The wifi VFS plugin is solely there to provide a hook for calling
'Lx_kit::initialize()' prior to the static ctors. As the corresponding
symbol can be resolved at run-time there is no need to add the
library as a build-time dependency.
Issue #4813
The device-tree binary is normally required on ARM-based platforms
where as on x86 it is omitted. The platform-specific DTB helper
provides a generic interface for accssing the DTB and needs to be
implemented on each platform.
Issue #4813
The SDIO connected wireless device on the PinePhone is not available
on start-up, which leads to the supplicant failing to initalize
'wlan0'. Normally the supplicant would be used in a way that handling
devices that appear at run-time happens gracefully.
Rather than supporting this behavior we defer the start-up of the
supplicant until the device could be openend successfully for now.
Issue #4813
The MAC address device report should be published once the device is
available. Since this may happen at a later time we have to check the
call.
Issue #4813
This commit introduces support for building the WLAN driver for ARM
platforms. It makes the WPA supplicant and its support libraries
available for all platforms. It also seperates the PCI parts to
accommodate platforms where other bus protocols are used.
Issue #4813
The driver was only tested with an "Atheros AR9462 Rev:2" [168c:0034]
device using the 'wifi.run' run script.
Note: for it to work MSI may not be used as otherwise interrupts do not
work. Using an IOMMU leads to the following fault:
[ 0] IOMMU:0xffffffff817eb0b0 FRR:0 FR:0x22 BDF:4:0:0 FI:0xb0000000000000 (0)
Issue #4813
This commit updates the used firmware images for the iwlwifi device
to latest available ones (supported by the current 6.1.x driver).
It also removes old firmware images that by now are not used anymore.
Fixes#4807.
Implement udelay for all architectures within common lx_emul code,
remove driver-specific version.
Always do busy looping in udelay and use cpu_relax()
like the original Linux code. Thereby, we profit from architecture specific
instructions (cpu cool down), and jiffies are updated if irqs are on.
Ref genodelabs/genode#4778
There are rare use-cases where cpu_relax is used inside a busy loop
(i2c bus functions), which only will break when the jiffies counter
reaches a specific value.
Because of the cooperative scheduling done in lx_emul, no timer
interrupt will break such a loop. As a workaround, we check for
necessary jiffies updates inside cpu_relax if interrupts are enabled.
Ref genodelabs/genode#4778
Due to lacking hardware access the driver was test with one RTL8188EE
based device, namely [10ec:8179] (rev 01), only. As the access to the
PCI config space is restricted the driver loads the non power-saving
FW and the driver port is therefor only tested with that. The
accesses are documented should we choose to support them one way or
another later on.
The 'wifi.run' run script as well as Sculpt served as testing ground
where the driver worked fine so far.
Fixes#4714.
Genode build system allows to easily enable 'ccache' for builds. This
change allows to enable using 'ccache' also for build of reference
Linux kernel used during porting device drivers.
To enable 'ccache' it is enough to pass value of 'CC' variable when
executing Linux build but this build by default depends on time when it
is built which causes 'ccache' misses. To solve this issue additional
flags are passed to make build independent from time, current user and
host on which build is performed.
Issue #4718
In case of very rapid config ROM change (<300ms), the linux driver may still
be in progress of applying the previous change (e.g. switching connector on/off).
During this progress all tasks may become not runnable (waiting for IRQ/timeouts
until hardware state settles), the newest config ROM change/signal gets
dispatched, which lead to continuing the previous change request, but not
to re-starting/re-applying the new config change. To avoid this situation,
explicitly track whether a previous config change was finished and track if an
interim config change request came in. If so, re-start the lx_user
task with the newest config change.
Fixes#4721
Although we do not have the full ACPI information parsed yet, to
announce non-PCI devices derived from the ACPI tables, the device
description of the assumed devices is now integral-part of pci_decode.
Formerly, the information was gained separatedly as boot-module, whereby
we lost synchronization in between ACPI/PCI parsing, BIOS handover, and
PS/2 emulation code already acting.
Until now, requesting optional blobs such as 'iwl-debug-yoyo.bin' has
just failed silently. To support desired blobs such as PNVM firmware,
implement the loading of optional firmware while preserving the nowarn
characteristics of the function.
Issue #4663
In case the allocation fails for the largest possible connector mode,
try smaller modes. Additional add option to specify maximal resolution.
Issue #4659
