If 'system="yes"' is specified in the <config>, the platform driver now
monitors the content of the system ROM. Should the value become "reset",
a reset is triggered using information obtained from the ACPI driver.
Related to issue #2726
The change of the platform driver is needed to avoid a parsing error of
the ACPI ROM when encountering an unexpected <reset> node.
Thanks to Alexander Boettcher for the preventing the regression of #3829
and improving the adherence to the ACPI spec when parsing the reset type.
Related to issue #2726
* Remove SPEC declarations from mk/spec
* Remove all board-specific REQUIRE declaratiions left
* Replace [have_spec <board>] run-script declarations with have_board where necessary
* Remove addition of BOARD variable to SPECS in toplevel Makefile
* Move board-specific directories in base-hw out of specs
In order to perform a smooth transition from NIC drivers that act only as NIC
session clients to NIC drivers that act only as Uplink session clients, this
commit introduces an intermediate state in which all NIC drivers support both
modes. That said, a NIC drivers mode is now statically determined through a new
optional 'mode' attribute in the drivers <config> tag that can be set to either
'nic_server' (default value) or 'uplink_client'. Reconfiguring this attribute
at a driver doesn't have any effects. Whithout this attribute being set, all
NIC drivers will behave the same as they did before the commit. When set to
'uplink_client', however, instead of providing a Nic service, they request
an Uplink session whenever their network interface becomes "UP" and close the
session whenever their network interface becomes "DOWN".
Ref #3961
- depending on available PCI power cap power off and on
- save and restore PCI bars if required
- reset PCI devices after power on if supported
Fixes#3963
using Register_set && Register. It is derived from Genode::Mmio, however uses
as backend the Config_access implementation which is still used widely in
the platform driver.
Issue #3963
Replace explicit usage of bus, device, function arguments to methods or
variables all over the code by a single data type. It eases the reading of and
shorten the code.
Issue #3963
The driver is faily simple and does not support fancy features like
TCP checksum offloading or vlan filtering, but it is fully capable of
running every Genode network based scenario I've tried. Its currently
known to work on virt_qemu arm platforms and x86_64.
Fix#3825
The VirtIO device configuration on Qemu is dynamic. The
order and presence of different command line switches affects
base address and interrupt assignment of each device. One could
probably hard-code the necessary switches and resulting XML ARM
platform driver configuration in each run script, but this seems
like troublesome and hard to maintain solution.
This patch explores an alternative approach to the problem.
It implements a ROM driver which probes the address space region
Qemu virt machines assign to VirtIO MMIO devices and exposes the
result as XML via a ROM session. This XML output can be fed directly
as config to the generic ARM platform driver.
Ref #3825
- make GPIO server more robust on imx by not throwing exceptions for
unknown pins, use '_with_gpio' instead
- use 'Gpio::Pin' data type instead of POD 'unsigned'
issue #3900
The patch handles the case, that the memory for the MSI-X table is part
of one of the Pci::Resource Memory BARs, which got allocated beforehand already.
With this commit, the platform driver will not fall back to use legacy IRQs or MSI, whereby MSI-X is available actually. Additionally, this patch avoids a lot of red
messages about non available IO-MEM printed by the roottask.
Fixes#3904
The combination of Net::Mac_address and
Genode::ascii_to(Net::Mac_address) required shaky quirks in several
places because GCC is not able to resolve the ascii_to overload if
base/xml_node.h was included to early. The current solution moves the
several ascii_to overloads "closer" to the Net types by putting them
into the Net namespace, where GCC reliably picks them up.
Hence, co-locating the ascii_to() utility with the overload type in the
same scope/namespace is good practice.
This patch removes the now obsolete <nic/xml_node.h> header file.
* Fixes faulty algorithm in fractional pll rate calculation
* Enables clocks that are set as reference clock to prevent system freeze
* Enables/disables root clocks of gates implicitely
Fix#3876
By now, the enumeration of peripheral interrupts on Raspberry Pi 1 was
different in between base-hw kernel and Fiasco.OC. Therefore, hacks were
needed in every driver to request the correct interrupt number dependent
on the kernel. Before reproducing the same in the platform driver for rpi,
we can more easily use the same enumeration with base-hw.
Ref #3864
This is a temporary workaround to not harm drivers, which aren't
converted yet to request all device resources including power and
clocks from this new platform driver.
Ref #3863
Introduce the managing_system privilege for components like the
platform_driver to allow it to call system management functionality
that is reserved by kernel or special firmware, e.g., ARM Trusted Firmware.
The former RAM resource configuration attribute `constrain_phys`,
which enabled to constrain the region of physical RAM to be used,
gets replaced by the new, broader managing_system configuration
attribute of a `start` node. It gets enforced by the sandbox library.
Ref #3816
The driver wrongly rejected a block request for the very last block of
the device, which prevented part_block from successfully parsing the
partition table (when attempting to access the GPT backup).
Fixes#3861
