transition buffer region.
It will be used to perform the mode switch to userspace using the iret
instruction.
For detailed information about the IA-32e interrupt stack frame refer to
Intel SDM Vol. 3A, figure 6-8.
The constants specify offset values of CPU context member variables as
specified by Genode::Cpu_state [1] and Genode::Cpu::Context [2].
[1] - repos/base/include/x86_64/cpu/cpu_state.h
[2] - repos/base-hw/src/core/include/spec/x86/cpu.h
The new entries specify a 64-bit code segment with DPL 3 at index 3 and a
64-bit data segment with DPL 3 at index 4.
These segments are needed for transitioning to user mode.
A pointer to the client context is placed in the mt_client_context_ptr area.
It is used to pass the current client context to the lowlevel mode-switching
assembly code.
IA-32e paging translates 48-bit linear addresses to 52-bit physical
addresses. Translation structures are hierarchical and four levels deep.
The current implementation supports regular 4KB and 1 GB and 2 MB large
page mappings.
Memory typing is not yet implemented since the encoded type bits depend
on the active page attribute table (PAT)*.
For detailed information refer to Intel SDM Vol. 3A, section 4.5.
* The default PAT after power up does not allow the encoding of the
write-combining memory type, see Intel SDM Vol. 3A, section 11.12.4.
* Add common IA-32e paging descriptor type:
The type represents a table entry and encompasses all fields shared by
paging structure entries of all four levels (PML4, PDPT, PD and PT).
* Simplify PT entry type by using common descriptor:
Differing fields are the physical address, the global flag and the memory
type flags.
* Simplify directory entry type by using common descriptor:
Page directory entries (PDPT and PD) have an additional 'page size' field
that specifies if the entry references a next level paging structure or
represents a large page mapping.
* Simplify PML4 entry type by using common descriptor
Top-level paging structure entries (PML4) do not have a 'pat' flag and the
memory type is specified by the 'pwt' and 'pcd' fields only.
* Implement access right merging for directory paging entries
The access rights for translations are determined by the U/S, R/W and XD
flags. Paging structure entries that reference other tables must provide
the superset of rights required for all entries of the referenced table.
Thus merge access rights of new mappings into existing directory entries to
grant additional rights if needed.
* Add cr3 register definition:
The control register 3 is used to set the current page-directory base
register.
* Add cr3 variable to x86_64 Cpu Context
The variable designates the address of the top-level paging structure.
* Return current cr3 value as translation table base
* Set context cr3 value on translation table assignment
* Implement switch to virtual mode in kernel
Activate translation table in init_virt_kernel function by updating the
cr3 register.
* Ignore accessed and dirty flags when comparing existing table entries
These flags can be set by the MMU and must be disregarded.
* Add isr.s assembler file:
The file declares an array of Interrupt Service Routines (ISR) to handle
the exception vectors from 0 to 19, see Intel SDM Vol. 3A, section
6.3.1.
* Add Idt class:
* The class Genode::Idt represents an Interrupt Descriptor Table as
specified by Intel SDM Vol. 3A, section 6.10.
* The setup function initializes the IDT with 20 entries using the ISR
array defined in the isr.s assembly file.
* Setup and load IDT in Genode::Cpu ctor:
The Idt::setup function is only executed once on the BSP.
* Declare ISRs for interrupts 20-255
* Set IDT size to 256
This patch contains the initial code needed to build and bootstrap the
base-hw kernel on x86 64-bit platforms. It gets stuck earlier
because the binary contains 64-bit instructions, but it is started in
32-bit mode. The initial setup of page tables and switch to long mode is
still missing from the crt0 code.
To ease debugging without the need to tweak the kernel every time, and to
support userland developers with useful information this commit extends several
warnings and errors printed by the kernel/core by which thread/application
caused the problem, and what exactly failed.
Fix#1382Fix#1406
In the past, unmap sometimes occured on RM clients that have no thread,
PD, or translation table assigned. However, this shouldn't be the
case anymore.
Fixes#504
* Introduce hw-specific crt0 for core that calls e.g.: init_main_thread
* re-map core's main thread UTCB to fit the right context area location
* switch core's main thread's stack to fit the right context area location
Fix#1440
This decouples the size of the mode transition control region from the
minimal mapping size of the page tables implementation. Rather, the CPU
architecture is able to specify the actual size.
Rationale: For x86_64, we need the mtc region to span two pages in order
to store all the tables required to perform the mode switch.
For the USB-Armory, we use a newer version of Linux (3.18) as for the
i.MX53-QSB. The main difference is, that the newer Linux uses a DTB instead of
ATAGs.
Fixes#1422
The USB Armory is almost the same as the i.MX53-QSB but it uses only
one of the two RAM banks available in i.MX53. Furthermore we use the USB
Armory only with Trustzone enabled.
Ref #1422
* enables world-switch using ARM virtualization extensions
* split TrustZone and virtualization extensions hardly from platforms,
where it is not used
* extend 'Vm_session' interface to enable configuration of guest-physical memory
* introduce VM destruction syscall
* add virtual machine monitor for hw_arndale that emulates a simplified version
of ARM's Versatile Express Cortex A15 board for a Linux guest OS
Fixes#1405
To enable support of hardware virtualization for ARM on the Arndale board,
the cpu needs to be prepared to enter the non-secure mode, as long as it does
not already run in it. Therefore, especially the interrupt controller and
some TrustZone specific system registers need to be prepared. Moreover,
the exception vector for the hypervisor needs to be set up properly, before
booting normally in the supervisor mode of the non-secure world.
Ref #1405
The generalization of interrupt objects in the kernel and the use of
C++ polymorphism instead of explicitely checking for special interrupts
within generic code (Cpu_job::_interrupt) enables the registration of
additional interrupts used by the kernel, which are needed for specific
aspects added to the kernel, like ARM hardware virtualization interrupts.
* Introduce generic base class for interrupt objects handled by the kernel
* Derive an interrupt class for those handled by the user-land
* Implement IPI-specific interrupt class
* Implement timer interrupts using the new generic base class
Ref #1405
Until now, one distinct software generated IRQ per cpu was used to
send signals between cpus. As ARM's GIC has 16 software generated
IRQs only, and they need to be partitioned between secure/non-secure
TrustZone world as well as virtual and non-virtual worlds, we should
save them.
Ref #1405
* name irq controller memory mapped I/O regions consistently
in board descriptions
* move irq controller and timer memory mapped I/O region descriptions
from cpu class to board class
* eliminate artificial distinction between flavors of ARM's GIC
* factor cpu local initialization out of ARM's GIC interface description,
which is needed if the GIC is initialized differently e.g. for TrustZone
Ref #1405
