... and then use the right option. See the note in scripts/functions
on where we should use ${foo} and where just 'foo'; this boils down to
whether we can expect the build tools override to be in effect (e.g. in
the actual build scripts) or not (i.e. outside of scripts/build).
While running in scripts/functions, or in scripts/crosstool-NG.sh the
build tools override directory (.build/tools/bin) may have not been
set up (yet, or at all).
Also, modify the installed scripts (populate, xldd) accordingly.
Signed-off-by: Alexey Neyman <stilor@att.net>
... it is not needed to install headers and causes build failures
in more than one setup (cygwin, macos).
Signed-off-by: Alexey Neyman <stilor@att.net>
The referenced commit replaced 'make' with '${make}' everywhere. This is
wrong for at least the utilities that we may build as companion tools
(make, libtool): this will always invoke the version detected by configure
by supplying the absolute path. In other words, the wrappers in
.build/tools/bin are not fallbacks - they are either temporary (in case
a respective companion tool is built) or permanent redirectors.
This is the reason why the PATH= has .build/*/buildtools/bin at higher
precedence than .build/tools/bin; the latter has the versions detected by
configure and the former has the versions built as companion tools.
Revert the rest of the gang (grep/sed/...) for consistency. After all,
we may decide to supply some of them as well (awk, for instance).
Signed-off-by: Alexey Neyman <stilor@att.net>
This commit updates the build scripts to match the new usage of
CT_GetCustom from the previous change.
Signed-off-by: Bryan Hundven <bryanhundven@gmail.com>
This option allowed you to use a custom headers directory/tarball to use
in your sysroot.
Not to be confused with using a custom source, that option is the
preferred method.
Signed-off-by: Bryan Hundven <bryanhundven@gmail.com>
Reviewed-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
We check for apps:
* make
* sed
* grep
* awk
* libtool/libtoolize
* install
* patch
* and more
...during configure. Our scripts should be consistent about using the
variables that define where the found tool was found.
Of course, we do hard-link these tools in buildtools, but that should be
a backup for the components we are building. Our scripts should always
use the tools we find.
Signed-off-by: Bryan Hundven <bryanhundven@gmail.com>
This commit removes blackfin support.
I'm open to re-adding blackfin after crosstool-1.23.0 is released, but
it is currently too difficult to port forward to newer versions of gcc
and uclibc.
Signed-off-by: Bryan Hundven <bryanhundven@gmail.com>
Some architectures, like arc and blackfin set CROSS_COMPILE to a default
if it is not set on the command-line.
Since we are building the cross-compiler, we need to ALWAYS set
CROSS_COMPILE, since building/checking headers is done after the GCC
PASS1 step.
Signed-off-by: Bryan Hundven <bryanhundven@gmail.com>
This change updates the download locations to default to the official
download site.
For gcc and gdb, also separate out the linaro download locations so that
if you are downloading the linaro variant, it skips trying to download
from the official gcc mirror.
This commit closes#3
Signed-off-by: Bryan Hundven <bryanhundven@gmail.com>
Reported-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cset 3b61be3d7aa6 (prepare for arch whose kenel name is not the standard name)
failed to name a variable consistently, so all archs but arm64 were broken.
Fix that by renaming the variable in a consistent way.
Reported-by: Maxime Hadjinlian <maxime.hadjinlian@gmail.com>
Signed-off-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
AArch64 id the 64-bit variant for ARM.
Signed-off-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Cc: Zhenqiang Chen <zhenqiang.chen@linaro.org>
Cc: Michael Hope <michael.hope@linaro.org>
For some architectures, the kernel architecture name is not the common
name of the architecture for other tools.
For example: ARM 64-bit is commonly referenced as aarch64, but the kernel
calls it arm64.
Signed-off-by: Michael Hope <michael.hope@linaro.org>
Signed-off-by: Zhenqiang Chen <zhenqiang.chen@linaro.org>
[yann.morin.1998@free.fr: split out of the aarch64 patch]
Signed-off-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Replace the 32-bit-only mingw32 with mingw-w64 that is capable
of building toolchains for both 32-bit and 64-bit Windows.
kernel/mingw: replace mingw32 with generic Windows
kernel/windows: New windows kernel supporting 32 and 64 bit arch
libc/mingw: Remove old options
patches: Remove old mingw libc options' patches
Signed-off-by: "Yann Diorcet" <diorcet.yann@gmail.com>
[yann.morin.1998@free.fr: array var in libc/mingw.sh, typos]
Signed-off-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Message-Id: <b045ac08fc9eac2e5ee3.1352898499@blackmint>
Patchwork-Id: 198901
Currently, extract and patch are skipped as thus:
- using a custom directory of pre-installed headers
- a correctly named directory already exists
Otherwise, extract and patch are done.
The current second condition is wrong, because it allows the following
sequence to happen:
- a non-custom kernel is used
- a previous build only partially extracted the non-custom sources
- that p[revious build broke during extraction (eg. incomplete tarball...)
- a subsequent build will find a properly named directory, and will
thus skip extract and patch, which is wrong
Fix that by following the conditions in this table:
Type | Extract | Patch
----------------------+---------+-------
Pre-installed headers | N | N
custom directory | N | N
custom tarball | Y | N
mainstream tarball | Y | Y
Signed-off-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Cc: David Holsgrove <david.holsgrove@xilinx.com>
Config options remain the same as before, just generalised to be used by other
components also.
