Replace the unconditional sleep "until the board comes up" by the
detection of the fastboot-driver message. This shortens the total boot
time and reveals U-boots initial output, e.g., messages reporting
trouble with bringing up the fastboot driver.
The success messages of different versions of the fastboot tool
are printed in different upper/lower case. Tolerate both.
The patch also removes a few superfluous semicolons.
This disambiguates the boot images installed for base-hw from those
installed for base-nova.
Note that the image.elf file for other kernels (i.e., NOVA) is not
named image-<kernel>.elf at this point because this would prevent the
update from a pre-24.04 Sculpt system to a later one as the grub.cfg
is not touched by the old update mechanism. So after a system update,
grub would keep loading the last installed image.elf.
Issue #5182
An installed lighttpd HTTP server can now optionally be started to serve
the boot image with the follow run options.
--load-ipxe-lighttpd run lighttpd automatically (default: off)
--load-ipxe-lighttpd-port <port> TCP port to run lighttpd on (default: 8080)
This patch lifts the limitation for 32-bit ARM platforms and makes the
parameter --load-fastboot-device optional. If only one device is
present, it can be omitted.
Fixes#4232
The install_pxe_bootloader_to_run_dir procedure is required by the tftp
as well as the ipxe load script. Move it to a separate file which is
include by both.
'unzip' can uncompress and load raw multiboot images and ELF files.
Usage together with the PXE bootloader ease life running the muen hypervisor
together with a Genode/x86_64 VM, where the raw boot image is typically quite
large.
Ref #2358
This makes use of the iPXE sanboot command [1] which downloads and
boots an ISO image directly via HTTP. Therefore, your RUN_OPT needs
both
--include image/iso and
--include load/ipxe
NOTE: The webserver serving the ISO image must support ranged requests,
see [2].
[1] - http://ipxe.org/cmd/sanboot
[2] - http://forum.ipxe.org/showthread.php?tid=7295&pid=10482#pid10482
iPXE is an open source network boot firmware which supports booting from
a web server via HTTP [1].
The following two parameters can be used to specify the iPXE/HTTP setup:
--load-ipxe-base-dir
This parameter specifies the base directory of the HTTP server from
which the target machine downloads the files.
--load-ipxe-boot-dir
The directory relative to iPXE base dir which contains the iPXE
chainload configuration and all necessary files.
The target machine is expected to request the following iPXE
configuration via HTTP:
http://${HOST_URL}/${ipxe-boot-dir}/boot.cfg
This can be achieved by building iPXE with the following embedded
script:
#!ipxe
dhcp
chain http://${HOST_URL}/${ipxe-boot-dir}/boot.cfg
See also [2] for additional information.
[1] - http://ipxe.org/
[2] - http://ipxe.org/howto/chainloading#breaking_the_loop_with_an_embedded_scriptFixes#1708
If a user has e.g. /tftpboot/x86 as directory and configures
base_dir=/tftboot and offset_dir=/x86, this leads to bad behavior
as the load module creates a symlink
/tftpboot/x86/<builddir> -> <absolut_builddir>
in this case instead of the desired
/tftpboot/x86 -> <absolut_builddir>
Furthermore, the module works on
/tftpboot/x86/config-00-00-00-00-00-00
and
/tftpboot/x86/<builddir>/config-00-00-00-00-00-00
afterwards, which looks bad too. As there is no warning at all, this can
be hard to debug. The commit adds an appropriate check with error message and
exit -1 on an existing directory.
Fixes#1630
