crosstool-ng/patches/gcc/4.1.0/100-fix-fixincl.patch

72 lines
3.3 KiB
Diff
Raw Normal View History

See http://gcc.gnu.org/PR22541
From: Dan Kegel
When building gcc-3.4.3 or gcc-4.x into a clean $PREFIX,
the configure script happily copies the glibc include files from include to sys-include;
here's the line from the log file (with $PREFIX instead of the real prefix):
Copying $PREFIX/i686-unknown-linux-gnu/include to $PREFIX/i686-unknown-linux-gnu/sys-include
But later, when running fixincludes, it gives the error message
The directory that should contain system headers does not exist:
$PREFIX/lib/gcc/i686-unknown-linux-gnu/3.4.3/../../../../i686-unknown-linux-gnu/sys-include
Nevertheless, it continues building; the header files it installs in
$PREFIX/lib/gcc/i686-unknown-linux-gnu/3.4.3/include
do not include the boilerplate that would cause it to #include_next the
glibc headers in the system header directory.
Thus the resulting toolchain can't compile the following program:
#include <limits.h>
int x = PATH_MAX;
because its limits.h doesn't include the glibc header.
The problem is that gcc/Makefile.in assumes that
it can refer to $PREFIX/i686-unknown-linux-gnu with the path
$PREFIX/lib/../i686-unknown-linux-gnu, but
that fails because the directory $PREFIX/lib doesn't exist during 'make all';
it is only created later, during 'make install'. (Which makes this problem
confusing, since one only notices the breakage well after 'make install',
at which point the path configure complained about does exist, and has the
right stuff in it.)
A fix that I've been using for a while is to use sed to canonicalize
the path. The sed syntax is a bit obtuse, but it works.
(hey, that's the first time I've ever used a label in a sed script; thanks to the sed faq
for explaining the :a ... ta method of looping to repeat a search-and-replace until it doesn't match.)
[rediffed against gcc-4.1-20060210]
--- gcc-4.1-20060210/gcc/Makefile.in.old 2006-01-11 06:29:29.000000000 -0800
+++ gcc-4.1-20060210/gcc/Makefile.in 2006-02-14 16:08:54.000000000 -0800
@@ -388,7 +388,10 @@
CROSS_SYSTEM_HEADER_DIR = @CROSS_SYSTEM_HEADER_DIR@
# autoconf sets SYSTEM_HEADER_DIR to one of the above.
-SYSTEM_HEADER_DIR = @SYSTEM_HEADER_DIR@
+# Purge it of unneccessary internal relative paths
+# to directories that might not exist yet.
+# The sed idiom for this is to repeat the search-and-replace until it doesn't match, using :a ... ta.
+SYSTEM_HEADER_DIR = `echo @SYSTEM_HEADER_DIR@ | sed -e :a -e "s,[^/]*/\.\.\/,," -e ta`
# Control whether to run fixproto and fixincludes.
STMP_FIXPROTO = @STMP_FIXPROTO@
@@ -3167,13 +3170,15 @@
../$(build_subdir)/fixincludes/fixincl: ; @ :
# Build fixed copies of system files.
+# Abort if no system headers available, unless building a crosscompiler.
+# Canonicalize $gcc_tooldir/sys-include in same way as $SYSTEM_HEADER_DIR was canonicalized so test still works
stmp-fixinc: gsyslimits.h macro_list \
$(build_objdir)/fixincludes/fixincl \
$(build_objdir)/fixincludes/fixinc.sh
@if ! $(inhibit_libc) && test ! -d ${SYSTEM_HEADER_DIR}; then \
echo The directory that should contain system headers does not exist: >&2 ; \
echo " ${SYSTEM_HEADER_DIR}" >&2 ; \
- if test "x${SYSTEM_HEADER_DIR}" = "x${gcc_tooldir}/sys-include"; \
+ if test "x${SYSTEM_HEADER_DIR}" = "x`echo "${gcc_tooldir}/sys-include" | sed -e :a -e "s,[^/]*/\.\.\/,," -e ta`"; \
then sleep 1; else exit 1; fi; \
fi
rm -rf include; mkdir include