Signed-off-by: "David Holsgrove" <david.holsgrove@xilinx.com>
[yann.morin.1998@free.fr: fix indentation, fix comment]
Signed-off-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Message-Id: <50674fe47431174aab80.1349931193@localhost.localdomain>
PatchWork-Id: 190786
GCC requires m68k arch tuples to be *-*-uclinux-* to support Linux on
no-mmu m68k (ColdFire) cpus.
Blackfin arch tuple must be *-*-linux-uclibc for FD_PIC_ELF toolchains,
so we cannot just switch to uclinux for no-mmu Linux toolchains.
Signed-off-by: "Esben Haabendal" <esben@haabendal.dk>
Message-Id: <876271s1ee.fsf@arh128.prevas.dk>
PatchWork-Id: 186976
build fails to symlink to custom kernel dir when the build is not the first time
because of 'ln -s' without '-f' option.
Signed-off-by: "Jang, Bongseo" <graycells@gmail.com>
Message-ID: <543e2981f2b723ecd850.1348370892@localhost.localdomain>
PatchWork-ID: 186178
Some longterm versions are not in the usual directory.
Account for these new locations.
Get rid of the mirror location, now that the main kernel site is
(almost) back to normal operations.
Signed-off-by: "Yann E. MORIN" <yann.morin.1998@anciens.enib.fr>
Allows using either a tarball or a directory as the custom kernel
source location.
Signed-off-by: Vincent BENOIT <sinseman44@gmail.com>
[yann.morin.1998@anciens.enib.fr: fix space damage, detailed commit message]
Signed-off-by: "Yann E. MORIN" <yann.morin.1998@anciens.enib.fr>
Since kernel.org is dead, and there is no announced or known estimated
time or return to normality, it is impossible to download any kernel at
this time.
Add a known-working mirror.
Signed-off-by: "Yann E. MORIN" <yann.morin.1998@anciens.enib.fr>
The custom-tarball symlink was created in CT_SRC_DIR, when it
should be created in CT_TARBALLS_DIR.
Reported-by: Guylhem Aznar <crossgcc@guylhem.net>
Signed-off-by: "Yann E. MORIN" <yann.morin.1998@anciens.enib.fr>
Simplify the way the custom tarball is handled:
- fake version="custom"
- at download, simply link the custom tarball to:
"linux-custom.${custom_extension}"
- at extract, the above allows to simply extract "linux-${LINUX_VERSION}"
where LINUX_VERISON is set to the fake version="custom"
Not that much convoluted, in fact... :-/
Signed-off-by: "Yann E. MORIN" <yann.morin.1998@anciens.enib.fr>
Someof the mingw32 source tarballs have an appended '-src' after the
version.
Since changeset #6e1412ba8da9 (scripts/functions: force extract folder
to archive basename), it means mingw tarballs get extracted in a directory
ending with '-src'.
Fix that.
Signed-off-by: "Yann E. MORIN" <yann.morin.1998@anciens.enib.fr>
The place to get 3.x has changed; the version scheme has changed.
No need to be overkill, just support 3.x; 4.x is not even dreamt of.
Signed-off-by: "Yann E. MORIN" <yann.morin.1998@anciens.enib.fr>
The location of the longterm Linux kernels on FTP has changed.
Here is a simple (but not very versatile) fix.
Signed-off-by: "Björn A. Herwig" <herwig@gdsys.de>
[yann.morin.1998@anciens.enib.fr: make it generic/versatile]
Signed-off-by: "Yann E. MORIN" <yann.morin.1998@anciens.enib.fr>
headers_install makes .install and ..install.cmd files.
headers_check makes .check and ..check.cmd files.
Remove these files uncoditionaly after installing (and checking) header files
into the sys-root.
Signed-off-by: Bryan Hundven <bryanhundven@gmail.com>
[Yann E. MORIN: reformat the patch, move hunk out of headers_check conditional]
Signed-off-by: "Yann E. MORIN" <yann.morin.1998@anciens.enib.fr>
Add the option to build a cross-compiler for kernel type 'mingw'.
The resulting cross-compiler can be used to build applications on a Linux host
that can be run on a Windows target.
Compiler is build using the mingwrt and w32-api packages aviable from the
MinGW project (http://sourceforge.net/projects/mingw).
The windows headers (w32-api package) are extracting with the kernel_headers
step The libraries and other headers from both packages are build and
installed in the various steps of libc
Signed-off-by: Bart vdr Meulen <bartvdrmeulen@gmail.com>
[yann.morin.1998@anciens.enib.fr: fix kernel headers comment, don't "return 0"]
Signed-off-by: "Yann E. MORIN" <yann.morin.1998@anciens.enib.fr>
Accept a local tarball name as the source of the Linux kernel headers,
rather than forcing the user to use either an upstream tarball, or a
local pre-installed headers tree.
For uClibc, the name of the Blackfin architecture is 'bfin'. Actually,
the naming of the architecture is quite messy: for toolchain tuples
and uClibc, it's bfin, but for the kernel, it's blackfin. We've
arbitraly choosen to name it "blackfin" in Crosstool-NG.
Add Blackfin-related uClibc patch to fix a build failure related to
fork() being used in unistd/daemon.c.
Yann E. MORIN:
Apply the patch to the kernel/linux build script to use 'linux'
in the noMMU tuples. See:
http://sourceware.org/ml/crossgcc/2010-04/msg00010.html
