for such classes where it should be safe and where we have seen issues.
Disabling in general bus master DMA causes on some machines hard hangs, e.g.
because the USB handover protocol was violated.
Fixes#2835
This commit changes the 'Input::Event' type to be more safe and to
deliver symbolic character information along with press events.
Issue #2761Fixes#2786
When working with GPIO interrupts on i.MX6SX for Ethernet PHYs
it became obvious that the GPIO driver repeatedly receives interrupts
for the same event, because it acknowledges the interrupt before a
client has handled the event.
Ref #2750
This driver component provides support for using consumer NVMe storage
devices, i.e. it omits name space managment and will always use the
first name space, on Genode. For now it defaults to a reasonable low
configuration:
- 1 I/O queue (completion/submission tuple)
- 128 entries in the I/O queue
- 4096 as the only I/O transaction memory page size
Fixes#2747.
Relative motion events with a motion vector of (0,0) should not exists.
They cause jittery movements of nitpicker's pointer position. This
patch filters out such events.
Switch port I/O based PCI config space access to memory-mapped IO. The
base address of the PCI configuration space is acquired by mapping the
ACPI ROM and reading the first <bdf> node. An exception is thrown if the
first <bdf> node is not for PCI domain zero or if multiple <bdf> nodes
exist. This is to reduce complexity and also because multiple PCI
domains are rare.
The PCI configuration space is accessed via I/O mem dataspace which is
created in the platform_drv root and then passed on to the PCI session,
device components and finally to the actual PCI config access instances.
The memory access code is implemented in a way to make it work with Muen
subject monitor (SM) device emulation and also general x86 targets. On
Muen, the simplified device emulation code (which works also for Linux)
always returns 0xffff in EAX to indicate a non-existing device.
Therefore, EAX is enforced in the assembly templates.
Fixes#2547
The new 'Terminal_session::size_changed_sigh' RPC function registers a
signal handler that is triggered each time when the terminal size
changes. It enables the client to adjust itself to the new size by
subsequently calling the 'size' RPC function. Of all terminal servers,
only the graphical terminal triggers this signal.
Require x86_64 because memory/adress space limitations on x86_32
restrict the use-cases on such a platform anyway. Doing that,
we can also assume that memory adresses are always 64bit long and
do not have to handle 32bit adresses.
The patch adjust the code of the base, base-<kernel>, and os repository.
To adapt existing components to fix violations of the best practices
suggested by "Effective C++" as reported by the -Weffc++ compiler
argument. The changes follow the patterns outlined below:
* A class with virtual functions can no longer publicly inherit base
classed without a vtable. The inherited object may either be moved
to a member variable, or inherited privately. The latter would be
used for classes that inherit 'List::Element' or 'Avl_node'. In order
to enable the 'List' and 'Avl_tree' to access the meta data, the
'List' must become a friend.
* Instead of adding a virtual destructor to abstract base classes,
we inherit the new 'Interface' class, which contains a virtual
destructor. This way, single-line abstract base classes can stay
as compact as they are now. The 'Interface' utility resides in
base/include/util/interface.h.
* With the new warnings enabled, all member variables must be explicitly
initialized. Basic types may be initialized with '='. All other types
are initialized with braces '{ ... }' or as class initializers. If
basic types and non-basic types appear in a row, it is nice to only
use the brace syntax (also for basic types) and align the braces.
* If a class contains pointers as members, it must now also provide a
copy constructor and assignment operator. In the most cases, one
would make them private, effectively disallowing the objects to be
copied. Unfortunately, this warning cannot be fixed be inheriting
our existing 'Noncopyable' class (the compiler fails to detect that
the inheriting class cannot be copied and still gives the error).
For now, we have to manually add declarations for both the copy
constructor and assignment operator as private class members. Those
declarations should be prepended with a comment like this:
/*
* Noncopyable
*/
Thread(Thread const &);
Thread &operator = (Thread const &);
In the future, we should revisit these places and try to replace
the pointers with references. In the presence of at least one
reference member, the compiler would no longer implicitly generate
a copy constructor. So we could remove the manual declaration.
Issue #465
Multi-wraps
-----------
Previously, on every new timeout, we programmed registers LR=timeout and
CMP=0. The counter than counted from LR down to 0, triggered the IRQ,
jumped back to LR, and counted down again. If one installed small
timeouts (< 1000 us), it was likely that the counter wrapped multiple
times before we were able to read it out. Initially, this was not a big
issue as the additional wraps were simply ignored and the amount of time
lost through this was not big. But when we want to do correct rate
limitation, multiple wraps cause an overflow in the additional
calculations, and this has a big effect on the resulting time value.
Thus, we now program the counter to start from ~0 and count down to 0.
We set CMP=~0-timeout so that the timer still triggers the IRQ at the right
time. The counter continues counting down after the IRQ has triggered until
we install a new timeout. We do not consider anymore that the counter wraps.
The maximum timeout is set to half the maximum counter value, so, we should
be able to install a new timeout before the counter wraps.
Rate limit for time updates
---------------------------
In the time span between two interrupts we have to remember how many ticks
we have already added to the time value. This is because at each call of
curr_time we can only see how many ticks have passed since the last call of
schedule_timeout and not since the last call of curr_time. But we want to
limit the rate of time updates in curr_time. With the member for ticks that
were already added since the last call to schedule_timeout we can then
calculate how many are yet to be added.
Ensure that the timer does not handle timeouts again within 1000
microseconds after the last handling of timeouts. This makes denial of
service attacks harder. This commit does not limit the rate of timeout
signals handled inside the timer but it causes the timer to do it less
often. If a client continuously installs a very small timeout at the
timer it still causes a signal to be submitted to the timer each time
and some extra CPU time to be spent in the internal handling method. But
only every 1000 microseconds this internal handling causes user timeouts
to trigger.
If we would want to limit also the call of the internal handling method
to ensure that CPU time is spent beside the RPCs only every 1000
microseconds, things would get more complex. For instance, on NOVA
Time_source::schedule_timeout(0) must be called each time a new timeout
gets installed and becomes head of the scheduling queue. We cannot
simply overwrite the already running timeout with the new one.
Ref #2490
If the PIT timer driver gets activated too slow (e.g. because of a bad priority
configuration), it might miss counter wraps and would than produce sudden time
jumps. The driver now detects this problem dynamically, warns about it and
adapts the affected values to avoid time jumps.
Ref #2400
Add a "writeable" policy option to the ahci_drv and part_blk Block
servers and default from writeable to ready-only. Should a policy
permit write acesss the session request argument "writeable" may still
downgrade a session to ready-only.
Fix#2469
There are hardware timers whose frequency can't be expressed as
ticks-per-microsecond integer-value because only a ticks-per-millisecond
integer-value is precise enough. We don't want to use expensive
floating-point values here but nonetheless want to translate from ticks
to time with microseconds precision. Thus, we split the input in two and
translate both parts separately. This way, we can raise precision by
shifting the values to their optimal bit position. Afterwards, the results
are shifted back and merged together again.
As this algorithm is not so trivial anymore and used by at least three
timer drivers (base-hw/x86_64, base-hw/cortex_a9, timer/pit), move it to a
generic header to avoid redundancy.
Ref #2400
